ELECTRIC HEIGHT-ADJUSTED SIT TO STAND DESK Vortex Series 2-leg Desk Assembly Guide For desk with underframe Model No.
Table of Contents IMPORTANT SAFETY INSTRUCTIONS .................................................................................................... 3 CAUTION, USE & LIABILITY .......................................................................................................................... 4 PARTS & HARDWARE ..................................................................................................................................... 5 ASSEMBLY INSTRUCTIONS ....................................
IMPORTANT SAFETY INSTRUCTIONS WARNING –When using electric appliances, basic precautions should always be followed, including the following: a) Read all the instructions before using the appliance. b) To reduce the risk of injury, close supervision is necessary when an appliance is used near children. c) Do not contact moving parts. d) Only use attachments recommended or sold by the manufacturer. e) Do not use outdoors.
CAUTION, USE & LIABILITY CAUTION Make sure no obstacles are in the desk’s path. Make sure the desk is not touching any walls. Make sure all cords are of appropriate lengths to accommodate the change in desk height. Keep children away from electric sit to stand desks, control units and handsets. Keep all electrical components away from liquids. Do not sit or stand on desk. Do not crawl or lie under desk. Do not place any objects taller than 20” underneath desk.
PARTS & HARDWARE PARTS DIAGRAM Upper Support Tabletop Controller Leg Foot PARTS LIST Foot (2) Leg (2) Beam (1) Controller (1) Upper Support (2) (For Memory Controller) HARDWARE LIST ST2.
ASSEMBLY INSTRUCTIONS BEFORE YOU BEGIN 1. Lay out all components and hardware to ensure that you have all the parts listed on the parts on page 5. 2. Desk weighs close to 100 lbs. Two people are needed to turn or move desk and some of its components. When turning or moving the assembled desk, grab it by UPPER SUPPORTS (not desk top). 3. Assemble on soft and non-abrasive surface to avoid scratch or damage to the desk top.
STEP 2 Remove the protective cap and insert the hexagon spindle into gear box on the beam. Please note the marking R and L on the beam and legs. Right leg should connect to right side of the beam, and left leg to left side of the beam. VERY IMPORTANT: Minor adjustment to the spindle head may be needed to set it properly into gearbox. Use a tool like a wrench to turn the spindle head slightly left or right if needed.
STEP 3 Use Screw A to secure two upper supports to the beam. STEP 4 (Mounting matching top from us) Lay the table top on a soft and non-abrasive surface. Carefully move the underframe onto the top, align the holes on the upper supports to the pre-drilled anchors on the top. Secure the top with Screw A. Don’t overtighten the screws. Use longer Screw F1 to mount non-memory controller, and shorter Screw F2 for memory controller. If F1 Screw is used to mount memory controller, it will go thru the top.
STEP 4-1 (Mounting your own top) Optional: Find a separate hardware bag labeled “Anchors for top”. Install those anchors to your own top, and follow instruction STEP 4. Some users choose not to install anchors and simply use their own wood screws to mount Support Brackets to the top. Those wood screws are not provided. Please check the length of the screws before mounting and make sure that they don’t go through the top.
Memory Function Controller for Desk Underframe Model# AL4628-2M Preset 1 Preset 2 Preset 3 Preset 4 LED Display Up Button Down Button a. LED panel displays minimum height of 28.5” and maximum height of 46.6” b. Factory default settings for four memory buttons are 32.1”, 35.7”, 39.3” and 42.9” respectively. c. To set your own height, press up or down button until the desk reaches the desired height, press and hold memory button until you hear two beeps.
TROUBLESHOOTING Issues(s) Desk does not go up or down Desk is unsteady Limited range When up or down button is pressed, the desk moves the opposite way. Desk goes up or down normally grinding sound present Desk goes up or down unevenly grinding sound present Desk goes up or down unevenly grinding sound not present. Solution Check all connections. Make sure controller box is plugged into a power outlet and controller is plugged into control box.
WARRANTY INFORMATION SCOPE OF WARRANTY Apex Furniture LLC (“ApexDesk”) warrants to the original purchaser its new desk (except for components not warranted under “Exclusions”) manufactured by ApexDesk to be free from defects in material and workmanship under normal use and service.