IP Wireless / Wired Camera NIGHT VISION & REMOTE PAN/TILT ROTATE User Manual
WELCOME This model IP Camera is an integrated wireless IP Camera solution. It combines a high quality digital Video Camera with network connectivity and a powerful web server to bring clear to your Desktop from anywhere on your local network or over the Internet. The basic function of it is transmitting remote video on IP network. The high Quality video image can be transmitted with 30fps speed on the LAN/WAN by using MJPEG hardware compression technology. This is based on the TCP/IP standard.
—1— Advanced Features Multi-Protocol support and Transportation IP CAMERA supports Multi-Protocol such as TCP/IP, SMTP and HTTP. Sending the image to your mailbox automatically when the IP CAMERA is triggered. Video Image PTZ function Users can control the camera direction on the video image. Motion Detection Your may use the internal Motion Detection function or external sensor to trigger images Recording and transportation. Alarm sensor input/output.
Click Start>Running, and enter “command” (for Windows 95/98/ME) or “cmd” (for Windows2000/XP). Then select “OK” and enter “ipconfig”, press enter. The basic setting of your network will be shown as follow: Please record the IP Address, Subnet Mask, and Default Gateway. ( For example : MY router ip address is 192.168.11.1) You might use this information to set your device. Insert the accessory CD into the CD-ROM,.
Open come with CD 1)Install OCX.exe.
3)Choice IP address Æ Open device->IE Browse login Input Default User name:admin Password:admin Login ip camera 1)video monitor
Video attribute settings and PTZ(Pan/Tilt/Zoom) control operations Function Description:
Window: the window is defined as video window number shown in the video region ,the current maximum of which were 36. Resolution: the size of the currently selected video. Currently supports two sizes: 640x480 and 320x240. Mode: set the video light mode, and remove the jitter impact of the image as per the electricity frequency. The following three modes are used: 50HZ/60HZ /outdoor model. Generally, indoor mode use 50Hz or 60Hz, outdoor mode should be set as per the real camera working environment.
Description: when the window is selected, the border of the window will become red. Double-click to select the screen, and the screen automatically changes to full-screen mode. To return to its original state, please double-click the screen again.
smart phone Device Information Display the status information of the device.
1, User can customize the name of the device in order to distinguish different equipments. 2, When the video surveillance equipment connected, the page will show the device and the name. 3, The search tool can also display the searched device names. 3: Net config: set up network-related parameters. 3.
Net Config: IP Config 1) The set supports two modes of distribution network address: 2) 1, to obtain IP address automatically (DHCP): Select DHCP, device will automatically obtain the IP, which is not fixed (this feature requires the router to support DHCP protocol, and this feature should be activated). 3) 2, using the specified IP address (static IP): To specify the equipment IP, it is required to manually fill in IP address.
Note: It is use set wire IP camera IP address. WIFI Config This function is Use Wifi IP Camera After setting up WiFi parameters, such as Password, Authentication parameters, please select "Enable" and restart the device. Then, the user will be able to access the network through a wireless network of cameras.
You choice the SSID name same to router and you make sure You PC->wireless router Encrypt: WEP /WPA2-PSK-TKIP
Dynamic DNS This equipment support dynamic DNS of www.dyndns.org. Enter the applied dynamic domain name, user name, password, and click “Save” to access device through WAN. if you need see interenet or cellphone When use this function you need you need register a DDNS (xxx.dyndns.org) in WWW.dyndns.com login in you wireless router set port forwarding and upnp 1) Step 1: enter http://www.dyndns.
Account Step2: enter your information Step3: After a minute, you will receive a E-mail from DynDNS Support and it will give you a confirmation address (e.g. https://www.dyndns.com/account/confirm/vXMVT78-KvenhydmKMWH5kg) —32— Step4: When the Account Confirmed, login and start using your account. Choose Add Host Services(Figure 4.4) and enter Add New Hostname (Figure 4.5) page.
—33— Step5: On the Add New Hostname page 1) input your Hostname.
2) Choose Host with IP address 3) Click Use auto detected IP address xxx.xx.xx.xxx Then click Create Host. Step6: Now you obtained a Dynamic Domain Name(Figure 4.
3) upnp settings Upnp is to realize automatic port mapping function. If the camera is connected to a router, In order to access to the cameras through WAN, it is required to open a specified port of the router to the camera. (This feature requires router support, and this feature should be open. Without this feature, you need to manually set up port mapping in the router). If the upnp enabled successfully, the below figure will be displayed.
Port config This page is used to set the camera's external ports, the default value of 80. If you want to visit the multiple cameras in a same local area network through WAN, in order to distinguish different cameras, each camera needs a different port, such as 81, 82, etc. and so on. Alarm camera settings are used to set the alarm function of network camera. When external alarm signal is triggered, alarm will come. The alarm device can be high sound alarm device or sound &light alarms device.
Motion detect config The IPCamera can do motion detect and trigger some action if necessary, such as upload picture to FTP, send email with picture as attachment, or start record automatically.
You can choice High ,Medium, Low IO Alarm Enable or disable IO alarm at this page Alarm Input port - +12v
SMTP config Provide email sender information here, which is need for send email when motion detects or other alarm is occurring. FTP config Fill FTP information here, which is need to upload images to FTP server.
Chapter VII of the System Tools Restart the equipment When settings changes happen, it is required to restart your device to the changes to take effect, you can click on the page "Reboot Device" to enable the device to restart. Another 20 seconds is needed to finish the device initialization. 7.2 to restore the factory settings Click "reset configt" will enable the device to restore all settings to factory default, the default user name and password are both “admin”.
Note: The factory default settings using DHCP to obtain IP address. After restoring the factory settings, device IP address may be different from the one before restoration. Please use the search tool to search for equipment. And obtain the corresponding IP. 7.3 User Management In this page, user permissions management is applied. According to different users name, different operating authority setting can be configured. Administrator has the privilege to operate all functions of the camera.
Users can be enabled or disabled. The disabled users can’t log on equipment page. Description: user "admin" is the super-administrator user, who can set up and operate all the functionalities of all the networking cameras. 7.4 Multiple Devices Manager In this page, not only the main video, but also additional device can be connected be automatically. This page is for the maintenance of additional equipment, create, modify, and delete equipment.
The next figure describe how to add/edit the additional device. 7.5 Local config To set video recording and photographing saving directory, it is required to input save path in "captured photo file" and "video record file". 7.6 Download Ocx control Clicking on the link in this page is available for download ocx control.
7.7 Update Software Updating software is to enable users to use the latest software. The upgrade file name is app.bin, Click button "Browse" to find out the path where app.bin is stored. You can click to upgrade, the system will show the upgrading files progress, success information will be prompted if upgrading successfully. The new networking camera must be restarted to take the new program effect. 7.
successfully. The new networking camera must be restarted to take the new program effect. Chapter VIII Logout Logging out from the current registry, it will return to the login page. Login must be accomplished again if the user wants to operate the equipment again. How to use IPCamMaster IPCamMaster is used to manage the activities of multiple IPCamera devices, such as photographing, video recording, PTZ(Pan/Tilt/Zoom) control panel operations and etc.
Install Double click 1) 2) Double click 3)
4)
Thanks for your buy our products If you any questions please contact me Eamil: Universe-Sword@hotmail.
