APC-3x97B User Manual (SBC-7106) Fanless Total IP65 Intel Atom D2550 Stainless Steel Panel PC Release Date _ Revision Oct. 2014 ® 2014 Aplex Technology, Inc. V1.2 All Rights Reserved. Published in Taiwan Aplex Technology, Inc. 15F-1, No.186, Jian Yi Road, Zhonghe District, New Taipei City 235, Taiwan Tel: 886-2-82262881 Fax: 886-2-82262883 E-mail: aplex@aplex.com.tw APC-3x97B (SBC-7106) User Manual URL: www.aplex.com.
Warning!___________________________________ This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual, it may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment.
Packing List Accessories (as ticked) included in this package are: □ Power Connector □ Driver & manual CD disc □ Other.___________________(please specify) Safety Precautions Follow the messages below to prevent your systems from damage: ◆ Avoid your system from static electricity on all occasions. ◆ Prevent electric shock. Don‘t touch any components of this card when the card is power-on. Always disconnect power when the system is not in use. ◆ Disconnect power when you change any hardware devices.
Table of Contents______________________ Warning!…………………………………………………………………………….……..….2 Packing List…………………………………………………………………………………..3 Safety Precautions…………………………………………………………………………..3 Chapter 1 1.1 1.2 1.3 1.4 Getting Started Features…………………………………………..….……………………..6 Specifications……………………………………………..........................6 Dimensions………………………………...………………………….........8 Brief Description of APC-3X97B………………………………….………9 Chapter 2 Hardware 2.1 Mainboard…..……………..…….……………………………………..…..10 2.2 Introduction..…….
.2 Installing Software …………..………….................................................50 5.3 Software Functions...............................................................................54 Figures Figure 1.1: Dimensions of APC-3597B………………….………………..…....8 Figure 1.2: Front View of APC-3X97B……………..……..…………………….9 Figure 1.3: Rear View of APC-3X97B……………..……………………………9 Figure 2.1: Mainboard Dimensions…………………………………..…….....12 Figure 2.2: Jumpers and Connectors Location_ Board Top………………...13 Figure 2.
Chapter 1 Getting Started 1.1 Features Fanless Design Intel® Atom™ Processor D2550 Onboard 2GB DDR3 800 MHz 11~32V DC wide-ranging power input Total 6 sides IP 65 5-Wire Resistive Touch Screen 1.2 Specifications APC-3597B System CPU Motherboard Intel® Atom Processor D2550 (1M Cache, 1.8 GHz) Intel® Atom Processor N2600 (1M Cache, 1.
Expansion Slot 1 x Mini PCIe half size Option WLAN/BT Module and Antenna Display Display Type 15” Color TFT LCD Max. Resolution 1024x768 Max. Color 262K Luminance (cd/m²) 400 View angle(H°/V°) 160/145 Contrast Ratio 800:1 Backlight lifetime(hrs) 50000 Touch screen Type Resistive Type Interface Default RS-232 Light Transmission(%) 80% Power Power Input 11~32V DC Mechanical Construction IP Rating Stainless steel Total IP65 Mounting VESA 75 x 75 Dimension (mm) 399 x 324 x 52.
1.3 Dimensions Figure 1.
1.4 Brief Description of APC-3X97B APC-3X97B series comes with IP65 certificated and is powered by Intel Atom D2550 to provide low power consumption. The stainless steel chassis design makes it exceptionally suitable for strict hygiene regulations for food/chemical industry, medical, restaurant/kitchen applications, storage management and outdoor /information segment and so on. APC-3X97B series has LCD size in 15”. APC-3X97B supports 5 wires resistive touch.
Chapter 2 Hardware 2.1 Mainboard Specifications Board Size 170mm x 113mm CPU Support Intel® Atom Processor D2550 (1M Cache, 1.
Digital I/O 8-bit digital I/O Pin header via CN2 4-bit digital Input 4-bit digital Output 4-bit digital I/O Pin header via CN3 2-bit digital Input 2-bit digital Output Battery Audio Support CR2477 Li battery by 2-pin header Realtek ALC662 HD audio codec Line-in, Line-out, MIC via 2x6-pin header Audio Line out in phone jack Keyboard /Mouse 1 x PS2 keyboard/mouse 1x6 box pin header via CN3 Expansion Bus 1 x mini-PCI-express slot 1 x PCI-express via CN3 Option WLAN/BT Module and Antenna Touch Ctrl 1 x
(units :mm) Figure 2.
2.2 Introduction SBC-7106 is a 4" industrial motherboard developed on the basis of Intel Cedarview-M Processors and NM10, which provides abundant peripheral interfaces to meet the needs of different customers. Also, it features dual GbE ports, 3-COM ports and one Mini PCIE configuration, one VGA port, one HDMI port, one LVDS interface. To satisfy the special needs of high-end customers, CN1 and CN2 and CN3 richer extension functions. The product is widely used in various sectors of industrial control. 2.2.
Board Bottom Figure 2.
2.3 Jumpers Setting and Connectors 1. JP5: (2.0mm Pitch 1X2 box Pin Header),ATX Power and Auto Power on jumper setting. 3. JP5 Mode Open ATX Power Close Auto Power on (Default) BAT1 : (1.25mm Pitch 1X2 box Pin Header) 3.0V Li battery is embedded to provide power for CMOS. 4. Pin# Signal Name Pin1 VBAT PIN2 Ground DC_IN1: (5.08mm Pitch 1x3 Pin Connector),DC9V~36V System power input connector。 6. Pin# Power Input Pin1 DC+9V~32V Pin2 Ground Pin3 FG VGA1: (CRT 2.
9. CRT_V_SYNC 9 10 CRT_DDCCLK Ground 11 12 Ground RS-232: (Switch),COM1 jumper setting, it provides selectable RS232 or RS422 or RS485 serial signal output. Function 10. S_232 Pin# RS232 (Default) ON: Pin1, Pin2, Pin3, Pin4, Pin5 RS422 (option) OFF: Pin1, Pin2, Pin3, Pin4, Pin5 RS485 OFF: (option) Pin1, Pin2, Pin3, Pin4, Pin5 RS-422: (Switch),COM1 setting, it provides selectable RS232 or RS422 or RS485 serial signal output.
RS232 (Default): Pin# Signal Name 1 DCD# (Data Carrier Detect) 2 RXD (Received Data) 3 TXD (Transmit Data) 4 DTR (Data Terminal Ready) 5 Ground 6 DSR (Data Set Ready) 7 RTS (Request To Send) 8 CTS (Clear To Send) 9 JP1 select Setting (RI/5V/12V) BIOS Setup： Advanced/W83627UHG Super IO Configuration/Serial Port 1 Configuration【RS-232】 RS422 (option): Pin# Signal Name 1 422_RX+ 2 422_RX- 3 422_TX- 4 422_TX+ 5 Ground 6 NC 7 NC 8 NC 9 NC BIOS Setup： Advanced/W83627UHG Super
9 NC BIOS Setup： Advanced/W83627UHG Super IO Configuration/Serial Port 1 Configuration【RS-485】 13. COM2: (Type DB9),Rear serial port, standard DB9 Male serial port is provided to make a direct connection to serial devices. Pin# Signal Name 1 DCD# (Data Carrier Detect) 2 RXD (Received Data) 3 TXD (Transmit Data) 4 DTR (Data Terminal Ready) 5 Ground 6 DSR (Data Set Ready) 7 RTS (Request To Send) 8 CTS (Clear To Send) 9 NA 16. LED3: LED STATUS. Green LED for Touch Power status.
provide high quality audio I/O ports. Line Out can be connected to a headphone or amplifier. 24. USB45: USB4/USB5：(Double stack USB type A), Rear USB connector, it provides up to 4 USB2.0 ports, High-speed USB 2.0 allows data transfers up to480 Mb/s ,support USB full-speed and low-speed signaling. Each USB Type A Receptacle (2 Ports) Current limited value is 1.5A. If the external USB device current exceeds 1.5A, please separate connectors into different Receptacle. 25.
31. CN3: (1.27mm Pitch 2X30 Pin Header), For expand output connector, It provides four GPIO, Two USB 2.0,one PS/2 mouse，one PS/2 keyboard,two uart,one PCIe x1,one SMbus.
Chapter 3 BIOS Setup 3.1 Operations after POST Screen After CMOS discharge or BIOS flashing operation,.Press [Delete] key to enter CMOS Setup. After optimizing and exiting CMOS Setup, the POST screen displayed for the first time is as follows and includes basic information on BIOS, CPU, memory, and storage devices. 3.2 BIOS Setup Utility Press [Delete] key to enter BIOS Setup utility during POST, and then a main menu containing system summary information will appear.
3.
System Time Set the system time, the time format is : Hour: 0 to 23 Minute: Second 0 to 59 0 to 59 System Date Set the system date, the date format is: Note that the ‘Day’ automatically changes when you set the date. Day: 01 to 12 Month: 01 to 31 Date: 1998 to 2099 Year: 3.4 Advanced Settings 3.4.1 PCI Subsystem Settings PCI Bus Driver Versio V2.05.
PCI Latency Timer: [32 PCI Bus Clocks] [64 PCI Bus Clocks] [96 PCI Bus Clocks] [128 PCI Bus Clocks] [160 PCI Bus Clocks] [192 PCI Bus Clocks] [224 PCI Bus Clocks] [248 PCI Bus Clocks] VGA Palette Snoop: [Disabled] [Enabled] PERR# Generation: [Disabled] [Enabled] SERR# Generation: [Disabled] [Enabled] 3.4.
S3 Video Repost: [Disabled] [Enabled] 3.4.3 CPU Configuration Processor Type EMT64 Processor Speed System Bus Speed Ratio Status Actual Ratio System Bus Speed Processor Stepping Intel(R) Atom(TM) CPU N2600 Not Supported 1600 MHz 400 MHz 16 16 400 MHz 30661 Microcode Revision L1 Cache RAM L2 Cache RAM 269 2 x 56k 2 x 512k Processor Core Hyper-Threading Dual Supported Hyper-Threading: [Enabled] [Disabled] Execute Disable Bit: [Enabled] [Disabled] Limit CPUID Maximum: [Disabled] [Enabled] 3.4.
Active Trip Point Hi [71C] Passive Trip Point [95] Passive TC1 Value 1 Passive TC2 Value Passive TSP Value 3.4.5 IDE Configuration SATA Port0 SATA Port1 5 10 Not Present Not Present SATA Controller(S): [Enabled] [Disabled] Configure SATA as: [IDE] [AHCI] Misc Configuration for hard disk 3.4.
[Auto] [Manual] Mass Storage Devices： Multiplecard Reader 1 [Auto] [Floppy] [Forced FDD] [Hard Disk] [CD-ROM] 3.4.7 W83627UHG Super IO Configuration W83627UHG Super IO ch W83627UHG Serial Port 1 Configuration UART Mode Selection： [RS-232] [RS-485] [RS-422] Serial Port 2 Configuration Serial Port 3 Configuration UART Mode Selection： [RS-485] [RS-422] Serial Port 4 Configuration Serial Port 5 Configuration Serial Port 6 Configuration Power Failure [Keep last state] [Always off] [Always on] 3.4.
AVCC VCC5V VSB5 : +5.203V : +5.216V : +5.203V VBAT : +3.334V 3.4.9 Serial Port Console Redirection COM0 Console Redirection [Enabled] [Disabled] Console Redirection Settings Serial Port for Out-of-Band Management/ Windows Emergency Management Services (EMS) Console Redirection [Disabled] [Enabled] Console Redirection Settings 3.4.
[Enabled] [Disabled] C-state POPUP [Enabled] [Disabled] 3.5 Chipset Settings 3.5.
MRC Fast Boot [Enabled] [Disabled] Max TOLUD [Dynamic] [1GB] [1.25GB] [1.5GB] [1.75GB] [2GB] [2.25GB] [2.5GB] [2.75GB] [3GB] [3.
[Force Scaling] [off] [Maintain Aspect Ratio] Active LFP [LVDS] [No LVDS] [EDP] IGD Clock Source [External Clock] [Internal Clock] Fixed Graphics Memory [128MB] [256MB] ALS Support [Disabled] [Enabled] Back light Control [DC] [PWM] Back light Logic [Positive] [Negative] Back light Control Lev [Auto] [Disabled] [Level 8] [Level 1] [Level 2] [Level 3] [Level 4] [Level 5] [Level 6] [Level 7] [Level 8] APC-3x97B (SBC-7106) User Manual 31
[Level 9] [Level 10] [Level 11] [Level 12] [Level 13] [Level 14] [Level 15] 3.5.2 South Bridge TPT Devices PCI Express Root Port 0 PCI Express Root Port 1 PCI Express Root Port 2 PCI Express Root Port 3 DMI Link ASPM Control [Enabled] [Disabled] PCI-Exp.
3.
Skip VGA [Enabled] [Disabled] Skip USB [Disabled] Enabled] Skip PS2 [Disabled] [Enabled] CSM16 Module Version 07.
[Legacy only] [UEFI only] Launch PXE OpROM poli [Do not Launch] [UEFI only] [Legacy only] Launch Storage OpROM [Legacy only] [Do not Launch] [UEFI only] Launch Video OpROM po [Do not Launch] [UEFI only] [Legacy only] Other PCI device ROM [UEFI OpROM] [Legacy OpROM] APC-3x97B (SBC-7106) User Manual 35
3.7 Security Settings 3.7.1 Administrator Password 3.7.2 User Password Type the password with up to 20 characters and then press Enter key. This will clear all previously typed CMOS passwords. You will be requested to confirm the password. Type the password again and press Enter key. You may press Esc key to abandon password entry operation. To clear the password, just press Enter key when password input window pops up.
Once the password feature is used, you will be requested to type the password each time you enter BIOS setup. This will prevent unauthorized persons from changing your system configurations. Also, the feature is capable of requesting users to enter the password prior to system boot to control unauthorized access to your computer. Users may enable the feature in Security Option of Advanced BIOS Features.
Exit Without Saving Quit without saving? [Yes] [No] Save Changes and Reset Save & reset Save Configuration and reset? [Yes] [No] Discard Changes and Reset Reset Without Saving Reset without saving? [Yes] [No] Save Changes Save Setup Values Save configuration? [Yes] [No] Discard Changes Load Previous Values Load Previous Values? [Yes] [No] Restore Defaults Load Optimized Defaults Load optimized Defaults? [Yes] [No] Save user Defaults Save Values as User Defaults Save configuration? [Yes] [No] Restore user De
Chapter 4 Installation of Drivers This chapter describes the installation procedures for software and drivers under the windows 7. The software and drivers are included with the motherboard. The contents include Intel chipset driver, VGA driver, LAN drivers, Audio driver Installation instructions are given below.
4.1 Intel Chipset Driver To install the Intel chipset driver, please follow the steps below. Step 1. Select Intel (R) Chipset NM10 Express from the list Step 2. Click Next to setup program.
Step 3. Read the license agreement. Click Yes to accept all of the terms of the license agreement. Step 4. Click Next to continue.
Step 5. Click Next. Step 6. Select Yes, I want to restart this computer now. media from the drives.
4.2 Intel Graphics Media Accelerator Driver To install the VGA drivers, follow the steps below to proceed with the installation. Step 1.Select Intel(R) VGA Chipset Driver. Step 2. Tick Automatically run WinSAT and enable the Windows Aero desktop theme(if supported). Click Next.
Step 3. Read license agreement. Click Yes. Step 4. Click Next.
Step 5. Click Next. Step 6. Select Yes, I want to restart this computer now. APC-3x97B (SBC-7106) User Manual Click Finish.
4.3 Intel (R) Network Adapter To install the Intel (R) Network Adapter device driver, please follow the steps below. Step 1. Select LAN Driver. Step 2.
Step 3. Click Next to continue. Step 4. Click Install to begin the installation.
Step 5. Click Finish to exist the wizard. 4.4 Realtek ALC662 HD Audio Codec Driver Installation To install the Realtek ALC662 HD Audio Codec Driver, please follow the steps below. Step 1.
Step 2. Click Next to continue. Step 3. Click Yes, I want to restart my computer now. APC-3x97B (SBC-7106) User Manual Click Finish to complete the installation.
Chapter 5 Touch Screen Installation This chapter describes how to install drivers and other software that will allow your touch screen work with different operating systems. 5.1 Windows 2000/XP/2003/Vista/WIN7 Universal Driver Installation for PenMount 6000 Series Before installing the Windows 2000/XP driver software, you must have the Windows 2000/XP system installed and running on your computer.
Step 2. Click Next to continue. Step 3. Read the license agreement. APC-3x97B (SBC-7106) User Manual Click I Agree to agree the license agreement.
Step 4. Choose the folder in which to install PenMount Windows Universal Driver. Click Install to start the installation. Step 5. Wait for installation. Then click Next to continue.
Step 6. Click Continue Anyway. Step 7. Click Finish to complete installation.
5.3 Software Functions Upon rebooting, the computer automatically finds the new 6000 controller board. The touch screen is connected but not calibrated. Follow the procedures below to carry out calibration. 1. After installation, click the PenMount Monitor icon “PM” in the menu bar. 2. When the PenMount Control Panel appears, select a device to “Calibrate.
Advanced Calibration Advanced Calibration uses 4, 9, 16 or 25 points to effectively calibrate touch panel linearity of aged touch screens. Click this button and touch the red squares in sequence with a stylus. To skip, press ESC’. Command Calibration Command call calibration function. Use command mode call calibration function, this can uses Standard, 4, 9, 16 or 25 points to calibrate E.g. Please run ms-dos prompt or command prompt c:\Program Files\PenMount Universa Driver\Dmcctrl.
Step 2.Click “Standard Calibration” to start calibration procedure NOTE: The older the touch screen, the more Advanced Mode calibration points you need for an accurate calibration. Use a stylus during Advanced Calibration for greater accuracy.
Step 3.Come back to “PenMount Control Panel” and select Tools then click Advanced Calibration. Step 4. Select Device to calibrate, then you can start to do Advanced Calibration. NOTE: Recommend to use a stylus during Advanced Calibration for greater accuracy.
Plot Calibration Data Check this function and a touch panel linearity comparison graph appears when you have finished Advanced Calibration. The blue lines show linearity before calibration and black lines show linearity after calibration. Turn off EEPROM storage The function disable for calibration data to write in Controller. The default setting is Enable. Setting Touch Mode This mode enables and disables the mouse’s ability to drag on-screen icons – useful for configuring POS terminals.
About This panel displays information about the PenMount controller and driver version.
Multiple Monitors Multiple Monitors support from two to six touch screen displays for one system. The PenMount drivers for Windows 2000/XP support Multiple Monitors. This function supports from two to six touch screen displays for one system. Each monitor requires its own PenMount touch screen control board, either installed inside the display or in a central unit. The PenMount control boards must be connected to the computer COM ports via the RS-232 interface.
3. Touch each screen as it displays “Please touch this monitor”. Following this sequence and touching each screen is called mapping the touch screens. 4. Touching all screens completes the mapping and the desktop reappears on the monitors. 5. Select a display and execute the “Calibration” function. A message to start calibration appears. Click OK. 6. “Touch this screen to start its calibration” appears on one of the screens. Touch the screen. 7. “Touch the red square” messages appear.
NOTES: 1. If you use a single VGA output for multiple monitors, please do not use the Multiple Monitor function. Just follow the regular procedure for calibration on each of your desktop monitors. 2. The Rotating function is disabled if you use the Multiple Monitor function. 3. If you change the resolution of display or screen address, you have to redo Map Touch Screens, so the system understands where the displays are.
Control Panel Open Control Panel Windows Beep Setting Beep function for each device Right Button When you select this function, a mouse icon appears in the right-bottom of the screen. Click this icon to switch between Right and Left Button function. Exit Exits the PenMount Monitor function. PenMount Rotating Functions The PenMount driver for Windows 2000/XP supports several display rotating software packages.
