ARCHMI-7XX User Manual Release Date _ Revision Oct. 2014 ® 2014 Aplex Technology, Inc. Taiwan V1.6 All Rights Reserved. Published in Aplex Technology, Inc. 15F-1, No.186, Jian Yi Road, Zhonghe District, New Taipei City 235, Taiwan Tel: 886-2-82262881 Fax: 886-2-82262883 E-mail: aplex@aplex.com.tw www.aplex.com.
Warning!_____________________________ This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions manual, it may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment.
Packing List Accessories (as ticked) included in this package are: □ Adaptor □ Driver & manual CD disc □ Other.___________________(please specify) Safety Precautions Follow the messages below to prevent your systems from damage: ◆ Avoid your system from static electricity on all occasions. ◆ Prevent electric shock. Don‘t touch any components of this card when the card is power-on. Always disconnect power when the system is not in use. ◆ Disconnect power when you change any hardware devices.
Table of Contents___________________ Warning!/Avertissement!............................…………………………….……..….2 Caution/Precaution/Disclaimer……………………………………………………2 Packing List…………………………………………………………………………..3 Safety Precautions/Consignes de sécurité……….……………………………..3 Chapter 1 Getting Started 1.1 Specifications…………………………...…………………………..6 1.2 Dimensions………..………………………...………………….......9 1.3 Brief Description of ARCHMI Series…………………….………14 1.4 Installation of HDD (ARCHMI-707/ARCHMI-708)…..…………16 1.
.2 Software Functions……………………………………………….88 5.2.1 Software Functions (Resistive Touch)...................................88 5.2.2 Software Functions (Projected Capacitive)……….……...….97 Figures Figure 1.1: Dimensions of ARCHMI-707…....………………..……...9 Figure 1.2: Dimensions of ARCHMI-708……..……….………..…..10 Figure 1.3: Dimensions of ARCHMI-710………………………..…..11 Figure 1.4: Dimensions of ARCHMI-712……………………....……12 Figure 1.5: Dimensions of ARCHMI-715…………………….......…13 Figure 1.6: Front View of ARCHMI SERIES……………….
Chapter 1 Getting Started 1.1 Specifications ARCHMI -707(P) System CPU ARCHMI -708(P) ARCHMI -710(P) ARCHM -712(P) ARCHMI -715(P) Intel Atom Cedar View N2600 1.6GHz Dual Core Processors /Intel Atom D2550 1.8GHz (Optional for ARCHMI-712(P)/715(P) only) Intel NM10 System Chipset System Onboard DDR3 2GB 800 MHz /4GB (Optional for ARCHMI-712(P)/715(P) only) Memory IO Port USB 2 x USB 2.
Lifetime Touch Screen Type Resistive Touch / Projected Capacitive Touch (for P model) Interface RS-232 / USB (for P model) Light 80% / 90% (for P model) Transmission (%) Power Power Input 9~36V DC Mechanical Construction Sliver aluminum front bezel and chassis IP Rating IP65 front panel Mounting Panel mounting, VESA 75 x 75 Panel mounting, VESA 100 x 100 Dimension 202 x 149 x 39 231 x 176 x 51 285 x 189 x 48.9 319 x 245 x 51.68 410 x 310 x 54.67 (mm) Net Weight 1.2 1.8 2 2.5 4.
1.2 Dimensions Figure 1.
Figure 1.
Figure 1.
Figure 1.
Figure 1.
1.3 Brief Description of ARCHMI Series There are 7”, 8”, 10.1”, 12.1”, 15”, Industrial Compact Size Panel PC in ARCHMI series, which comes with flat front panel touch screen and fanless design. It is powered by Intel Atom N2600 1.6GHz CPU built-in, 2GB DDR III 800 MHz, and now it also can be powered by Intel Atom D2550 1.8GHz CPU built-in, 4GB DDR III 800MHz optional for ARCHMI-712 and ARCHMI-715. ARCHMI series is 9~36VDC wide-ranging power input and IP65 compliant front panel.
Figure 1.6: Rear View of ARCHMI -707/ARCHMI -708 Figure 1.7: Rear View of ARCHMI-710 Figure 1.
1.4 Installation of HDD (ARCHMI-707/ARCHMI-708) Step 1 There are 2 screws to deal with when enclosing or removing the chassis. Gently remove 2 screws. Step 2 There is a SSD card in the bracket. Gently remove the screw, then carefully pull SSD card. Step 3 Take out SSD Card bracket.
Step 4. You can replace SSD card by unscrewing 4 screws as shown in the picture. Note: 4 screws are packed in the packing list. Step 5 There is a SD card hole in the side of the machine. You can replace SD card from there. Step 6. Gently screw the screws.
1.5 Installation of HDD (ARCHMI-710) Step 1 There are 2 screws to deal with when enclosing or removing the chassis. Gently remove 2 screws. Step 2 Take the storage cover beside the Panel PC. Step 3 You can put or remove HDD into the machine by pulling the HDD bracket.
Step 4. There is a SD hole in the side of machine. You can replace SD card from there. 1.6 Installation of HDD (ARCHMI-712/ARCHMI-715) Step 1 There are 2 screws to deal with when enclosing or removing the chassis. Gently remove 2 screws. Step 2 You can put or remove HDD into the machine by pulling the HDD bracket.
Step 3 You can remove HDD by unscrewing 4 screws in the HDD bracket. Note: 4 screws are packed in the packing package. Step 4 There is a SD hole in the side of machine. You can replace SD card from there.
Chapter 2 Hardware 2.1 Mainboard Specifications Board Size 170mm x 113mm CPU Support Intel Atom N2600 /1.60GHz (2cores,3.5W, onboard） Intel Atom D2550 /1.
Digital I/O Battery Audio 8-bit digital I/O by Pin header (CN2) 4-bit digital Input 4-bit digital Output 4-bit digital I/O byLiPin header Support CR2477 battery by(CN3) 2-pin header 2-bit digital Input Support Audio via Realtek ALC662 HD audio codec 2-bit digital Output Support Line-in, Line-out, MIC by 2x6-pin header Keyboard /Mouse 1 x PS2 keyboard/mouse by 1x6 box pin header (CN3) Expansion Bus 1 x mini-PCI-express slot 1 x PCI-express (CN3) Touch Ctrl 1 x Touch ctrl header for TCH1 (COM4) Power
(units :mm) Figure 2.
2.2 Introduction SBC-7106 is a 4" industrial motherboard developed on the basis of Intel Cedarview-M Processors and NM10, which provides abundant peripheral interfaces to meet the needs of different customers. Also, it features dual GbE ports, 3-COM ports and one Mini PCIE configuration,one VGA port, one HDMI port, one LVDS interface. To satisfy the special needs of high-end customers, CN1 and CN2 and CN3 richer extension functions. The product is widely used in various sectors of industrial control. 2.2.
Board Bottom Figure 2.
2.3 Jumpers Setting and Connectors 1. JP5: (2.0mm Pitch 1X2 box Pin Header),ATX Power and Auto Power on jumper setting. JP5 Mode Open ATX Power Close Auto Power on (Default) 2. JP3: (2.0mm Pitch 1X2 Pin Header)CMOS clear jumper, CMOS clear operation will permanently reset old BIOS settings to factory defaults. a) b) c) d) e) JP3 CMOS Open NORMAL (Default) Close 1-2 Clear CMOS Procedures of CMOS clear: Turn off the system and unplug the power cord from the power outlet.
Model DC_IN1 SBC-7106-N2600 180°Connector SBC-7106-N2600-P 45°Connector SBC-7106-D2550 45°Connector 5. CPU_FAN1: (2.54mm Pitch 1x3 Pin Header),Fan connector, cooling fans can be connected directly for use. You may set the rotation condition of cooling fan in menu of BIOS CMOS Setup. Pin# Signal Name 1 Ground 2 VCC 3 Rotation detection Note: Output power of cooling fan must be limited under 5W. Model CPU_FAN1 SBC-7106-N2600 No SBC-7106-N2600-P No SBC-7106-D2550 Yes 6. VGA1: (CRT 2.
7. HDMI1: (HDMI 19P Connector), High Definition Multimedia Interface connector. 8. JP1: (2.0mm Pitch 2x3 Pin Header),COM1 jumper setting, pin 1~6 are used to select signal out of pin 9 of COM1 port. JP1 Pin# Function Close 1-2 COM1 RI (Ring Indicator) (default) Close 3-4 COM1 Pin9=+5V (option) Close 5-6 COM1 Pin9=+12V (option) 9. S_232: (Switch),COM1 jumper setting, it provides selectable RS232 or RS422 or RS485 serial signal output.
Step 2: Remove the storage cover Step 3: Unscrew the storage tray Step 4: Remove the storage tray 29
Step 5: The function switch setting shows up 10. S_422: (Switch), COM1 setting, it provides selectable RS232 or RS422 or RS485 serial signal output. Function S_422 Pin# RS232 (Default) OFF: RS422 (option) ON: RS485 (option) ON: Pin1, Pin2, Pin3, Pin4 Pin1, Pin2, Pin3, Pin4 Pin1, Pin2, Pin3, Pin4 11. COM1: (Type DB9),Rear serial port, standard DB9 Male serial port is provided to make a direct connection to serial devices. COM1 port is controlled by pins No.
RS232 (Default): Pin# Signal Name 1 DCD# (Data Carrier Detect) 2 RXD (Received Data) 3 TXD (Transmit Data) 4 DTR (Data Terminal Ready) 5 Ground 6 DSR (Data Set Ready) 7 RTS (Request To Send) 8 CTS (Clear To Send) 9 JP1 select Setting (RI/5V/12V) BIOS Setup： Advanced/W83627UHG Super IO Configuration/Serial Port 1 Configuration【RS-232】 RS422 (option): Pin# Signal Name 1 422_RX+ 2 422_RX- 3 422_TX- 4 422_TX+ 5 Ground 6 NC 7 NC 8 NC 9 NC BIOS Setup： Advanced/W83627UHG Sup
12. JP2: (2.0mm Pitch 2x3 Pin Header),COM2 jumper setting, pin 1~6 are used to select signal out of pin 9 of COM2 port. JP2 Pin# 13. Function Close 1-2 COM2 RI (Ring Indicator) (default) Close 3-4 COM2 Pin9=+5V (option) Close 5-6 COM2 Pin9=+12V (option) COM2: (Type DB9),Rear serial port, standard DB9 Male serial port is provided to make a direct connection to serial devices. Pin# 14.
16. LED3: LED STATUS. Green LED for Touch Power status. 17. SATA_P: (2.5mm Pitch 1x2 box Pin Header), Two onboard 5V output connectors are reserved to provide power for SATA devices. Pin# Signal Name 1 +DC5V 2 Ground Note: Output current of the connector must not be above 1A. 18. SATA2: (SATA 7Pin), SATA Connectors, one SATA connectors are provided, with transfer speed up to 3.0Gb/s. 19. SATA1: (SATA 7Pin+15Pin), SATA Connectors, one SATA connectors are provided, with transfer speed up to 3.
24. USB45: USB4/USB5：(Double stack USB type A), Rear USB connector, it provides up to 4 USB2.0 ports, High-speed USB 2.0 allows data transfers up to480 Mb/s ,support USB full-speed and low-speed signaling. Each USB Type A Receptacle (2 Ports) Current limited value is 1.5A. If the external USB device current exceeds 1.5A, please separate connectors into different Receptacle. 25. LAN1/LAN2: LAN1/LAN2: (RJ45 Connector), Rear LAN port, Two standard 10/100/1000M RJ-45 Ethernet ports are provided.
LA_DATAP1 16 15 LA_DATAN1 LA_DATAP2 18 17 LA_DATAN2 LA_DATAP3 20 19 LA_DATAN3 LA_CLKP 22 21 LA_CLKN Ground 24 23 Ground Ground 26 25 Ground USB1 USB1_P 28 27 USB1_N USB1 USB0 USB0_P 30 29 USB0_N USB0 5V_USB01 32 31 5V_USB01 USB1 5V_USB01 34 33 5V_USB01 PWR_LED+ 36 35 HDD_LED+ Ground 38 37 Ground PWRBTN_ON- 40 39 FP_RST- PWR LED PWR ON/OFF HDD LED RESET INVT1： (2.0mm Pitch 1x6 Pin wafer connector), Backlight control connector for LVDS.
COM3 BIOS Setup： Advanced/W83627UHG Super IO Configuration/Serial Port 3 Configuration 【RS-422】 Advanced/W83627UHG Super IO Configuration/Serial Port 3 Configuration 【RS-485】 31. CN3: (1.27mm Pitch 2X30 Pin Header), For expand output connector, It provides four GPIO, Two USB 2.0,one PS/2 mouse，one PS/2 keyboard,two uart,one PCIe x1,one SMbus. connected to the TB-528 riser Card.
33. H1/H2: MPCIE1 SCREW HOLES, H1and H2 for mini PCIE card (30mmx30mm) assemble. 34. TB-528C2ME1（option）: SBC-7106 Riser Card,TB-528C2ME1 CN3 connect to SBC-7106 CN3 pin Header. TB-528C2ME1 Top： CN3： (1.27mm Pitch 2X30 Pin Header),connect to SBC-7106 CN3 pin Header. M-PCIE1： (Socket 52Pin),mini PCIe socket, it is located at the top, it supports mini PCIe devices with USB2.0(USB2),Smbus,SIM and PCIe signal. MPCIe card size is 30x30mm or 30x50.95mm. Signal Name Function support PCIe 1X Yes USB2.
Pin# Signal Name 1 KBDATA 2 MSDATA 3 Ground 4 +5V 5 KBCLK 6 MSCLK GPIO1： (2.0mm Pitch 2x5 Pin Header),General-purpose input/output port, it provides a group of self-programming interfaces to customers for flexible use. Signal Name Pin# Pin# Signal Name Ground 1 2 NC NC 3 4 SMB_DATA_R SMB_CLK_R 5 6 ICH_GPIO13_IN1 ICH_GPIO24_IN2 7 8 ICH_GPIO26_IN3 ICH_GPIO27_IN4 9 10 +5V USB_23： (2.
or 5V or 12v, For details, please refer to description of JP3. Pin# Signal Name 1 DCD# (Data Carrier Detect) 2 RXD (Received Data) 3 TXD (Transmit Data) 4 DTR (Data Terminal Ready) 5 Ground 6 DSR (Data Set Ready) 7 RTS (Request To Send) 8 CTS (Clear To Send) 9 JP5 Setting: Pin1-2 : RI (Ring Indicator) Pin3-4 : 5V Standby power Pin5-6:12V Standby power (default) (option) (option) JP6： (2.
8 CTS (Clear To Send) 9 JP6 Setting: Pin1-2 : RI (Ring Indicator) Pin3-4 : 5V Standby power Pin5-6:12V Standby power (default) (option) (option) COM_6（option）： (2.0mm Pitch 2X5 Pin Header),COM6 Port, up to one standard RS232 port are provided. They can be used directly via COM cable connection. 35.
Pin# Signal Name 1 KBDATA 2 MSDATA 3 Ground 4 +5V 5 KBCLK 6 MSCLK GPIO1： (2.0mm Pitch 2x5 Pin Header),General-purpose input/output port, it provides a group of self-programming interfaces to customers for flexible use. Signal Name Pin# Pin# Signal Name Ground 1 2 NC NC 3 4 SMB_DATA_R SMB_CLK_R 5 6 ICH_GPIO13_IN1 ICH_GPIO24_IN2 7 8 ICH_GPIO26_IN3 ICH_GPIO27_IN4 9 10 +5V USB_23： (2.
serial devices. COM5 port is controlled by pins No.1~6 of JP5,select output Signal RI or 5V or 12v, For details, please refer to description of JP3. Pin# Signal Name 1 DCD# (Data Carrier Detect) 2 RXD (Received Data) 3 TXD (Transmit Data) 4 DTR (Data Terminal Ready) 5 Ground 6 DSR (Data Set Ready) 7 RTS (Request To Send) 8 CTS (Clear To Send) 9 JP5 Setting: Pin1-2 : RI (Ring Indicator) Pin3-4 : 5V Standby power Pin5-6:12V Standby power (default) (option) (option) JP6： (2.
8 CTS (Clear To Send) 9 JP6 Setting: Pin1-2 : RI (Ring Indicator) Pin3-4 : 5V Standby power Pin5-6:12V Standby power (default) (option) (option) COM_6（option）： (2.0mm Pitch 2X5 Pin Header),COM6 Port, up to one standard RS232 port are provided. hey can be used directly via COM cable connection. 36.
USB2.0 (USB2) NC (option) SMBus Yes SIM Yes H1/H2: MPCIE1 SCREW HOLES, H2 for mini PCIE card (30mmx30mm) assemble. H1 for mini PCIE card (30mmx50.95mm) assemble. LED1： Mini PCIe devices LED Status. SIM1（option）： (SIM Socket 6 Pin), Support SIM Card devices. PS_ON1： (2.0mm Pitch 1X2 Pin Wafer), ATX Power and Auto Power on jumper setting. PS_ON Close 1-2 Open 1-2 Mode Auto Power on (Default) ATX Power PS_ON2（option）： (2.
Signal Name Pin# Pin# Signal Name Ground 1 2 NC NC 3 4 SMB_DATA_R SMB_CLK_R 5 6 ICH_GPIO13_IN1 ICH_GPIO24_IN2 7 8 ICH_GPIO26_IN3 ICH_GPIO27_IN4 9 10 +5V USB23： (Double stack USB type A), Rear USB connector, it provides up to 2 USB2.0 ports, speed up to 480Mb/s. USB_23（option）： (2.0mm Pitch 2x5 Pin Header) ,Front USB connector, it provides one USB port via a dedicated USB cable, speed up to 480Mb/s.
Pin# Signal Name 1 DCD# (Data Carrier Detect) 2 RXD (Received Data) 3 TXD (Transmit Data) 4 DTR (Data Terminal Ready) 5 Ground 6 DSR (Data Set Ready) 7 RTS (Request To Send) 8 CTS (Clear To Send) 9 JP5 Setting: Pin1-2 : RI (Ring Indicator) Pin3-4 : 5V Standby power Pin5-6:12V Standby power (default) (option) (option) JP6： (2.0mm Pitch 2x3 Pin Header),COM6 setting jumper, pin 1~6 are used to select signal out of pin 9 of COM6 port.
9 JP6 Setting: Pin1-2 : RI (Ring Indicator) Pin3-4 : 5V Standby power Pin5-6:12V Standby power (default) (option) (option) S1： PWR BT: POWER on/off Button, They are used to connect power switch button. The two pins are disconnected under normal condition. You may short them temporarily to realize system startup & shutdown or awaken the system from sleep state. PWR LED: POWER LED status. 37.
SMBus Yes SIM Yes H1/H2: MPCIE1 SCREW HOLES, H2 for mini PCIE card (30mmx30mm) assemble. H1 for mini PCIE card (30mmx50.95mm) assemble. LED1： Mini PCIe devices LED Status. SIM1（option）： (SIM Socket 6 Pin), Support SIM Card devices. PS2： (2.0mm Pitch 1X6 Pin Wafer), PS/2 keyboard and mouse port, the port can be connected to PS/2 keyboard or mouse via a dedicated cable for direct used. Pin# Signal Name 1 KBDATA 2 MSDATA 3 Ground 4 +5V 5 KBCLK 6 MSCLK USB_IN（option）： (2.
PSON_ATX 7 8 Ground PSON_ATX 9 10 Ground JP6： (2.0mm Pitch 2x3 Pin Header),COM6 setting jumper, pin 1~6 are used to select signal out of pin 9 of COM6 port. JP3 Pin# Function Close 1-2 RI (Ring Indicator) (default) Close 3-4 COM6 Pin9=+5V (option) Close 5-6 COM6 Pin9=+12V (option) COM6： (2.0mm Pitch 2X5 Pin Header),COM6 Port, up to one standard RS232 port are provided. They can be used directly via COM cable connection.
JTAG： (2.0mm Pitch 2x5 Pin Header), Reserve. JP1： (2.0mm Pitch 1x2 Pin Header), Reserve. JP2： (2.0mm Pitch 1x2 Pin Header), Reserve. CAN12： (3.5mm Pitch 1x10 Pin connector), it provides two CAN-bus Interface.
Chapter 3 BIOS Setup 3.1 Operations after POST Screen After CMOS discharge or BIOS flashing operation,.Press [Delete] key to enter CMOS Setup. After optimizing and exiting CMOS Setup, the POST screen displayed for the first time is as follows and includes basic information on BIOS, CPU, memory, and storage devices. 3.2 BIOS Setup Utility Press [Delete] key to enter BIOS Setup utility during POST, and then a main menu containing system summary information will appear.
3.
Minute : 0 to 59 Second : 0 to 59 System Date: Set the system date, the date format is: Day: Note that the ‘Day’ automatically changes when you set the date. Month: 01 to 12 Date: 01 to 31 Year: 1998 to 2099 3.4 Advanced Settings 3.4.1 PCI Subsystem Settings PCI Bus Driver Versio V2.05.
[248 PCI Bus Clocks] VGA Palette Snoop: [Disabled] [Enabled] PERR# Generation: [Disabled] [Enabled] SERR# Generation: 3.4.
3.4.3 CPU Configuration Processor Type Intel(R) Atom(TM) CPU N2600 EMT64 Not Supported Processor Speed 1600MHz System Bus Speed 400MHz Ratio Status 16 Actual Ratio 16 System Bus Speed 400MHz Processor Stepping 30661 Microcode Revision 269 L1 Cache RAM 2x56 k L2 Cache RAM 2x512 k Processor Core Dual Hyper-Threading Supported Hyper-Threading: [Enabled] [Disabled] Execute Disable Bit: [Enabled] [Disabled] Limit CPUID Maximum: [Disabled] [Enabled] 3.4.
SATA Port1 Not Present SATA Controller(S): [Enabled] [Disabled] Configure SATA as: [IDE] [AHCI] Misc Configuration for hard disk 3.4.
3.4.7 W83627UHG Super IO Configuration W83627UHG Super IO ch W83627UHG Serial Port 1 Configuration UART Mode Selection： [RS-232] [RS-485] [RS-422] Serial Port 2 Configuration Serial Port 3 Configuration UART Mode Selection： [RS-485] [RS-422] Serial Port 4 Configuration Serial Port 5 Configuration Serial Port 6 Configuration 3.4.8 3.4.9 W83627UHG HW Monitor PC Health Status System Temperature1 : +38 System Speed : N/A VCORE : +0.968V +12V : +12.302V +3.3V : +3.320V +1.5V : +1.528V AVCC : +5.
3.4.
3.5 Chipset Settings 3.5.
[Disabled] Max TOLUD [Dynamic] [1GB] [1.25GB] [1.5GB] [1.75GB] [2GB] [2.25GB] [2.5GB] [2.75GB] [3GB] [3.
[Maintain Aspect Ratio] Active LFP [LVDS] [No LVDS] [EDP] IGD Clock Source [External Clock] [Internal Clock] Fixed Graphics Memory [128MB] [256MB] ALS Support [Disabled] [Enabled] Back light Control [DC] [PWM] Back light Logic [Positive] [Negative] Back light Control Lev [Auto] [Disabled] [Level 8] [Level 1] [Level 2] [Level 3] [Level 4] [Level 5] [Level 6] [Level 7] [Level 8] [Level 9] [Level 10] [Level 11] [Level 12] [Level 13] [Level 14] [Level 15] 3.5.
[Enabled] [Disabled] PCI-Exp. High Priorit [Disabled] [Enabled] High Precision Event Timer Configuration High Precision Timer [Enabled] [Disabled] SLP_S4 Assertion Widt [1-2 Seconds] [2-3 Seconds] [3-4 Seconds] [4-5 Seconds] 3.
Setup Prompt Timeout Bootup Numlock State [1] [On] [off] Quiet Boot [Disabled] [Enabled] Fast Boot [Enabled] [Disabled] Skip VGA [Enabled] [Disabled] Skip USB [Disabled] [Enabled] Skip PS2 [Disabled] [Enabled] CSM16 Module Version Gatea20 Active 07.
[UEFI only] Launch PXE OpROM poli [Do not Launch] [UEFI only] [Legacy only] Launch Storage OpROM [Legacy only] [Do not Launch] [UEFI only] Launch Video OpROM po [Do not Launch] [UEFI only] [Legacy only] Other PCI device ROM [UEFI OpROM] [Legacy OpROM] 3.7 Security Settings 3.7.1 Administrator Password 3.7.
Type the password with up to 20 characters and then press key. This will clear all previously typed CMOS passwords. You will be requested to confirm the password. Type the password again and press key. You may press key to abandon password entry operation. To clear the password, just press key when password input window pops up. A confirmation message will be shown on the screen as to whether the password will be disabled.
Save Changes and Exit Save & Exit Setup save Configuration and exit ? [Yes] [No] Discard Changes and Ext Exit Without Saving Quit without saving? [Yes] [No] Save Changes and Reset Save & reset Save Configuration and reset? [Yes] [No] Discard Changes and Reset Reset Without Saving Reset without saving? [Yes] [No] Save Changes Save Setup Values Save configuration? [Yes] [No] Discard Changes Load Previous Values Load Previous Values? [Yes] [No] Restore Defaults Load Optimized Defaults Load optimized Defaults?
Chapter 4 Installation of Drivers This chapter describes the installation procedures for software and drivers under the windows 7. The software and drivers are included with the motherboard. The contents include Intel chipset driver, VGA driver, LAN drivers, Audio driver Installation instructions are given below. Important Note: After installing your Windows operating system, you must install first the Intel Chipset Software Installation Utility before proceeding with the installation of drivers.
4.1 Intel Chipset Driver To install the Intel chipset driver, please follow the steps below. Step 1. Select Intel (R) Chipset NM10 Express from the list Step 2. Click Next to setup program.
Step 3. Read the license agreement. Click Yes to accept all of the terms of the license agreement. Step 4. Click Next to continue.
Step 5. Click Next. Step 6. Select Yes, I want to restart this computer now. media from the drives.
4.2 Intel Graphics Media Accelerator Driver To install the VGA drivers, follow the steps below to proceed with the installation. Step 1.Select Intel(R) VGA Chipset Driver. Step 2. Tick Automatically run WinSAT and enable the Windows Aero desktop theme(if supported). Click Next.
Step 3. Read license agreement. Click Yes. Step 4. Click Next.
Step 5. Click Next. Step 6. To restart the computer, select Yes, I want to restart this computer now. Then click Finish.
4.3 Intel (R) Network Adapter To install the Intel (R) Network Adapter device driver, please follow the steps below. Step 1. Select LAN Driver. Step 2. Select ARCHMI-7”~15”.
Step 3. Click Next to continue. Step 4. Click Install to begin the installation.
Step 5. Click Finish to exist the wizard. 4.4 Realtek ALC662 HD Audio Codec Driver Installation To install the Realtek ALC662 HD Audio Codec Driver, please follow the steps below. Step 1.
Step 2. Click Next to continue. Step 3. Click Yes, I want to restart my computer now. ARCHMI-7XX User Manual Click Finish to complete the installation.
Chapter 5 Touch Screen Installation This chapter describes how to install drivers and other software that will allow your touch screen work with different operating systems. 5.1 Windows 2000/2003/Vista/WIN7 Universal Driver Installation for PenMount 6000 Series Before installing the Windows 2000/WIN7 driver software, you must have the Windows 2000/WIN 7 system installed and running on your computer.
Step 2. Select Resistive Touch. Step 3. Click Next to continue.
Step 4. Read the license agreement. Click I Agree to agree the license agreement. Step 5. Choose the folder in which to install PenMount Windows Universal Driver. Click Install to start the installation.
Step 6. Wait for installation. Then click Next to continue. Step 7. Click Continue Anyway.
Step 8. Click Finish to complete installation. 5.1.2 Installing Software (Projected Capacitive) Step 1. Insert the product CD, the screen below would appear. Click Touch Panel Driver.
Step 2. Select Projected Capacitive. Step 3. Click Next to continue.
Step 4. Select I accept the terms of the license agreement. Step 5. Tick Install RS232 interface driver. ARCHMI-7XX User Manual Click Next. Click Next.
Step 6. Select None. Click Next. Step 7. Click OK. Step 8. Tick Support Muti-Monitor System. ARCHMI-7XX User Manual Click Next.
Step 9. Go to C:\Program Files\eGalaxTouch. Click Next. Step 10. Click Next.
Step 11. Tick Create a eGalaxTouch Utility shortcut on desktop. Click Next. Step 12. Wait for installation.
Step 13. Click Yes to do 4 point calibration. 5.2 Software Functions 5.2.1 Software Functions(Resistive Touch) Upon rebooting, the computer automatically finds the new 6000 controller board. The touch screen is connected but not calibrated. Follow the procedures below to carry out calibration. 1. After installation, click the PenMount Monitor icon “PM” in the menu bar. 2. When the PenMount Control Panel appears, select a device to “Calibrate.
Standard Calibration Click this button and arrows appear pointing to red squares. Use your finger or stylus to touch the red squares in sequence. After the fifth red point calibration is complete. To skip, press ‘ESC’. Advanced Calibration Advanced Calibration uses 4, 9, 16 or 25 points to effectively calibrate touch panel linearity of aged touch screens. Click this button and touch the red squares in sequence with a stylus. To skip, press ESC’. Command Calibration Command call calibration function.
Step 2.Click “Standard Calibration” to start calibration procedure NOTE: The older the touch screen, the more Advanced Mode calibration points you need for an accurate calibration. Use a stylus during Advanced Calibration for greater accuracy.
Step 3.Come back to “PenMount Control Panel” and select Tools then click Advanced Calibration. Step 4. Select Device to calibrate, then you can start to do Advanced Calibration. NOTE: Recommend to use a stylus during Advanced Calibration for greater accuracy.
Plot Calibration Data Check this function and a touch panel linearity comparison graph appears when you have finished Advanced Calibration. The blue lines show linearity before calibration and black lines show linearity after calibration. Turn off EEPROM storage The function disable for calibration data to write in Controller. The default setting is Enable. Setting Touch Mode This mode enables and disables the mouse’s ability to drag on-screen icons – useful for configuring POS terminals.
About This panel displays information about the PenMount controller and driver version.
Multiple Monitors Multiple Monitors support from two to six touch screen displays for one system. The PenMount drivers for Windows 2000/WIN 7 support Multiple Monitors. This function supports from two to six touch screen displays for one system. Each monitor requires its own PenMount touch screen control board, either installed inside the display or in a central unit. The PenMount control boards must be connected to the computer COM ports via the RS-232 interface.
3. Touch each screen as it displays “Please touch this monitor”. Following this sequence and touching each screen is called mapping the touch screens. 4. Touching all screens completes the mapping and the desktop reappears on the monitors. 5. Select a display and execute the “Calibration” function. A message to start calibration appears. Click OK. 6. ”Touch this screen to start its calibration” appears on one of the screens. Touch the screen. 7. “Touch the red square” messages appear.
NOTES: 1. If you use a single VGA output for multiple monitors, please do not use the Multiple Monitor function. Just follow the regular procedure for calibration on each of your desktop monitors. 2. The Rotating function is disabled if you use the Multiple Monitor function. 3. If you change the resolution of display or screen address, you have to redo Map Touch Screens, so the system understands where the displays are.
Control Panel Open Control Panel Windows Beep Setting Beep function for each device Right Button When you select this function, a mouse icon appears in the right-bottom of the screen. Click this icon to switch between Right and Left Button functions. Exit Exits the PenMount Monitor function. PenMount Rotating Functions The PenMount driver for Windows 2000/WIN7 supports several display rotating software packages.
Monitor Mapping To adjust touch panel Add To search for device ARCHMI-7XX User Manual 98
Setting Beep Beep On Touch Beep On Release Beep From System Beep Beep From Sound Card Linearization Style 9 points 25 points Double Click Time Shorter Longer Double Click Area Smaller Bigger Normal mode Simulate the mouse mode ARCHMI-7XX User Manual 99
Option Function Enable Constant Touch Enable Auto Right Click Enable Touch Enable Cursor Stabilization Constant Touch Area Auto Right Click Time ARCHMI-7XX User Manual 100
Tools Click OK to continue the settings. 4 Points Calibration Do 4 points alignment to match display. Clear and Calibrate Clear linearization parameter and do 4 points alignment. Linearization Do 9 points linearization for better touchscreen linearity. Draw Test Do draw test to verify the touch accuracy.
Display In this window, it shows the mode of display. Enable Multiple Monitors.
Other Other mode of display. Quarter1~4 and Customized area. Active Area Drag active area to enable Active Area Function.
Hardware Saturn Hardware Configuration ARCHMI-7XX User Manual 104
About To display information about eGalaxTouch and its version.
