User's Manual

【MOTION SENSOR SENSING RANGE】
The range of the motion sensor is affected by the sensor
orientation and installation height. The sensitivity of the
sensor will also vary due to factors such as the brightness
and temperature changes in the surrounding environment.
In addition, the speed of the person approaching the sensor
will have an effect on when the light will turn on.
Factors that may affect the motion sensor function are:
1. Approach from directly in front of the motion sensor.
2. The temperature difference between the ambient and
human body is small. (For example: high temperature in
summer)
3. Body temperature is not easy to detect. (For example:
wearing heavy clothes)
Replace the battery if the following conditions occur:
● Red indicator keeps flashing
● LED light is bright but dim
● LED light does not light up
● Light-up time becomes shorter
※ When replacing the batteries be certain to replace ALL the batteries
with new batteries.
※ If the lights are placed in an area where they are frequently turned on
and off. The battery life will be shorter than advertised.
※ The motion sensors respond to temperature changes in the sensing area
causing the light to turn on. Therefore pets can activate the lights
which can also have an effect on battery life.
【LIGHTING ZONE SETUP】 【HOW TO SET】
This product uses 2.4 GHz wireless communication
transmission to link each device. The maximum
transmission distance is about 20m (65ft). When the
ambient light is dark, the device that detects the
motion will send a signal to link all other devices
* within 20m (65 ft), if no interference shelter and
* set with the same lighting zone
for activation.
The reason for setting the lighting zone is to avoid
that the lighting area has nothing to do with the
direction of travel, so as to save battery power. This
device can create up to 3 lighting zones. The color of
the setting button can be divided into blue (factory
setting), green and white. Devices set to the same
color can communicate with each other. The lighting
zone set by the user will be retained after the new
battery is replaced- NO need to reset.
※ The wireless transmission distance may be
shortened due to different use environments such as
shelters or building structures.
1. Press the "lighting zone button" on the back of the
device within 3 seconds to change the color of the
"lighting zone indicator".
2. After setting the color, the selected color (light) will be
on for 3 seconds and then flash 3 times, indicating that
the setting is complete.
【INSTALLATION】
Please read the instruction carefully before use, and keep it in a safe place for reference.
※ Do not place any objects between wall lights to avoid interference of wireless transmission.
※ Since the ambient conditions of the mounting area will affect the function of the lights. Check to make sure there are no problems in the mounting area before use.
※ When the backplate cannot be attached to the wall by mounting screws, the supplied double sided tape can be used.
Please note that the mounting surface must be clean and smooth for best results. Do not apply to rough or peeling walls.
※ The double sided tape has a strong adhesive on both sides. It is very easy to damage the wall when the light is removed.
Please use caution during installation and removal as the responsibility for wall damage falls on the installer.
【TROUBLESHOOTING】
There are people in the sensing area of the
light but the light will not turn on.
1. Are the lights installed in a bright area?
2. Are the batteries installed correctly?
3. Is the battery power low?
4. Is the room temperature very low? Or are the
people wearing heavy clothing?
5. Is the person being still and not moving?
1. When the surroundings are bright, the motion sensor is in
sleep mode. Wait until the surroundings become dark or
move to a darker place for inspection.
2. Please confirm that the battery's positive (+) and negative
(-) poles are installed in the correct direction.
3. Replace the battery.
4. The operating principle of the sensor is to respond to
temperature changes caused by the movement of the human
body, so it is not easy to detect temperature differences
under these conditions.
5. If the person in the sensing area is not moving, they will
not be detected by the sensor.
LED Light will not turn off. 1. Is anyone in the sensing area?
2. Is the battery low?
1. Leave the sensing area or keep still.
2. Replace the battery.
There is no one in the sensing area of the
motion sensor, but the light is on.
Is there a heat source or moving objects in the
sensing area?
Remove the heat source or move light also remove any
moving objects in the sensing area.
※ The specifications and appearance of this device may be changed without notice due to improvements.