Specification

ManualsBrandsApollo ManualsPlumbing3/4 in. x 3/4 in. Lead Free Bronze FNPT Pressure Reducing Valve with Gauge

SUBMITTAL SHEET

69ELF Series

Pressure Reducing Valve

with Gauge

VALVES

The Apollo® Lead Free* Double Union Pressure Reducing Valve Model PRE (69ELF

Series) is designed to conserve water and protect water distribution systems by

automatically reducing elevated supply pressures. The dezincication resistant

bronze body, stainless steel adjusting screw and dielectric polymer cage provide

maximum corrosion resistance. Designed for easy in-line servicing with simple

cartridge removal. With simple adjustability and an instant read, color-coded dial to

provide downstream pressure measurement, this valve solves all of the annoyances

of pressure regulators from the past. It also assists in the control of pressure surges

from entering the structure from the water main to further protect xtures and

appliances. Excessive high pressure within a polumbing system can cause damage

over time.

Specications:

The PRV is designed to reduce pressure to a more functional level within its adjustment range. A

gauge must be used to verify setting. To increase the set pressure, turn the handle clockwise. To

decrease the set pressure, turn the handle counter-clockwise. Open a fixture to purge excess pressure,

then verify setting. Allow for some fall-off from set pressure during flow conditions.

Features:

• Balanced Piston Design • SS Adjusting Screw & Nut

• Sealed Cage for vault installations • Built-in Thermal Expansion Bypass

• Large Area Integral Stainless Steel Strainer • Modular Seat Disc and Strainer Cartridge

• High Flow / high eciency design • Factory Tested and Preset at 60 psi

• NPT, Solder, PEX, CPVC, Push & Press Connections • 100% Manufactured in USA –

• Control Pressure Ranges: 15-75 psi and 75-150 psi ARRA Compliant

• Single Union, Double Union and Less Union Congurations Available

Approvals:

• NSF/ANSI 372 Lead Free • NSF/ANSI 61 Water Quality

• ASSE 1003 • IAPMO/UPC

• CSA B356

Installation:

Prior to installing the Pressure Reducing Valve (PRV), all debris must be flushed from the line. Isolate

the section where the PRV is to be installed by closing the shut-off valves. The PRV is designed to be

installed in a piping system with the arrow on the valve pointing in the direction of flow. It can be

mounted vertically or horizontally.

*LEAD FREE: The wetted surfaces of this product shall contain no more than 0.25% lead by weighted average. Complies with Federal Public Law 111-380. ANSI 3rd party

approved and listed.

Job Name:

Job Location:

Engineer:

Contractor:

Tag:

PO Number:

Representative:

Standard Materials List:

Body: Lead Free* Bronze, UNS 89836

Union Nut: Brass, ASTM B16

Tailpiece: Lead Free* Brass, UNS C27451

Screen: Stainless Steel

Cap: Noryl™

Diaphragm: NSF-Grade EPDM

Seat Disc: NSF-Grade EPDM

Adjusting Screwnut: Stainless Steel

Spring: Stainless Steel, ASTM A228

O-Rings: NSF-Grade EPDM

Performance Rating:

• Maximum Supply Pressure: 400 psig

• Working Temperature Range: 33°F – 180°F

Summary of content (2 pages)

PAGE 1
VALVES SUBMITTAL SHEET Job Name: 69ELF Series Engineer: Job Location: Pressure Reducing Valve with Gauge Contractor: Tag: PO Number: Representative: The Apollo® Lead Free* Double Union Pressure Reducing Valve Model PRE (69ELF Series) is designed to conserve water and protect water distribution systems by automatically reducing elevated supply pressures. The dezincification resistant bronze body, stainless steel adjusting screw and dielectric polymer cage provide maximum corrosion resistance.
PAGE 2
VALVES PEX-A Installation: 1. Cut pipe squarely and place expansion sleeve on end. 2. Insert expansion tool head into tubing and expand. 3. Immediately remove tool and insert valve end into pipe to shoulder. Pipe may take up to two minutes to fully seal. PEX CPVC PEX A FNPT PRESS PEX-B Installation: 1. Cut pipe squarely and remove any burrs. 2. Slide ring, clamp or sleeve over end of pipe. 3. Insert valve barb end into pipe. 4. Fasten according to tool directions. Push Installation: 1.