Instructions / Assembly

ManualsBrandsApollo ManualsAccessories3/4 in. Copper Crimp Ring Jar (100-Pack)

INSTRUCTION SHEET

PEX

Crimp Tools

PEX

69PTKH00143 - 1/2"

69PTKH00144 - 3/4"

69PTKH0014C - 1/2" & 3/4"

69PTKH0015K - 3/8"-1"

To remove and replace jaws: For 69PTKH0015K only (Jaws cannot be replaced on any other Apollo crimp tools)

1. Cut tubing end squarely. Check for and

remove any burrs.

2. Slide crimp ring over end of tubing.

Insert tting into end of tubing until it

stops. Position the crimp ring 1/8" to

1/4" from the end of the tubing and

over the ribs of the tting.

3. Place the crimping end of tool around

the crimp ring and press the handles

together.

4. Check for proper crimp with the

Go/ No-Go gauge.

1. With the handles. fully

open, press side release

spring upward until the

hook is above the jaw pin.

3. With the side release

spring pressed upward,

slide new jaw into place

and release the spring.

2. Slide jaw out of position

and remove.

2 3

If you have a 69PTKH0015K that does not have spring

loaded jaws, but jaws that are secured with screws, sim-

ply loosen the screws located at the center of the jaws.

Remove the jaws and slide the jaws you need into place.

Replace the screws at the center of the jaws and tighten.

Apollo PEX Crimp Rings

APXCR3810PK 3/8" 10 Pack

APXCR1210PK 1/2" 10 Pack

APXCR1225PK 1/2" 25 Pack

APXCR1250PK 1/2" 50 Pack

APXCR12100JR 1/2" 100 Pack Jar

APXCR3410PK 3/4" 10 Pack

APXCR3425PK 3/4" 25 Pack

APXCR34100JR 3/4" 100 Pack Jar

APXCR15PK 1" 5 Pack

APXCR125PK 1" 25 Pack

Apollo PEX PRO Crimp Rings

APXCR12LT 1/2" 10 Pack

APXCR12LTJR 1/2" 75 Pack Jar

APXCR34LT 3/4" 10 Pack

APXCR34LTJR 3/4" 50 Pack Jar

Summary of content (2 pages)

PAGE 1
PEX INSTRUCTION SHEET 69PTKH00143 - 1/2" 69PTKH00144 - 3/4" 69PTKH0014C - 1/2" & 3/4" 69PTKH0015K - 3/8"-1" PEX Crimp Tools 1. Cut tubing end squarely. Check for and remove any burrs. 2. Slide crimp ring over end of tubing. Insert fitting into end of tubing until it stops. Position the crimp ring 1/8" to 1/4" from the end of the tubing and over the ribs of the fitting. Apollo PEX Crimp Rings 4. Check for proper crimp with the Go/ No-Go gauge. 3.
PAGE 2
PEX INSTRUCTION SHEET PEX Crimp Tool Go/No-Go Gauge 1. Slide the correct slot on the gauge around the crimped ring. 2. If the ring does not fit into the slot at all, then the crimp is a “No-Go”. Adjust the crimping force on the tool and re-crimp the ring. 3. If the ring slides into the slot and stops in the “Go” range at least at one point, then the crimp is good. The ring will not fit the go range all the way around it. 4.