User`s manual
Table Of Contents
- Preliminary remarks
- Introduction
- New functions
- Installation
- Best practice
- Requirements
- Used ports
- Setup
- Upgrade from Apollo 1.3 to Apollo 1.4
- Upgrade from Apollo 1.4 to Apollo 1.4SR1
- Upgrading from Apollo 1.4 to Apollo 1.5
- Upgrading from Apollo 1.5 to Apollo 1.6
- Upgrading from Apollo 1.6 to Apollo 1.7
- Upgrading from Apollo 1.7 to Apollo 1.8
- Upgrading from Apollo 1.8 to Apollo 1.9
- Upgrading the Display Wall configuration
- Control Room Configurator
- Viewer
- Concept
- Apollo 1.9 Viewers
- Limitations
- Memory requirements (minimal RAM size)
- Communication memory
- Requirements
- Steps required to configure the FRG Viewer
- Steps required to configure the Visu Viewer
- Steps required to configure the Cottus Viewer
- Steps required to configure the VNC Viewer
- Steps required to configure the ProViewer
- Steps required to configure the Web Viewer
- Steps required to configure the MPEG Viewer
- Steps required to configure the VTplus Viewer
- Launching Viewer
- Controlling Viewers
- VNC Viewer
- Explorer
- Starting the Explorer
- Explorer User Interface
- Object Tree
- Source Tree View
- Explorer workspace
- Explorer menu bar
- Help menu
- Remote Desktop menu
- Layout Selector menu
- Explorer tool bar
- Device Manager in the Explorer
- Explorer Context Menu
- Drag&Drop functionality
- Layout Editor
- Desktop Server
- Project Backup
- Command Interface
- Device command Interface
- Desktop command Interface
- Viewer command Interface
- Apollo Explorer command interface
- Apollo Layout Editor command interface
- Apollo Layout Selector command interface
- Apollo Remote Desktop command interface
- Apollo Database Convertor command interface
- Apollo Window Detector command interface
- Control Room Bus services
- Control Room Bus
- Serial command interface
- TCPIP command interface
- Application management
- License management
- Time synchronization
- Log file
- Security Provider
- Defining accessGroups
- Configuration of restricted objects
- Permissions
- Restrictions for regions
- Restrictions for layouts
- Restrictions for shortcuts
- Restrictions for advanced menus
- Window Properties|Description
- Window Properties|Sizable
- Window Properties|Always on Top
- Window Properties|Visible
- Edit|Invisible Windows
- Edit|Keyboardinput
- Edit|CommandLine
- Edit|Permissions
- Edit|SaveLayout
- Customized configuration and uninstallation of Apollo
- Soap API Service
- Appendix
- Hotline
7. Explorer
Barco – Apollo – DOC-3197-2 – user's manual – Revision 08 – November 2006
_________________________________________________
271/402
7.11.8.5 Projector
This tab informs about brightness, OnScreen Display und Source Input Selection (firmware 3.x only).
Direct Illumination Sensor
Operation State
Indicates whether the DIS sensor is busy or free
Brightness Target Reached The pre-defined brightness target of the Display Wall is reached by this pro-
jector
Brightness Target
Modify or check the value of the Brightness Target. To use the brightness
target, in case the display wall is controlled by the OCM, the automatic
brightness regulation of the OCM has to be switched off!
Brightness Regulation Active Modify or check the Brightness Regulation (Lumens lock mode). Is always
switched on (also in case the display wall is controlled by the OCM)
Projector On / Off Switch the main power of the projector on or off. A green square indicates
that the projector is running.
Reboot Projector
If Firmware upgrade has been performed, the projector has to be reset Click
on this button the start the rebooting
InfraRed Control Enable or disable controlling the projector with the IR Remote-Control Unit.
Over Temperature Protection
Enabled
Set or check the behavior of the projectors when the temperature limit is
reached. Recommended: enabled. If enabled, the projector shuts down if
the temperature is too high (otherwise the systems might be damaged!)
Message Box Enabled
Set or check if message boxes are displayed (overlaying the application) or
not