Installation Guide

ManualsBrandsAPOLLO ManualsInput Moduleapollo SA4705-703APO Soteria UL Switch Monitor Input or Output Module

Max Standby Current (Pulsing LED)

Max Surge Alarm Current (LEDs on)

Wire Range

12-24 AWG

4.8 mA

2.96 mA

The Switch Monitor I/O Module is a loop-powered device that incorporates a monitored input circuit for

connection to a remote switch alongside a 240 Volt-free relay output. It is mounted with a plastic fascia

plate for use with a UL listed 4” electrical box or dual gang.

Please Note:

• The Switch Monitor I/O Module is designed for

indoor dry

use

only

• The unit must be installed in a dedicated suitable UL listed enclosure, employing only power limited

circuit.

APD0830 / 2021 / ISSUE 3

INSTALLATION GUIDE

SOTERIA UL

SWITCH MONITOR INPUT/OUTPUTMODULE

GENERAL

Part Number SA4705-703APO

Replacement Part Number 55000-859, 55000-785, 55000-820

Type Switch Monitor Input/Output Module

Dimensions 4.9” width x 4.9” height x 1.175” depth

Temperature Range 32°F to 120°F (0°C to 49 °C)

Humidity 0 to 95% RH (Non-Condensing)

Signal Line Circuit (SLC) Supervised

Operating Voltage 17-28 V DC

Modulation Voltage

Supervisory Current

LED Current

Maximum Loop Current

Approvals

Material

5-9 V (peak to peak)

<700 µA

1.6 mA per LED

UL, ULC, CSFM, FM

UL 94 V-0

TECHNICAL INFORMATION

All data is supplied subject to change without notice. Speciﬁcations are typical at 24V, 25°C and 50% RH

unless otherwise stated.

CONTROL PANEL COMPATIBILITY

The Switch Monitor I/O Module has been approved by UL, LLC. For details of compatible panels

contact Apollo America Inc. For relay compatibility contact the Panel manufacturer

Summary of content (8 pages)

PAGE 1
APD0830 / 2021 / ISSUE 3 INSTALLATION GUIDE SOTERIA UL SWITCH MONITOR INPUT/OUTPUTMODULE GENERAL The Switch Monitor I/O Module is a loop-powered device that incorporates a monitored input circuit for connection to a remote switch alongside a 240 Volt-free relay output. It is mounted with a plastic fascia plate for use with a UL listed 4” electrical box or dual gang. Please Note: • The Switch Monitor I/O Module is designed for indoor dry use only.
PAGE 2
TECHNICAL INFORMATION COUNT. Initiating Device Circuit (IDC) Supervised power limited Class A and Class B 3.3 V DC (<200 µA) Wiring Styles Voltage Line Impedance 100 Ω max End-of-Line resistors* 47k Ω Note: *A UL listed end-of-line resistor is available at Apollo, Part no. 44251-146 Remarque: * Une résistance de fin de ligne répertoriée UL est disponible chez Apollo, réf.
PAGE 3
(<200 µA) Remarque: * Une résistance de fin de ligne répertoriée UL est disponible chez Apollo, réf. 44251-146 Fig. 1 Fig. 2 WIRING INSTRUCTION Note: ‘X’ denotes unused terminals. Remarque: "X" désigne les terminaux inutilisés. CAUTION – • When Making Installation, Route Field Wiring Away From Sharp Projections, Corners, and Internal Components • A minimum of 1/4 inch space is required between Power Limited and Non-Power Limited circuits while wiring.
PAGE 4
1. 2. 6 a. b. 3. Class B | Fig. 4* Note:* A UL listed end of Line resistor is required in Class B Remarque: * Une résistance de fin de ligne répertoriée UL est requise en classe B Continuité fonctionnelle de la terre. Ne vous connectez pas au backbox. Le blindage doit être scotché pour protéger du court-circuit au boîtier électrique Wiring diagram for shield when shielded cable are used| Fig.
PAGE 5
ADDRESS SETTING Steps: 1. The dip switch used to address your device has 10 individual switches (Figure 6). 2. Address setting is done by dip switches 1-8 (see page 6 for address matrix). a. In XP/Discovery Protocol, only dip switch 1-7 are used, dip switch 8 is used to enable ground fault analogue value. b. Dip switch down = 1 and up = 0. 3. Dip switch 9 is used to set Wiring Class A/B (Figure 7). Remarque: * Une résistance de fin de ligne répertoriée UL est requise en classe B Fig.
PAGE 6
ADDRESS MATRIX 1 1000 0000 43 1101 0100 85 1010 1010 129 1000 0001 171 1101 0101 213 1010 1011 2 0100 0000 44 0011 0100 86 0110 1010 130 0100 0001 172 0011 0101 214 0110 1011 3 1100 0000 45 1011 0100 87 1110 1010 131 1100 0001 173 1011 0101 215 1110 1011 4 0010 0000 46 0111 0100 88 0001 1010 132 0010 0001 174 0111 0101 216 0001 1011 5 1010 0000 47 1111 0100 89 1001 1010 133 1010 0001 175 1111 0101 217 1001 1011 6 0110 0000 48 0000 1100 90 0101 1
PAGE 7
APD0834 20 This page has been intentionally left blank indoor dry use only For NAC circuit, contact Panel manufacturer for compatibility details 1.175 5 Apollo America Inc. 30 Corporate Drive, Auburn Hills, MI 48326 Tel: (248) 332-3900. Fax: (248) 332-8807 Email: info.us@apollo-fire.com www.apollo-fire.com Surge Current 900 µA Max Standby Current (Pulsing LED) Max Alarm Current (Pulsing LED) Wire Range 3.1 mA © 2020 Apollo America Inc.
PAGE 8
APD0834 20 This page has been intentionally left blank indoor dry use only For NAC circuit, contact Panel manufacturer for compatibility details 1.175 5 Apollo America Inc. 30 Corporate Drive, Auburn Hills, MI 48326 Tel: (248) 332-3900. Fax: (248) 332-8807 Email: info.us@apollo-fire.com www.apollo-fire.com Surge Current 900 µA Max Standby Current (Pulsing LED) Max Alarm Current (Pulsing LED) Wire Range 3.1 mA © 2020 Apollo America Inc.