Installation Guide

ManualsBrandsAPOLLO ManualsNAC Moduleapollo SA4705-706APO Soteria UL NAC Module

The NAC Module monitors and controls a circuit of alarm notiﬁcation appliances or speakers. It is

mounted on a plastic face plate for use with a UL listed 4” square or 2 gang electrical box (minimum

depth 2⅛”). The module requires a separate 24V DC supply to power notiﬁcation appliances.

In addition to individual NAC Module operation, multiple modules can be controlled simultaneously as a

group*. A green LED ﬂashes in synchronization with the current pulse reply from the device.

Please Note:

• *Physical group addressing feature is only available in XP95/Discovery Protocol.

• The NAC Module is designed for

indoor dry use only

APD0834 / 2021 / ISSUE 3

INSTALLATION GUIDE

SOTERIA UL

NAC MODULE

GENERAL

Part Number SA4705-706APO

Replacement Part Number 55000-825

Type Sounder Control Module

Dimensions 4.9” width x 4.9” height x 1.175” depth

Temperature Range 32°F to 120°F (0°C to 49 °C)

Humidity 0 to 95% RH (Non-Condensing)

Signal Line Circuit (SLC) Supervised

Operating Voltage 17-28V DC

Modulation Voltage

Supervisory Current

LED Current

Maximum Loop Current

Approvals

Material

TECHNICAL INFORMATION

All data is supplied subject to change without notice. Speciﬁcations are typical at 24V, 25°C and 50% RH

unless otherwise stated.

CONTROL PANEL COMPATIBILITY

The NAC Module has been approved by UL, LLC. For details of compatible panels contact Apollo

America Inc. For NAC circuit, contact Panel manufacturer for compatibility details

Max Standby Current (Pulsing LED)

Max Surge Alarm Current (LEDs on)

5-9 V (peak to peak)

<700 µA

1.6mA per LED

UL, ULC, CSFM, FM

UL 94 V-0

2.96 mA

4.8 mA

Wire Range

12-24 AWG

Summary of content (8 pages)

PAGE 1
APD0834 / 2021 / ISSUE 3 INSTALLATION GUIDE SOTERIA UL NAC MODULE GENERAL The NAC Module monitors and controls a circuit of alarm notification appliances or speakers. It is mounted on a plastic face plate for use with a UL listed 4” square or 2 gang electrical box (minimum depth 2⅛”). The module requires a separate 24V DC supply to power notification appliances. In addition to individual NAC Module operation, multiple modules can be controlled simultaneously as a group*.
PAGE 2
TECHNICAL INFORMATION COUNT. Wiring Styles End-of-Line resistors* External Supply Max (NAC) Max (Speakers) Notification Appliance Circuit (NAC) Supervised power limited Class A and Class B 47k Ω Connected between Vext+ and Vext- Monitored input (DC Voltage Supplies Only) Regulated 24V DC, 2A. Use a regulated power limited dc supply that is listed for fire protection applications. The maximum number of connected devices must be within the output rating. 70.
PAGE 3
Fig. 1 5 WARNING: DISCONNECT POWER BEFORE OPENING Fig. 2 AVERTISSEMENT: COUPER LE COURANT AVANT D'OUVRIR UL WARNING: ELECTRICAL SHOCK HAZARD AVERTISSEMENT: RISQUE DE CHOC ELECTRIQUE WIRING INSTRUCTION Remarque: * Une résistance de fin de ligne répertoriée UL est disponible chez Apollo, réf. 44251-146 Note: ‘X’ denotes unused terminals. Remarque: "X" désigne les terminaux inutilisés.
PAGE 4
1. 2. a. b. 3. Class B | Fig. 4* Note:* A UL Listed End of Line resistor is required in Class B Remarque: * Une résistance de fin de ligne répertoriée UL est requise en classe B Continuité fonctionnelle de la terre. Ne vous connectez pas au backbox. Le blindage doit être scotché pour protéger du court-circuit au boîtier électrique Wiring diagram for shield when shielded cables are used | Fig.
PAGE 5
ADDRESS SETTING Steps: 1. The dip switch used to address your device has 10 individual switches. 2. Address setting is done by dip switches 1-8 (see page 7 for address matrix). a. In XP/Discovery Protocol, only dip switch 1-7 are used. b. Dip switch down = 1 and up = 0. 3. There is no Class A/B selection switch, the device determines wiring class by internal end of line resistor Remarque: * Une résistance de fin de ligne répertoriée UL est requise en classe B Fig.
PAGE 6
GROUP ADDRESS SETTING (XP MODE ONLY) In Group mode the NAC Module responds to an additional address referred to as the ‘group address’, which is used to activate groups of NAC Modules simultaneously (The module continues to respond to its own individual address and report its status from that address in the normal way). The group address is selected by the four-segment dip switch S2 which is factory-set to 0000.
PAGE 7
ADDRESS MATRIX Monitoring Enable Disable DC/AC 0: DC Monitoring 1: AC Monitoring 1 1000 0000 43 1101 0100 85 1010 1010 129 1000 0001 171 1101 0101 213 1010 1011 2 0100 0000 44 0011 0100 86 0110 1010 130 0100 0001 172 0011 0101 214 0110 1011 3 1100 0000 45 1011 0100 87 1110 1010 131 1100 0001 173 1011 0101 215 1110 1011 4 0010 0000 46 0111 0100 88 0001 1010 132 0010 0001 174 0111 0101 216 0001 1011 5 1010 0000 47 1111 0100 89 1001 1010 133 1010 0001
PAGE 8
APD0834 20 This page has been intentionally left blank indoor dry use only For NAC circuit, contact Panel manufacturer for compatibility details 1.175 5 Apollo America Inc. 30 Corporate Drive, Auburn Hills, MI 48326 Tel: (248) 332-3900. Fax: (248) 332-8807 Email: info.us@apollo-fire.com www.apollo-fire.com Surge Current 900 µA Max Standby Current (Pulsing LED) Max Alarm Current (Pulsing LED) Wire Range 3.1 mA © 2020 Apollo America Inc.