Quick Start Guide 24/32-CH DVR
24/32-CH DVR Quick Start Guide 1. Install Hard Drive &DVD Writer 1.1 Install Hard Drive Notice: 1. This series support eight(optional) or four SATA hard drives. Please use the hard drive the manufacturers recommend specially for security and safe field. Here take eight SATA hard drives installation for example. 2.Please calculate HDD capacity according to the recording setting. Please refer to “Appendix B Calculate Recording Capacity”.
24/32-CH DVR Quick Start Guide 1.2 Install DVD Writer Step 1: Unscrew and open the case and then unscrew the screws in the both sides to take out of the upper iron bar as shown below: Step 2: Install the DVD holder attached with the device. Please let the screw holes of the DVD aim at the holder‟s. Try to place the holder farther away from the front and then screw firmly. Then, unscrew and take the barrier out of the front panel.
24/32-CH DVR Quick Start Guide Fig 2-2 Rear Panel for 32-ch Item Name 1 Video out 2 Video in 3 Power input 4 Spot 5 6 7 8 Audio out MIC IN VGA port HDMI port 9 USB port 10 11 12 13 14 15 16 17 18 LAN E-SATA Alarm in Alarm out P/Z K/B Audio in Power switch Fan Description Connect to monitor Video input channels (from 1-24 for 24-ch DVR/ 1-32 for 32-ch DVR) AC 110Vor 110V Connect to monitor as an AUX output channel by channel.
24/32-CH DVR Quick Start Guide 3.2 Shutdown You can shut down the device by using IR remote controller and mouse. By IR remote controller: Step1: Press Power button. This will bring up a shutdown window. The unit will shut down by clicking “OK” button. Step2: Disconnect the power By mouse: Step1: Enter into Menu and select “Shut Down” icon. This will take you to a shutdown window. Step2: Click OK. Then the unit will power off after a while. Step3: Disconnect the power 4.
24/32-CH DVR Quick Start Guide The default HTTP port is 80. The default server port is 6036. You can check „Obtain an IP address automatically‟ to acquire network information or input IP address, subnet mask, gateway, preferred/alternate DNS server manually. This function is used to monitor DVR through internet (See Section 10 for details). Click „Next‟ button. This will take you to record setup window. Select resolution, fps, encode, quality and max bitrate.
24/32-CH DVR Quick Start Guide 6. Main menu setup Click right mouse, or press ENTER button on the front panel to enter into the main menu. Then click Setup to enter into Setup interface as shown in Fig 4-2. Basic configuration: Users can set video system, menu language, audio, time and authorization check. Live configuration：Users can set name/time display, picture color and hide cameras. Record configuration：Users can set record quality, frame rate, resolution, time stamp and recycle.
24/32-CH DVR Quick Start Guide A user needs to install and format a HDD, and set all the recording parameters before recording. There are four kinds of record modes. 7.1 Manual Recording A user can press REC button on the front panel after quitting system setup. Press this button again to stop recording. Or press REC button on remote controller. Click it again to stop. Or click REC button on the tool bar with mouse. Click it again to stop. 7.
24/32-CH DVR Quick Start Guide Step 1: Enter into MenuSetupScheduleMotion tab. The setup steps for schedule for motion based recording are similar to normal schedule setup. You can refer to 7.3 Schedule Recording for details. Step 2: Enter into MenuSetupAlarmMotionMotion tab as shown below. Step3: Enable motion alarm (Please specify to channel) and click „Apply‟ to save settings. Step4: Click „Setting‟ button under the Area to set Sensitivity and Detection area.
24/32-CH DVR Quick Start Guide Step 1: Enter into MenuSetupScheduleSensor tab. The setup steps for schedule for sensor based recording are similar to normal schedule setup. You can refer to 7.3 Schedule Recording for details. Step 2: Enter into MenuSetupAlarmSensorBasic tab as shown below. Step 3: Enable sensor alarm (Please specify to channel), select senor type and click „Apply‟ to save settings.
24/32-CH DVR Quick Start Guide 8.2 Playback by Time Search Step 1: Enter into MenuSearchTime Search tab. Step 2: Select date and channels on the right hand side and press “Search” button. A date with highlighted borderline indicates presence of data. Step 3: Set the start time by clicking a particular grid or by entering the specific value in the start time field. Step 4: Select the channel display mode and click Use the playback toolbar to control the playback. button to play record.
24/32-CH DVR Quick Start Guide 8.4 Playback by Image Search Step 1: Enter into MenuSearchImage tab. Step 2: Select data and channels on the right hand side. Step 3: Press “Search” button to search for a recorded image. Step 4: Once an alarm image has been identified, the user can double click the image to play the recording. You can lock the image by clicking “Lock” button. Click “Save” button to copy the image on the HDD. Click “Save All” to copy all images on the HDD.
24/32-CH DVR Quick Start Guide Step 3: Select a required file or checkmark “All” to select all data files. Click Backup button to pop up Backup information window. Step 4: In the backup information interface, user can check the relevant options for backing up files. These options include storage Media, backup player and save file type. Then click Start button to start backup. 10. Remote Surveillance In order to view the DVR from a network it must be connected to a LAN/WAN or internet.
24/32-CH DVR Quick Start Guide Input IP address, Subnet, Gateway. If using DHCP, please enable DHCP in both the DVR and the router. Forward IP address and port number in Virtual Server setup of the router or virtual server. Configure the firewall to allow accessing the DVR. (If the user has enabled the UPnP function in both the DVR and router, he can skip this step. Please refer to the relevant chapter for more details.) Open IE browser, input IP address, or dynamic domain name and enter.
