CPX1-241 Rugged Military Grade Rack Mount 24-Inch LCD Panel with MultiTouch IR Touch Screen Technical Reference Revision A 6/12/2013
This Page Intentionally Blank
Warranty The product is warranted against material and manufacturing defects for two years from date of delivery. Buyer agrees that if this product proves defective Chassis Plans’ is only obligated to repair, replace or refund the purchase price of this product at Chassis Plans’ discretion.
Trademarks Liability Disclaimer “The Original Industrial Computer Source”, “Systems Engineered to Perform” and Chassis Plans are registered trademarks of Chassis Plans, LLC. IBM, PC/AT, VGA, EGA, OS/2 and PS/2 are trademarks or registered trademarks of International Business Machines Corp. Intel is a registered trademark of Intel Corporation. MS-DOS and Microsoft are registered trademarks of Microsoft Corp.
Table of Contents Chapter 1 ‐ Introduction _______________________________________________________________ 1 Description _____________________________________________________________________________ 1 Genesis Based LCD Controller_______________________________________________________________ 2 Table 1 – Supported Video Resolutions ____________________________________________________________ 3 Rack Mounting __________________________________________________________________________ 3 Photos _________________
Chapter 3 – Power Supply Options ______________________________________________________ 15 AC Input Power Supply ___________________________________________________________________ 15 Table 5 ‐ AC Input Supply Specifications __________________________________________________________ 15 Photo 6 ‐ AC Power Supply (150W) ______________________________________________________________ 15 MIL‐STD‐704/1275 DC Input Converter ______________________________________________________ 16 Operating Specifications ______
Appendix D – Functional Description for De‐Interlacing Modes _______________________________ 53 Appendix E – PIP Mix Table ____________________________________________________________ 55 Table E‐1 – PIP Mix Table ______________________________________________________________________ 55 Appendix F – Ethernet Network Connection ______________________________________________ 57 Connecting a network port to CPX1‐241 _____________________________________________________ 57 Get the IP address using DHCP ________
This Page Intentionally Blank
Chassis Plans CPX1-241 Technical Reference Chapter 1 - Introduction Chapter 1 - Introduction Description The CPX1-241 is a rugged military grade and industrial grade high performance 9U mount-on-rack LCD panel display offering 24-inch TFT LCD display with LED backlight. The display includes a bonded anti-reflective glass cover with an optional bonded mesh EMI filter and an Infrared dual-touch touch screen.
Chassis Plans CPX1-241 Technical Reference Chapter 1 - Introduction Genesis Based LCD Controller The LCD Controller is a key component in any display system. This is a long life revision controlled military grade component. The controller board selected is based on the Genesis FLI30436 LCD Controller. It provides: Faroudja® signal processing including TrueLife™ Video Enhancer Next generation 10-bit Faroudja DCDi Cinema® format conversion Dual 10 bit video decoders for up to 1.
Chassis Plans CPX1-241 Technical Reference Chapter 1 - Introduction Supported Resolutions (continued) 1280 x 1024 @ 60 Hz 1280 x 1024 @ 60 Hz Digital Separate Sync Composite Sync 1280 x 1024 @ 60 Hz Sync on Green 1280 x 1024 @ 75 Hz 1280 x 1024 @ 75 Hz Digital Separate Sync Composite Sync 1280 x 1024 @ 75 Hz Sync on Green 1600 x 1200 @ 60 Hz 1600 x 1200 @ 60 Hz Digital Separate Sync Composite Sync 1600 x 1200 @ 60 Hz Sync on Green 1920 x 1080 @ 60 Hz 1920 x 1080 @ 60 Hz Digital Separate Syn
Chassis Plans CPX1-241 Technical Reference Chapter 1 - Introduction Photos Photo 1- Front View Photo 2- Rear View Photo 3-Bottom View Photo 4- Bottom Rear View Photo 5- Rear View Exploded Page 4
Chassis Plans CPX1-241 Technical Reference Chapter 1 - Introduction Photo 6- I/O Connections Page 5
Chassis Plans CPX1-241 Technical Reference Chapter 1 - Introduction Specifications ENCLOSURE INFRARED TOUCH SCREEN OPTION 9U (15.72”) x 3.
Chassis Plans CPX1-241 Technical Reference Chapter 1 - Introduction LCD DVI/HDMI/VGA Input Features: Controller Feature Summary Harsh Environment LCD Controller Inputs: Analog RGB: 75Hz at SXGA, WXGA, XGA, SVGA, VGA With auto detect of Digital Separate Sync, Sync-On-Green & Composite Sync. Auto detects VGA ~WUXGA interlaced & noninterlaced.
Chassis Plans CPX1-241 Technical Reference Chapter 1 - Introduction HD-SD/SDI Option The CPX1-241 can be optionally configured with a broadcast quality HD-SD/SDI input. Fully compliant with the SMPTE 259M-C, SMPTE 292M, SMPTE 424 and 425M standard. The option provides a re-clocked loop through output for “daisy chaining” multiple monitors or other equipment to the same HD-SDI source. HD-SD/SDI Specification: Interface Standards Supported Video Modes 576i50 (PAL) 480i60 (NTSC) 720p60 (4:2:2) 720p59.
Chassis Plans CPX1-241 Technical Reference Chapter 1 - Introduction Figure 1 – CPX1-241 Customer Drawing Page 9
Chassis Plans CPX1-241 Technical Reference Chapter 1 - Introduction Figure 2 – CPX1-241 Mounting Adapter Customer Drawing Page 10
Chassis Plans CPX1-241 Technical Reference Chapter 1 - Introduction LCD Enhancements In the CPX family of rugged military grade LCD displays, Chassis Plans starts with Grade A Industrial Quality LCD panels selected for optical performance, high reliability and long product life cycle.
Chassis Plans CPX1-241 Technical Reference Chapter 1 - Introduction fogging of the display. Finally, the added mass bonded to the front of the LCD display adds a thermal conduction path to help dissipate the heat generated in the backlights themselves. By eliminating the majority of reflected light, the apparent contrast improves making the display more legible in high bright situations.
Chassis Plans CPX1-241 Technical Reference Chapter 1 - Introduction DARO coatings offer superior optical performance by using multilayer anti-reflective coatings. The photopic brightness of the DARO coating is less than 0.5%, compared to the industry-standard bare glass at 4.25%. DARO coatings offer significant anti-reflection and clear viewing, especially in high-brightness environments. Figure 6 – Comparison with and without Optical Bonding Specifications Dry cheesecloth rub test with 1.5 lbs.
Chassis Plans CPX1-241 Technical Reference Chapter 2 – IR Touch Screen Option Chapter 2 – Infrared Touch Screen Option Description The IRTouch Systems Infrared Touch Screen is a thin bezel mounted between the rear of the front panel and the LCD display. It is mechanically mounted and sealed to maintain the IP65 rating of the front of the display. The touch screen provides 4096 x 4096 touch point resolution and any object greater than 8mm diameter including gloves can be used for touch activation.
Chassis Plans CPX1-241 Technical Reference Chapter 3 – Power Supply Options Chapter 3 – Power Supply Options AC Input Power Supply The AC Input Power Supply is a 150 W Medical Grade “Brick” style power supply. The output is provided with a circular mil connector for connecting to the LCD Display. The input accepts a standard IEC 320 plug. A bracket is provided to securely mount the supply in a rack. Alternate AC supplies are available as required by the application or environmental requirements.
Chassis Plans CPX1-241 Technical Reference Chapter 3 – Power Supply Options MIL-STD-704/1275 DC Input Converter The Mil-Std-704/1275 DC Input Converter provides true 704/1275 input specifications allowing reliable operation from nominal 28VDC input mains in a military environment. A Mil grade DC to DC Converter is provided in a rack mountable case with military grade circular connectors.
Chassis Plans CPX1-241 Technical Reference Chapter 4 – Ordering Information Chapter 4 – Ordering Information CPX1 = Panel Mount Extreme Monitor Options: 241A = 24” LCD with Bonded Glass with Oleophobic Anti Reflective Coating 241C = 24” LCD with IR Touch Screen, Bonded Glass with Oleophobic Anti Reflective Coating 241D = 24” LCD with IR Touch, Bonded Glass with Oleophobic Anti Reflective Coating and EMI filter mesh 241E = 24” LCD with Bonded Glass with Oleophobic Anti Reflective Coating and EMI filter mes
Chassis Plans CPX1-241 Technical Reference Chapter 4 – Ordering Information This Page Intentionally Blank Page 18
Chassis Plans CPX1-241 Technical Reference Chapter 5 – Package Contents Chapter 5 - Package Contents Part Description Quanty LCD Display Assembly Rack Mounting Adapter Bracket Power Supply Power Supply Rack Bracket 10-32 x 1” Pan Head Screws Plastic Rack Washers 10-32 Cage Nuts 10-32 Nuts Power Cord Kit – (Note 1) Manual Rack Ruler 1 1 1 1 12 12 12 12 1 1 1 Table 7 - Package Contents Notes: 1.
Chassis Plans CPX1-241 Technical Reference Chapter 5 – Package Contents This Page Intentionally Blank Page 20
Chassis Plans CPX1-241 Technical Reference Chapter 6 - Installation Chapter 6 - Installation Rack Installation To mount the CPX1-241 in a rack, it is first important you identify the correct holes to mount to. Please see the following illustration. Note that a ‘U’ starts between the holes that are ½” apart. One very common problem is trying to install into the wrong holes. Because there are multiple styles of racks, it is not possible to provide detailed instructions on mounting the equipment.
Chassis Plans CPX1-241 Technical Reference Chapter 6 - Installation Figure 10 – Installing the Mounting Adapter Bracket Install the Mounting Adapter Bracket to the rack using the appropriate screws for the rack. Note The Mounting Adapter Bracket is not symmetrical. The four holes in the middle (VESA pattern) should be below center. The monitor provides guide pins on both sides which slide into slots in the Mounting Adapter Bracket to help support the weight of the display and pre-align the screw holes.
Chassis Plans CPX1-241 Technical Reference Chapter 6 - Installation Connecting the Display The CPX1-241 provides for a single controller option with rear panel details provided below. Controller Rear Panel Connections The LCD controller used in the CPX1-241 provides a robust feature set. The board features full screen image expansion, on screen PIP, image marker and supports an optional 3G HD-SDI adaptor for professional and broadcast video applications. The controller supports 3x10-bit 1.
Chassis Plans CPX1-241 Technical Reference Chapter 6 - Installation Photo 8 –CPX1-241 Bottom View and I/O Table 7, following, details the connectors for the CPX1-241.
Chassis Plans CPX1-241 Technical Reference Chapter 7 – LCD Operation Chapter 7 – LCD Operation LCD Front Panel Controls The On Screen Display (OSD) is adjusted as follows: 1. Press the Menu Button located on the front of the monitor. 2. Use the buttons described below to maneuver around the Menu. 3. Select the desired OSD Menu from the Menu Screen Shots below to make the desired adjustment(s). 4.
Chassis Plans CPX1-241 Technical Reference Chapter 7 – LCD Operation LCD Controller OSD Menus OSD functions Picture : Volume ### Increase/decrease volume level, total: 100 steps Brightness Increase/decrease panel brightness level, total: 100 steps Contrast Increase/decrease panel contrast level, total: 100 steps Saturation Increase/decrease saturation, total: 100 steps Hue ** Increase/decrease Hue level, total: 100 steps Sharpness* Increase/decrease sharpness, total: 30 steps Backlight Backl
Chassis Plans CPX1-241 Technical Reference Chapter 7 – LCD Operation S-Video 2*** Component 1 Component 2*** PIP Port change + ++ PIP Off / Composite 1 / S-Video 1 / Component 1 / DVI / HDMI / HD/SD SDI 1 / HD/SD SDI ++ 2 ) PIP Size: Off / PIP Size/ 1~18 / Size by Size / Size by Size Tall The PIP capability on display input sources refer to Appendix E – PIP mix table PIP Position : Move the PIP position upward Move the PIP position downward Move the PIP position to the left Move the PIP position to th
Chassis Plans CPX1-241 Technical Reference Chapter 7 – LCD Operation setting “OFF”.
Chassis Plans CPX1-241 Technical Reference Chapter 7 – LCD Operation Use “-“ button to decrease the zoomed image Horizontal pan : : Pan the image horizontally Vertical pan : : Pan the image vertically Factory Reset Note : Freeze state will be cleared when you using zoom function.
Chassis Plans CPX1-241 Technical Reference Monochrome Mode - Chapter 7 – LCD Operation Color Red Monochrome Green Monochrome Blue Monochrome Red Only Green Only Blue Only Backlight Setup - B/L Invert : : Invert for the backlight brightness - B/L Control : D/A / PWM : Selection for voltage level dimming control / PWM dimming control - Backlight Frequency : - Light Detector : 100 ~ 440Hz in a step of 20 : Enable ambient light detector function by using KIT 70220-3 Default Setting Reset to Factory De
Chassis Plans CPX1-241 Technical Reference Appendix A – Display Serial Control Programming Appendix A – Display Serial Control Programming The LCD provides for remote serial RS232 or Ethernet control for the LCD through the rear panel Control Port as shown below.
Chassis Plans CPX1-241 Technical Reference Function Volume control left+right channel Volume control on/off (mute) Brightness control Contrast control all channels Saturation control Hue control Phase (tuning) control Image H position Image V position Sharpness Frequency Appendix A – Display Serial Control Programming Command 0x80, “a” | “A”, nn | “+” | “-” | “r” | “R” | “?” 0x80, “m” | “M”, “0” | “1” | “r” | “R” | “?” 0x81, nn | “+” | “-” | “r” | “R” | “?” “m” “n” “i” , ss, nn “o”, ss, Descript
Chassis Plans CPX1-241 Technical Reference Appendix A – Display Serial Control Programming Scaling Mode 0x8c, “0” | “1” | “2” | “3” | “9” | “A” | “B” | “C” | “D” | “r” | “R” | “?” Set graphic image scaling mode = value Reset Query OSD H position 0x90, nnn | “+” | “-” | “r” | “R” | “?” 0x91, nnn | “+” | “-” | “r” | “R” | “?” 0x92, n | “+” | “-” | “r” | “R” | “?” 0x93, nn | “+” | “-” | “r” | “R” | “?” Set osd_hpos = value/increment/decrement Reset Query Set osd_vpos = value/increment/decrement Reset Qu
Chassis Plans CPX1-241 Technical Reference Appendix A – Display Serial Control Programming Source Layout 0x9a, n| “r” | “R” | “?” Select source layout = Single, PIP, PBP, PBPT Reset, Query Video System (Composite, Svideo and Component Only) 0x9b, “0” | “1” | “2” | “3” | “r” | “R” | “S” | “s”| “?” Set video system = Auto/NTSC/PAL/SECAM Reset Video State Query Query GAMMA value select 0x9d, n | “r” | “R” “?” Select GAMMA value = Value Reset Query Auto power off 0x9f, “0” | “1” | “r” | “R” | “?” 0x
Chassis Plans CPX1-241 Technical Reference Appendix A – Display Serial Control Programming Hotkey 2 0xa0, “2”, n| “r” | “R” | “?” Set Hotkey 2 = value Reset Query Runtime counter 0xa1, nnnnn | “r” | “R” | “?” 0xa2, nn | “+” | “-” | “r” | “R” | “?” 0xa3, nn | “+” | “-” | “r” | “R” | “?” 0xa4, nnn | “+” | “-” | “r” | “R” | “?” 0xa5, nnn | “+” | “-” | “r” | “R” | “?” 0xa6, nn | “r” | “R” | “?” runtime counter value = nnnnn (* 0.
Chassis Plans CPX1-241 Technical Reference Zoom H position Appendix A – Display Serial Control Programming 0xa9, nnnn | “+” | “-” | “r” | “R” | “?” Set Zoom_hpos = value/increment/decrement Reset Query 0xaa, nnnn | “+” | “-” | “r” | “R” | “?” Set Zoom_vpos = value/increment/decrement Reset Query Horizontal Size 0xad, Vertical Size nnn | “+” | “-” | “r” | “R” | “?” 0xb0, Horizontal Pan nnn | “+” | “-” | “r” | “R” | “?” 0xb1, Set horizontal size for Aspect Size = value/increment/decrement Reset Qu
Chassis Plans CPX1-241 Technical Reference Red level for selected colour temperature Green level for selected colour temperature 0xb4, nn | “+” | “-” | “r” | “R” | “?” “m” “n” “i” , ss, c, nn “o”, ss, c 0xb5, nn | “+” | “-” | “r” | “R” | “?” “m” “n” “i” , ss, c, nn “o”, ss, c Blue level for selected colour temperature Graphic horizontal resolution enquiry Graphic vertical resolution enquiry Graphic horizontal sync frequency enquiry Graphic vertical sync frequency enquiry 0xb6, nn | “+” | “-” | “r” | “R
Chassis Plans CPX1-241 Technical Reference Set gamma data for user defined gamma curve 0xbf, mm, c, “?” Appendix A – Display Serial Control Programming Query External Memory 0xcb, “2” Query gamma data for color c index mm ( c = 0 for color Red, c=1 for color Green, c=2 for color Blue) Set user gamma curve to linear Set gamma data for color c index mm. (If c= 3, then gamma data for red, green & blue will be set at the same time.
Chassis Plans CPX1-241 Technical Reference Appendix A – Display Serial Control Programming Backlight PWM Frequency 0xe6, nnn | “+” | “-” | “R” | “r” | “?” Set Backlight PWM Frequency = value/increment/decrement Reset Query Backlight Invert 0xe7 “0” | “1” | “R” | “r” ”?” 0xe8, Set On or Off Red Offset for selected colour temperature Green Offset for selected colour temperature nn | “+” | “-” | “r” | “R” | “?” “m” “n” “i” , ss, c, nn “o”, ss, c 0xe9, nn | “+” | “-” | “r” | “R” | “?” “m” “n” “i” , ss
Chassis Plans CPX1-241 Technical Reference Appendix A – Display Serial Control Programming PIP Window Blend Level 0xed, nn | “+” | “-” | “R” | “r” | “?” Select PIP Transparency Level PIP Transparency value Reset Query PIP Window Auto Off “0xee”, “0x41” “0” |”1” “?” “0xee”, “0x42” “0” |”1” Auto Off / Auto On ScreenMarker CenterMarker “0xee”, “0x43” “0” |”1” Query Screen Marker Off / Screen Marker On AspectMarker “0xee”, “0x44” “0” |”1” Center Marker Off / Center Marker On Preliminary 4:3 /16:9
Chassis Plans CPX1-241 Technical Reference Appendix A – Display Serial Control Programming Display real time clock** “0xee”, “0x4D” “0” |”1” Real Time Clock Display Off / Real Time Clock Display “0”- Off “1”- On Custom Sizing 0xef, “0” | “1” | “2” ”?” Custom sizing selection : Overscan / Normal / Custom Query “0” – Overscan “1” – Custom / Underscan “2” – Normal Function Send Display Mark Command 0xF1, ”S” | ”0x21” | ”0x40” ”0x60” | ”0x7E” Return “1” Description Acknowledge (if enabled) “S” – Se
Chassis Plans CPX1-241 Technical Reference Appendix A – Display Serial Control Programming Function Select RS-232 acknowledge Command 0xc1, “0” | “1” | “2” | “3” Description Disable/enable command acknowledge. Auto-setup 0xc3 Command availability Auto-calibration 0xc4, n Freeze frame 0xc6, “0” | “1” Start auto-setup of current vmode. Check whether a command is available. Start auto-calibration of gain of the RGB amplifier.
Chassis Plans CPX1-241 Technical Reference Appendix A – Display Serial Control Programming Query BIOS version 0xcb, “0” Read BIOS version Query PCBA number Reset to Factory Defaults Reset to Factory Defaults with (color temp) Saved Calibrated default Load Calibrated default 0xcb, “1” Read PCBA number 0xce Reset all parameters to default value Reset all parameters for all video modes to default value Wide Screen Mode Selection 0xd9, “0” | “1”| “2” “r” | “R” “?” “0xee”, “0x42” “0” |”1” ScreenMarke
Chassis Plans CPX1-241 Technical Reference Appendix A – Display Serial Control Programming Text Via RS232 Command Function Send Line Command 0xF0, |”S” |”LL”|”TEXT”| “0x0A” Return “1” Description “S” = “0x53 or 0x73” Send command ------------------------------------------“LL” = “0x30,0x31~0x30,0x34” Line number (Rang 0~4 lines) ------------------------------------------“Text”= ASCII code, “0x20~0x7E” Character( Rang 0~34 ) ------------------------------------------0x0A = End of line Acknowledge (if ena
Chassis Plans CPX1-241 Technical Reference Left offset 0xF0, |”O” |”SSS”| Return “nnn” Appendix A – Display Serial Control Programming “O” = “0x4F or 0x6F” Set Left Offset command ------------------------------------------“SSS” = “0x30,0x30,0x30~ 0x33,0x46,0x46” Offset Value (Rang 000~3ff) “O” – Left Offset Command “SSS”- Offset Value (pixels) “nnn”- Return Value(pixels) e.
Chassis Plans CPX1-241 Technical Reference Appendix A – Display Serial Control Programming Display Mark Command Function Command Description Acknowledge (if enabled) Send Display Mark 0xF1, ”S” | ”0x21” | ”0x40” ”0x60” | ”0x7E” ”0x22” | ”0x42” # ”0x23” | ”0x43” # Return “1” “S” = “0x53 or 0x73” ASCII “0x21,0x40, 0x60,0x7E 0x22, 0x42” # 0x23, 0x43” # Return “ 0x31” “S” – Send Command 0x21 : Full size cell black block 0x40 : Full size cell white block 0x22 : 1/2 cell black block vertical size # 0x42
Chassis Plans CPX1-241 Technical Reference Bi-directional communication between Display Mark and IP50 # “0xee”, “0x64” “0x7B”| ”TEXT”| “0x7D” Return “1” Appendix A – Display Serial Control Programming Send command Start Text Command “TEXT” End of Text Command return to CN8 only “0xee 0x64” – Send Command “0x7B” – Start of Text “Text” – Character (ASCII fomat) “0x7D” – End of Text “1” - successful.
Chassis Plans CPX1-241 Technical Reference Appendix A – Display Serial Control Programming The RS-232 command strings sent in one time can support up to 380 bytes via CN8 port The RS-232 command string sent in one time can support up to 50 bytes via CN1 or J1 port. n = 1-byte ascii-coded hex number, e.g., parameter value of 0x1 is represented by “1” (0x31). mn or nn = 2-byte ascii-coded hex number, e.g., parameter value of 0x1e is represented by “1”, “e” | “E” (0x31, 0x6e|0x4e).
Chassis Plans CPX1-241 Technical Reference Appendix B – Auto Color Gain Appendix B – Auto Color Gain The Auto Color Gain function is supported in the ARGB mode only and is designed to calibrate the controller to the incoming video signal. In order to calibrate correctly, the display must be displaying an image containing both black and white data (see illustration below) when the function is used.
Chassis Plans CPX1-241 Technical Reference Appendix B – Auto Color Gain This Page Intentionally Blank Page 50
Chassis Plans CPX1-241 Technical Reference Appendix C – Remote Control Appendix C – Remote Control Chassis Plans offers an optional Remote Control for the CPX1-124 to allow direct control of the unit without having to access the front panel controls. The IR receiver is mounted on the front panel, lower right.
Chassis Plans CPX1-241 Technical Reference Appendix C – Remote Control BUTTON FUNCTION Soft power ON/OFF button. POWER BUTTON Use combined with digit keys to enable/disable the IR function.
Chassis Plans CPX1-241 Technical Reference Appendix E – PIP Mix Table Appendix D – Functional Description for De-Interlacing Modes In the OSD menu, see Utilities – Setup – De-Interlacing Mode AFM = Auto Film Mode : It is a frame based method which is used for the input ODD and EVEN fields have a fixed relation between each other, such as static image, 3:2 pull down mode. If two fields are correctly merged, it can display the best quality.
Chassis Plans CPX1-241 Technical Reference Appendix E – PIP Mix Table This Page Intentionally Blank Page 54
Chassis Plans CPX1-241 Technical Reference Appendix E – PIP Mix Table Appendix E – PIP Mix Table The CPX1-241 offers PIP (Picture In Picture) and PBP (Picture By Picture) modes. The following table shows which inputs can be combined in these modes.
Chassis Plans CPX1-241 Technical Reference Appendix E – PIP Mix Table This Page Intentionally Blank Page 56
Chassis Plans CPX1-241 Technical Reference Appendix F – Network Connection Appendix F – Ethernet Network Connection The CPX1-241 has an RJ-45 Ethernet port for control and monitoring over a network. This appendix introduces the two user interface modes: Command line direct mode (this is the default mode) Browser based web server mode There is also a short overview of the command set and how it is implemented in Appendix A.
Chassis Plans CPX1-241 Technical Reference Appendix F – Network Connection Get the IP address using DHCP When in a default state and powered on, the IP controller will first try to obtain its IP address and network information, such as Subnet Mask address, Gateway address, etc., from the DHCP server. The IP controller may also be configured manually. If you have a DHCP server on your network, the CPX1-241 automatically obtains its IP address from that server.
Chassis Plans CPX1-241 Technical Reference Appendix F – Network Connection Configure Firmware Version MAC Address Host Name DHCP IP Address Subnet Mask Default Gateway Primary DNS Address Firmware version of CPX1-241 MAC address of IP controller ID name without space (max.
Chassis Plans CPX1-241 Technical Reference Appendix F – Network Connection Step 1: Connect to the router and enter into its configuration page. Step 2: Locate the internal IP address of the CPX1-241. (e.g. 192.168.1.2) Image F-4 – IP Address Locator Step 3: Assign the internal IP of the CPX1-241 to DMZ function and enable it. Image F-5 – IP Address Setting and Enable In the above example, we can just type http://148.xxx.27.15 to enter web server of the CPX1-241.
Chassis Plans CPX1-241 Technical Reference Appendix F – Network Connection Step 2: Locate the internal IP addresses of all CPX1-241s. (e.g. 192.168.1.2 and 192.168.1.3) Image F-6 – DHCP Table Screenshot Step 3: Set all ports forwarding under NAT function of router. (see the screen below for example.) Image F-7 – NAT Fowarding Screenshot In the above example, we have to enter http://148.xxx.27.15:9080 to access CPX1-241-1 at 192.168.1.2 FTP://148.xxx.27.15:9021 to FTP CPX1-241-1 at 192.168.1.
Chassis Plans CPX1-241 Technical Reference Appendix F – Network Connection This Page Intentionally Blank Page 62
Chassis Plans CPX1-241 Technical Reference Appendix G – DVI-D versus DVI-I Appendix G – DVI-D versus DVI-I Connectors The Digital Visual Interface (DVI) is a video interface standard designed to provide very high visual quality on digital display devices such as flat panel LCD computer displays and digital projectors. It was developed by an industry consortium, the Digital Display Working Group (DDWG). It is designed for carrying uncompressed digital video data to a display.
Chassis Plans CPX1-241 Technical Reference Appendix G – DVI-D versus DVI-I This Page Intentionally Blank Page 64
