Mac Pro User’s Guide Includes setup, expansion, and troubleshooting information for your Mac Pro computer
Apple Inc. © 2007 Apple Inc. All rights reserved. This product includes software developed by the University of California, Berkeley, and its contributors. Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent of Apple. Intel, Intel Core, and Xeon are trademarks of Intel Corp. in the U.S. and other countries. The Apple logo is a trademark of Apple Inc., registered in the U.S. and other countries.
Contents 5 Chapter 1: Getting Started 5 Setting Up Your Mac Pro 13 Putting Your Mac Pro to Sleep or Shutting It Down 15 16 18 20 22 24 Chapter 2: Getting to Know Your Mac Pro Basic Features on the Front of Your Mac Pro Ports and Connectors on the Back of Your Mac Pro More Ports and Connectors on the Back Internal Expansion Options Getting Answers 27 28 32 38 47 50 Chapter 3: Working Inside Your Computer Opening the Computer Installing Memory Installing Internal Storage Devices Adding PCI Express Cards Re
56 Problems with Software 57 Keeping Your Software Up to Date 57 Problems with AirPort Wireless Communication 58 Problems with Your Display 60 Problems with Your Internet Connection 63 Using Apple Hardware Test 64 65 66 68 Reinstalling the Software That Came with Your Computer Maximizing Ethernet Performance Learning More, Service, and Support Locating Your Serial Number 69 Appendix A: Specifications 77 77 78 80 82 Appendix B: Safety, Maintenance, and Ergonomics Important Safety Information General Maint
1 Getting Started 1 Congratulations on purchasing your new high-performance Mac Pro computer. This chapter contains instructions for setting up your computer and display. Your Mac Pro features the latest computer technology, including advanced 64-bit multicore processor technology, high-speed FB-DIMM memory, PCI Express graphics and expansion cards, and internal storage, all in an anodized aluminum chassis with easy access to internal components.
Step 1: Position your computer and display Pick up your Mac Pro by both of its handles using correct lifting techniques. If your display is heavy, use correct lifting techniques when positioning it as well.
Step 2: Plug in the power cord Plug the power cord completely into the recessed power cord socket on the back of your Mac Pro and plug the other end into a grounded outlet or a grounded power strip.
Step 3: Connect the display Connect your display as shown in the illustration below. Depending on the display, you may have one or more cables to connect. Check the instructions that came with the display for additional setup information. Display ports USB port FireWire 400 port Display cable You can connect two displays with Digital Visual Interface (DVI) connectors to the display ports on the back of your Mac Pro. You can connect any Apple display to either port.
DVI display port DVI display ports DVI to VGA Display Adapter VGA connector on display cable You can also connect displays that have an Apple Display Connector (ADC) or a video graphics array (VGA) connector using one of the following adapters: Â To connect a VGA display, use the Apple DVI to VGA Display Adapter included with your Mac Pro to connect the display to the DVI port. Â To connect an ADC display, use an Apple DVI to ADC Display Adapter, not included, to connect the display to the DVI port.
Step 4: Connect an Ethernet cable To access the Internet or a network, connect one end of an Ethernet cable to either of the Ethernet ports on the back of your Mac Pro. Connect the other end to a DSL modem, cable modem, or Ethernet network. Gigabit Ethernet ports Step 5: Connect the keyboard and mouse Connect the keyboard cable to one of the USB (d) ports on the computer or on your display. Plug the Mighty Mouse cable into a USB port on the keyboard.
Plug the mouse into a USB port on the keyboard. Keyboard Mouse If the keyboard cable is not long enough to reach a USB port on your computer, use the keyboard extension cable that came with your computer.
Using a Wireless Keyboard and Mouse If you purchased an Apple Wireless Keyboard and Mouse with your Mac Pro, follow the instructions that came with the keyboard and mouse to set them up. Step 6: Turn on your Mac Pro Press the power (®) button on the front of the computer to turn it on. If your display must be turned on separately, turn it on by pressing its power button. Step 7: Use Setup Assistant The first time you turn on your Mac Pro, Setup Assistant starts.
 Are the keyboard and display cables connected correctly?  Is the display turned on? Are the brightness and contrast of the display adjusted correctly? If your display has brightness controls, adjust them.  If you still don’t see anything on your screen, restart your computer. Press and hold the computer’s power button for 5 or 6 seconds, until the computer turns off. Press it again to turn on the computer.
To wake your computer from sleep, do one of the following: Â Press any key on the keyboard. Â Click the mouse. Â Press the power button on the front of your Mac Pro. Shutting Down Your Mac Pro If you will not be using your Mac Pro for a day or more, you should turn it off. To turn off your Mac Pro, choose Apple () > Shut Down. WARNING: Do not turn off your Mac Pro by turning off the switch on a power strip or by pulling out the computer’s power plug (unless you can’t turn off the computer any other way).
2 Getting to Know Your Mac Pro 2 This chapter gives basic information you need to know about your Mac Pro. Read on for an overview of the features and ports of your computer. Getting the Latest Information The Apple website at www.apple.com links you to the latest Apple news, free downloads, and online catalogs of software and hardware for your Mac Pro. You can also find the manuals for many Apple products, and technical support for all of Apple’s products, on the Apple Support website at www.apple.
Basic Features on the Front of Your Mac Pro Optical drive 16 Status light Second optical drive (optional) f Headphone jack ® Power button USB 2.
Optical drive Your Mac Pro has a DVD+R DL/DVD±RW/CD-RW SuperDrive, which can read CD-ROM, photo CD, audio, and DVD discs. It can write music, documents, and other files to CD-R, CD-RW, DVD±R, DVD±RW, and DVD+R Double Layer (DL) discs. To open the drive, press the Media Eject (C) key on your Apple Keyboard. If your Mac Pro has a second optical drive, press the Option and Media Eject (C) keys to open it. ® Power button Press this button to turn on your Mac Pro, put it to sleep, or wake it from sleep.
Ports and Connectors on the Back of Your Mac Pro Power socket ¥ Locking latch d USB 2.
Power socket Connect the power cord that came with your Mac Pro. Do not use ordinary power or extension cords. ¥ Locking latch Lift the latch to open the side panel and access the internal components in your Mac Pro. If you are working inside your computer and the latch is down, the optical and hard drives are locked in place. You can attach a security lock to the latch to prevent access and secure the internal components.
More Ports and Connectors on the Back PCI Express expansion slots £ DVI display port 1 £ DVI display port 2 Optical digital audio out port Optical digital audio in port , Audio line-in port - Audio line-out port 20 Chapter 2 Getting to Know Your Mac Pro
PCI Express expansion slots (3) Expand your Mac Pro by installing up to three Peripheral Component Interconnect (PCI) Express cards in the covered slots labeled 2, 3, and 4. £ DVI display ports Connect displays that use a Digital Visual Interface (DVI) connector to the DVI display ports. Connect an Apple display, such as the 20-, 23-, or 30-inch Apple Cinema Display, to either port. For full resolution, connect the 30-inch Apple Cinema HD Display to port 1.
Internal Expansion Options Optical drive carrier Hard disk drive carriers (4) Slots 2–4: PCI Express Battery Slot 1: Double-wide PCI Express graphics (graphics card installed) Top memory card Bottom memory card 22 Chapter 2 Getting to Know Your Mac Pro
Optical drives Your Mac Pro comes with one or two DVD+R DL/DVD±RW/CD-RW SuperDrives in the optical drive carrier. To replace an optical drive, see “Replacing the Optical Drive” on page 42. Hard disk drive Your Mac Pro comes with up to four hard disk drives installed in the drive carriers. To install or replace the hard disk drives, see “Installing Internal Storage Devices” on page 38. PCI Express slots Your Mac Pro has three PCI Express expansion slots.
Getting Answers Much more information about using your Mac is available in Mac Help and on the Internet at www.apple.com/support. To open Mac Help: 1 Click the Finder icon in the Dock (the bar of icons along the edge of the screen). 2 Choose Help > Mac Help (click the Help menu in the menu bar and choose Mac Help). 3 Click in the search field, type a question, and press Return on your keyboard. More Information For more information about using your Mac Pro, see the following: 24 To learn about... See...
To learn about... See... Changing System Preferences Open System Preferences by choosing Apple () > System Preferences. Or open Mac Help and search for “system preferences.” Using your mouse or keyboard Open Mac Help and search for “mouse” or “keyboard.” Using AirPort wireless technology The AirPort Support page at www.apple.com/support/airport. Or open AirPort Help by clicking and holding the Home button at the top of a Mac Help page, and then choose AirPort Help from the list.
3 Working Inside Your Computer 3 Use the information in this chapter to customize and expand your Mac Pro to fit your needs. This chapter provides information and instructions for working inside your computer.
Opening the Computer 1 Before you open your Mac Pro, shut it down by choosing Apple () > Shut Down. · WARNING: Always shut down your Mac Pro before opening it to avoid damaging its internal components or the components you want to install. Do not open the computer or attempt to install items inside it while it is on. 2 Wait 5 to 10 minutes to allow the computer’s internal components to cool. · WARNING: Let your computer cool down before you touch the internal components, which may be very hot.
Touch the metal on top of the computer. 4 Unplug all the cables and the power cord from the computer. · WARNING: To avoid damaging internal components or the components you want to install, always unplug your Mac Pro. Don’t attempt to install items while it’s plugged in.
5 Hold the side panel and lift the latch on the back of the computer. Lift the latch while holding the side panel.
6 Remove the side panel. Pull the top of the side panel out and lift it up. Important: When you remove the side panel, hold it securely.
Installing Memory Your Mac Pro has two memory cards with 4 memory slots on each card (in four banks of two each). Your Mac Pro comes with a minimum of 1 GB of memory, installed as a pair of 512 MB fully buffered dual inline memory modules (FB-DIMMs) in two of the DIMM slots. You can install additional pairs of 512 MB, 1 GB, or 2 GB FB-DIMMS in the open DIMM slots on the memory cards.
To install memory: 1 Shut down your computer, open it, and remove the side panel, following the instructions on page 28. · WARNING: Let your computer cool down for 5 to 10 minutes before you touch the internal components. The components on the memory cards may be very hot. 2 Remove the memory card and place it on a soft, clean cloth.
3 Open the ejectors on the DIMM slot by pushing them out to the sides. 4 Align the first FB-DIMM in the slot on the memory card and push both ends of the FBDIMM down until the tabs are vertical and the ejectors snap into place. Repeat to install the second FB-DIMM. Don’t touch the gold DIMM connectors. Important: Add DIMMs to the memory cards in the order shown here.
With the computer on its side, push the memory cards straight down into the memory slots. 5 Lay your Mac Pro down on a soft, clean cloth on the desk or work surface to avoid scratching the work surface or your Mac Pro. 6 Install the memory cards, pushing slightly until they are seated in the memory slot.
7 Stand your Mac Pro up and replace the side panel. Important: When you replace the side panel, hold it securely so it stays in place as you push the latch down. Place the side panel in the slot and then push to close.
8 Push the latch down to secure the side panel. While pushing the side panel against the computer, push the latch down until it is firmly secured against the back of the computer. To lock the side panel or secure the computer, flip down the lock tab before you close the latch. This provides a metal loop through which you can attach a lock or cable.
Installing Internal Storage Devices Your Mac Pro has room for six internal drives: two optical drives and four hard disk drives. In most configurations, a single hard disk drive occupies the first hard drive bay and an optical drive is located in the top optical drive bay. You can add up to three additional Serial ATA (SATA) 3 Gbit/s hard disk drives to the empty hard drive bays. The drives must meet these specifications:  Type: SATA 3 Gbit/s  Width: 3.9 inches (102 mm)  Depth: 5.
To install a hard disk drive: 1 Open your Mac Pro and remove the side panel following the instructions that begin on page 28. 2 Lift the latch to unlock the hard drive carriers. Important: When the latch is down, the carriers are locked in the drive bays and can’t be removed. 3 Pull the hard drive carrier out of the drive bay. Pull out the hard drive carrier. Lift the latch to unlock the carriers.
4 Use the four screws on the carrier to attach the hard disk drive to the carrier. Important: If the printed circuit board is exposed on the bottom of the hard disk drive, hold the drive by its sides. To avoid damaging the drive, don’t touch the printed circuit board. Position the connectors towards the rear.
5 Lift the latch and then slide the carrier over the guides and into the drive bay, until it’s seated in the bay and snaps into place. The connectors on the drive plug into the computer when fully seated. Make sure the latch is up. 6 Replace the side panel and push the latch down to secure it.
Replacing the Optical Drive Your Mac Pro comes with one or two SuperDrives installed in the optical drive bays. Follow these instructions to replace your optical drive. Important: Contact your drive manufacturer or consult the manufacturer’s website to determine if your drive is set to cable select mode. Before installation, set the drive to cable select mode if the manufacturer hasn’t already done so.
4 Disconnect the power and ribbon cables from the optical drive and remove the carrier.
5 Remove the optical drive from the carrier by unscrewing the four attachment screws. 6 Use the four screws from the original optical drive to attach the replacement drive to the carrier.
7 Slide the optical drive and carrier over the guides halfway into the drive bay, 8 Attach the power and ribbon cables to the back of the drive.
9 Lift the latch and then slide the optical drive carrier into the drive bay, pushing it into place. Make sure the latch is up. 10 Replace the side panel and push the latch down to secure it.
Adding PCI Express Cards You can expand the capabilities of your Mac Pro by installing cards in the Peripheral Component Interconnect (PCI) Express slots. Your Mac Pro has one double-wide PCI Express graphics slot and three PCI Express expansion slots, for a total of four slots. These slots accommodate PCI Express graphics cards and expansion cards.
2 Lay your Mac Pro down on a soft, clean cloth to avoid scratching it or the work surface. 3 Unscrew the captive screws in the PCI bracket and remove the bracket. 4 Remove the port access cover from the slot in which you plan to install the card. PCI bracket Port access cover To remove a card, push on the tab to release the catch. 5 Remove your new card from its static-proof bag and hold it by its corners. Don’t touch the gold connector or the components on the card.
6 Align the card’s connector with the expansion slot and press the card into the slot. Did You Know?—Installing a Full-Length PCI Card It may be easier to install a PCI card if you remove the hard disk drives and carriers, and remove adjacent cards. If you have a full-length card, install the end of the card in the card guide first, and then align the card with the PCI slot to finish installing it. Secure the card with the PCI bracket. Insert the PCI bracket under the brace.
7 Press the card gently but firmly until the connector is fully inserted. Press only on the bare areas of the card to avoid damaging the components. Note: Don’t rock the card from side to side or force it. If you meet resistance, check the connector and slot for damage or obstructions, and then try inserting the card again. 8 Pull the card gently to see if it is properly connected. If it stays in place and its gold connectors are barely visible, the card is connected.
3 Remove the old battery from the holder. · WARNING: Installing the battery incorrectly may cause an explosion. Use only the same type of battery or an equivalent recommended by the manufacturer of the original. 4 Insert the new battery in the holder with the positive (+) side facing up. Slide the old battery out. Insert the new battery positive (+) side up. Remove the card in slot 1. Push on the tab to release the catch. 5 Replace the PCI Express cards that you removed (see page 47).
4 Troubleshooting 4 If you have a problem while working with your Mac Pro, here are some things you can try right away. Occasionally you may have a problem while working with your Mac Pro. This chapter gives you some solutions to try. Problems with Your Mac Pro If your Mac Pro won’t respond or turn on, you have trouble ejecting a disk, or the status light is flashing, try the steps in this section. The computer won’t respond or the pointer won’t move.
 Choose Apple () > Force Quit and select the application you want to quit. You can also force quit by pressing the Esc, Option, and Command (x) keys at the same time. Restart your Mac Pro by choosing Apple () > Restart to be sure the problem is entirely cleared up. You can also restart by pressing the power (®) button for about 5 or 6 seconds until your Mac Pro shuts down. Press the power (®) button again to start up your Mac Pro.
 If this doesn't work, restart your computer while holding down the Shift key. You are unable to eject a disc. A file on the disc may be in use. Quit applications that are open, and then try again. If that doesn’t work, choose Apple () > Restart and hold down either the mouse button or the Media Eject (C) key on your Apple Keyboard. If that doesn’t work: 1 Shut down the computer. 2 Gently press down the front panel covering the front of the drive tray.
Problems with Software When an application freezes or does not respond, Mac OS X provides a way to quit the application without restarting your computer. Quitting a frozen application may allow you to save your work in other open applications. To force an application to quit: 1 Press Command (x)-Option-Esc or choose Apple () > Force Quit from the menu bar. 2 Select the name of the application you want to quit in the Force Quit Applications dialogue. 3 Click Force Quit.
Keeping Your Software Up to Date You can connect to the Internet and automatically download and install the latest free software versions, drivers, and other enhancements from Apple. When you are connected to the Internet, Software Update checks Apple’s Internet servers to see if any updates are available for your computer. You can set your Mac to check the Apple servers periodically and download and install updated software. To check for updated software: 1 Open System Preferences.
 Check the AirPort signal level. You may have up to four bars in the AirPort status icon in the menu bar.  For more information, see the instructions that came with the wireless device or search for “AirPort” in Mac Help. Problems with Your Display WARNING: If you have a problem with your Apple display and nothing in this manual solves it, contact an Apple Authorized Service Provider or Apple for assistance.
 Reset the PRAM by restarting the computer while holding down the Command (x), Option, P, and R keys until you hear the startup sound a second time. Then start up using the software installation disc that came with your computer. The screen image appears dim or flickers.  Adjust the display brightness and contrast settings. Some displays have brightness and contrast controls on or under their front edge. Or you may be able to adjust brightness or contrast using the Displays pane of System Preferences.
The screen freezes. Â Force the frozen application to quit. Choose Apple () > Force Quit and select the application. Â If that doesn’t work, force the computer to restart by pressing the power button (®) for 5 or 6 seconds until your Mac Pro shuts down. Press the power button (®) again to start up your Mac Pro. The light on the front of the display is flashing. On some Apple flat panel displays, the power light displays a series of short flashes when an error is detected.
3 Click Diagnostics to open Network Diagnostics. 4 Follow the onscreen instructions. If Network Diagnostics can’t resolve the problem, there may be a problem with the Internet service provider (ISP) you are trying to connect to, with an external device you are using to connect to your ISP, or with the server you are trying to access. You can also try the steps in the following section.
6 Click PPPoE. 7 Select “Connect using PPPoE.” 8 Check the Account Name field to be sure you have entered the correct information from your ISP. 9 Retype your password if you chose to save your password, making sure it is correct. 10 Click TCP/IP. Make sure you’ve entered the correct information from your ISP in this pane. 11 Click Apply Now. Network Connections Make sure the Ethernet cable is plugged into your computer and into the network.
Using Apple Hardware Test You can use Apple Hardware Test to help determine if there is a problem with your computer’s hardware. To use Apple Hardware Test: 1 Disconnect all external devices from your computer except the keyboard and mouse. If you have an Ethernet cable connected, disconnect it. 2 Insert the Mac OS X Install Disc 1 that came with your computer. 3 Restart your computer and hold down the D key as it starts up. A list of available startup volumes appears.
Reinstalling the Software That Came with Your Computer Use the software installation discs that came with your computer to reinstall Mac OS X and the applications that came with your computer. Important: Apple recommends that you back up the data on your hard disk before restoring software. Apple is not responsible for any lost data. Installing Mac OS X To install Mac OS X: 1 Back up your important files, if possible. 2 Insert the Mac OS X Install Disc 1 that came with your computer.
3 Double-click “Bundled Software.” 4 Follow the onscreen instructions. 5 Select the destination disk for installation and continue following the onscreen instructions. Note: iCal, iChat, iSync, iTunes, and Safari are part of Mac OS X. To install these applications, follow the “Installing Mac OS X” instructions above. Maximizing Ethernet Performance Your computer performs best when the Ethernet port to which it is connected is set to autonegotiate. Ask your network administrator to verify this setting.
Learning More, Service, and Support If your Mac Pro needs service, take it to an Apple Authorized Service Provider or contact Apple for service. You can find more information about your Mac Pro through online resources, onscreen help, System Profiler, or Apple Hardware Test. If you didn’t order AirPort or Bluetooth wireless technology with your Mac Pro, contact an Apple Authorized Service Provider or an Apple Store. Online Resources For online service and support information, go to www.apple.com/support.
AppleCare Service and Support Information Your Mac Pro comes with 90 days of telephone support and one year of service coverage at an Apple-authorized repair center. You can extend your coverage by purchasing the AppleCare Protection Plan. For more information, visit the website address for your country listed below. If you need further assistance, AppleCare telephone support representatives can help you with installing and opening applications, and with basic troubleshooting.
Locating Your Serial Number System Profiler shows the serial number of your Mac Pro. Open System Profiler, located in the Utilities folder in the Applications folder, and click the System Profile tab. The serial number is also on the configuration label, which is located on the back of your Mac Pro near the video ports.
Specifications A Appendix A Processor and Memory Specifications Processor  Two dual-core or two quad-core Intel Xeon processors  4 megabytes (MB) of on-chip L2 cache per dual-core processor  8 MB of on-chip L2 cache per quad-core processor  1333 MHz dual independent frontside buses Random-access memory (RAM)  Fully buffered Dual Inline Memory Modules (FB-DIMMs)  PC2-5300, 667 MHz FB-DIMMs  DIMMs must be installed in pairs of equal size and equal specification (an equal number of devices per DIMM)
 Nonparity System Profiler, located in the Utilities folder in the Applications folder, provides information about your computer, including the amount of memory. Graphics Card PCI Express graphics card with two Digital Visual Interface (DVI) connectors. Video Display Modes For technical specifications for your display:  Apple displays: Go to www.apple.com/displays.  Non-Apple displays: Go to www.apple.com/guide.
 Video CD  Enhanced CD  DVD-Video  DVD±R  DVD±RW  DVD+R DL USB Specifications  Support for Universal Serial Bus (USB) 2.0 and 1.1  Seven external USB Type A ports  Two USB 2.0 ports on the front  Three USB 2.0 ports on the back  Two USB 1.1 ports on the Apple Keyboard  Each rear port is on a separate 480 megabit-per-second (Mbit/s) USB channel  500 milliamperes (mA) available for a total of 1.5 A on the rear and 1.
Power  Output voltage: Approximately 12 V  Output power: Up to a maximum of 28 W for all 4 ports or 7 W for any one port Ethernet Specifications  IEEE 802.
AirPort Extreme Specifications (Optional)  Frequency band: 2.4 and 5 gigahertz (GHz)  Radio output power: 20 dBm (nominal) Compatibility  802.11a, b, g, and draft n Optical Digital Audio Specifications  Data format: Sony/Phillips Digital Interface (S/PDIF) protocol (IEC60958-3)  Connector type: TOSLINK optical (IEC60874-17)  Bits per sample: 16-bit or 24-bit Optical digital audio out Based on a typical situation with playback of 1 kHz, 0dBFS 24-bit sine wave, 44.
Analog Audio Specifications  Sample rate: 44.1 kHz, 48 kHz, or 96 kHz  Jack type: 1/8” mini  Bits per sample: 16-bit or 24-bit  Frequency response: 20 Hz to 20 kHz, +0.5 dB/-3 dB Analog audio out using the headphone jack (typical values) Based on a typical situation with playback of 1 kHz, -3dBFS 24-bit sine wave, 44.1 kHz output sample rate into 150 ohms unless otherwise specified below.  Output voltage: 1.4 volts (root mean square) (Vrms) (+5.
Analog audio line out (typical values) Based on a typical situation with playback of 1 kHz, -3dBFS 24-bit sine wave, 44.1 kHz output sample rate into 100 kilohms unless otherwise specified below.  Output voltage: 1.6 Vrms (+6.3 dBµ)  Output impedance: 24 ohms  Signal-to-noise ratio: Greater than 90 dB  Total harmonic distortion + noise: Less than -85 dB (.
System Clock and Battery Your computer has CMOS custom circuitry with a long-life battery. Battery Use a 3-volt, CR 2032 Lithium coin cell replacement battery (see “Replacing the Internal Backup Battery” on page 50). Dimensions and Operating Environment Dimensions  Weight: 19.2 kg (42.4 lbs.) Weight depends on configuration. The weight above is for a basic configuration and may be greater if optional devices are installed.  Height: 511 mm (20.12 in.)  Width: 206 mm (8.11 in.)  Depth: 475 mm (18.70 in.
Safety, Maintenance, and Ergonomics B Appendix B This appendix provides important information about safety procedures, routine maintenance, and ergonomic considerations for using your computer and display. Important Safety Information The only way to disconnect power completely from your computer is to unplug the power cord from the main power supply. To disconnect your display completely, you must also unplug its power cable from the computer or power outlet.
 Your computer or display has been dropped or the case has been otherwise damaged  You suspect that your computer or display needs service or repair  You want to clean the computer or the case or screen of the display  If you plan to store your computer for an extended period of time, remove the battery. For service or questions about your warranty, contact an Apple Authorized Service Provider or Apple. Service and support information is included with your computer's documentation.
4 Clean the display screen with soft, lint-free paper or cloth dampened with mild soap and water. · WARNING: Do not spray liquid directly onto the display screen. Liquid could drip inside the display and cause electrical shock. 5 Wipe the computer or display case surfaces lightly with a clean, soft cloth dampened with water. Important: Don’t use alcohol, aerosol sprays, solvents, or abrasives that might damage the finish on the case.
 Do not write on the screen or touch the screen with a sharp object.  If you will not be using your display and computer for a day or more, turn off the computer and display or use Energy Saver.  Turn off your display, turn down the brightness, or use a screen saver program that dims or varies the image on the screen when the computer is idle for a prolonged time.
 Position the mouse at the same height as your keyboard. Allow adequate space to use the mouse comfortably.  Arrange the display so that the top of the screen is slightly below eye level when you’re sitting at the keyboard. The best distance from your eyes to the screen is up to you, although most people seem to prefer 18 to 28 inches (45 to 70 cm).  Position the display to minimize glare and reflections on the screen from overhead lights and nearby windows. If possible, use a tiltable display stand.
For more information about health, safety, and maintenance, go to the Apple ergonomic website at www.apple.com/about/ergonomics. Avoid Hearing Damage WARNING: Permanent hearing loss may occur if earbuds or headphones are used at high volume. You can adapt over time to a higher volume of sound that may sound normal but can be damaging to your hearing. If you experience ringing in your ears or muffled speech, then stop listening and have your hearing checked.
Regulatory Compliance Information Compliance Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. See instructions if interference to radio or television reception is suspected.
Responsible party (contact for FCC matters only): Apple Inc., Product Compliance 1 Infinite Loop M/S 26-A Cupertino, CA 95014-2084 Wireless Radio Use This device is restricted to indoor use due to its operation in the 5.15 to 5.25 GHz frequency range to reduce the potential for harmful interference to cochannel Mobile Satellite systems. Cet appareil doit être utilisé à l’intérieur.
Korea Mouse Statement Taiwan Wireless Statements Taiwan Statement Korea Keyboard Statement Taiwan Class B Statement VCCI Class B Statement Korea Statements Singapore Wireless Certification Mouse Class 1 LED Information The Apple Mighty Mouse is a Class 1 LED product in accordance with IEC 60825-1 A1 A2. It also complies with the Canadian ICES-003 Class B Specification.
External USB Modem Information When connecting your Mac Pro to the phone line using an external USB modem, refer to the telecommunications agency information in the documentation that came with your modem. Apple and the Environment Apple Inc. recognizes its responsibility to minimize the environmental impacts of its operations and products. More information is available on the web at: www.apple.
Taiwan: European Union—Disposal Information The symbol above means that according to local laws and regulations your product should be disposed of separately from household waste. When this product reaches its end of life, take it to a collection point designated by local authorities. Some collection points accept products for free.
Index Index A Bluetooth 72 E adapter 9 DVI to ADC 9 DVI to VGA 9 AirPort 73 Analog 21 analog audio 74 line in 21, 74 line out 21, 74 AppleCare Service and Support 67 Apple Hardware Test 66 applications force quit 54 freezing 56 installing 64 problems 56 assistants Setup Assistant 12 C ergonomic information 80 Ethernet 19, 72 maximizing performance 65 Expansion Slot Utility 47 B battery disposal 86 internal backup battery 23 replacing 50 CD-RW 70 changing the desktop 12 System Preferences 12 computer
PCI Express cards 47 SuperDrive 42 Internet problems connecting 61 P N PCI Express expansion slots 21, 23 graphics card 23 installing cards 47 PCI slots 21, 23 Ports headphone 17 ports 75 audio 21 display 8, 21 Ethernet 10, 19 FireWire 17, 19, 71 power 72 USB 10, 17, 19, 71 power button 12, 17 power cord 7 power socket 19 problems connecting to Internet 61 processor 69 protective film 5 network connections 62 no image on screen 58 R J JEDEC specification 69 K keyboard extender cable 11 L latch 19 M