K Service Source Macintosh
K Service Source Basics Macintosh
Basics Overview - 1 Overview This manual includes repair procedures for the earliest Apple Macintosh computers—the Macintosh 128K and Macintosh 512K.
K Service Source Specifications Macintosh
Specifications Processor - 1 Processor CPU Motorola 68000 microprocessor 7.
Specifications Memory - 2 Memory RAM ROM PRAM 128K or 512K 64K CMOS custom chip with 4.
Specifications Disk Storage - 3 Disk Storage Floppy Drive Internal, single-sided drive; uses 3.5-in.
Specifications I/O Interfaces - 4 I/O Interfaces Floppy Drive External drive port; DB-19 connector Mouse Mouse port; DE-9 connector Keyboard Synchronous serial keyboard bus; RJ-11 connector Serial Two RS-232/RS-422 serial ports; DE-9 connectors
Specifications I/O Devices - 5 I/O Devices Keyboard 58 keys; software mapped; RJ-11 connector Mouse Mechanical tracking; optical shaft encoding at 3.54 pulses per mm (90 pulses per in.
Specifications Sound and Video - 6 Sound and Video Sound Generator Four-voice sound with 8-bit digital/analog conversion, using 22-kHz sampling rate Video Display 9-in.
Specifications Electrical - 7 Electrical Line Voltage 105–125 VAC Frequency 50–60 Hz Maximum Power 60 W
Specifications Physical - 8 Physical Dimensions Weight Height: 13.6-in. (34.5 cm) Width: 9.6-in. (24.4 cm) Depth: 10.9-in. (27.6 cm) 16 lb. 8 oz. (7.
K Service Source Troubleshooting Macintosh
Troubleshooting General/ - 1 General The Symptom Charts included in this chapter will help you diagnose specific symptoms related to your product. Because cures are listed on the charts in the order of most likely solution, try the first cure first. Verify whether or not the product continues to exhibit the symptom. If the symptom persists, try the next cure. (Note: If you have replaced a module, reinstall the original module before you proceed to the next cure.
Troubleshooting Symptom Charts/Video - 2 Symptom Charts Video No video, but audio tone is present and drive operates 1 2 3 4 5 Turn contrast control fully clockwise. Check video cable connections. Replace power supply board. Replace neck cable. Replace logic board. Retain customer’s SIMMs. Screen is bright and audio is present, but no video information is present 1 2 Replace power supply board. Replace logic board. Retain customer’s SIMMs.
Troubleshooting Symptom Charts/Drives - 3 Drives Disk ejects; display shows disk icon with blinking “X” 1 2 3 4 Replace Replace Replace Replace Unable to insert disk all the way 1 Insert opened paper clip into small hole beside drive slot, or switch off system power and hold mouse ∑∑button down while switching system power back on to complete eject cycle. Then insert disk with metal slot forward and writeprotect tab on bottom. Replace floppy drive. 2 bad disk. floppy drive cable. drive.
Troubleshooting Symptom Charts/Drives (Continued) - 4 Drives (Continued) Drive does not eject disk Insert opened paper clip into small hole beside drive slot, or switch off system power and hold mouse button down while switching system power back on to complete eject cycle. Does not read disks on internal drive 1 2 3 4 5 6 Replace bad disk. Replace floppy drive cable. Replace Mylar RFI shield. Replace floppy drive. Verify ROMs on the logic board (refer to Additional Procedures). Replace logic board.
Troubleshooting Symptom Charts/Peripherals - 5 Peripherals Cursor does not move 1 2 3 Connect mouse. Replace mouse. Replace logic board. Retain customer’s SIMMs. Cursor moves, but clicking mouse produces no response 1 2 Replace mouse. Replace logic board. Retain customer’s SIMMs. No response to any key on keyboard 1 2 3 Replace keyboard cable. Replace keyboard. Replace logic board. Retain customer’s SIMMs. No response from a particular key 1 2 3 Replace keyswitch. Replace keyboard.
Troubleshooting Symptom Charts/Peripherals (Continued) - 6 Peripherals (Continued) Known-good ImageWriter or ImageWriter II does not print 1 2 Known-good LaserWriter does not print 1 2 3 4 5 3 Make sure that Chooser and Control Panel are set correctly Check that system software version is compatible. Replace software with known-good version. Reset PRAM. Replace interface cable. Replace logic board. Retain customer’s SIMMs. Make sure that Chooser and Control Panel are set correctly.
Troubleshooting Symptom Charts/Miscellaneous - 7 Miscellaneous When turned on, the Macintosh continuously beeps and tries to power up 1 2 Clicking or chirping sound 1 2 3 4 3 4 Perform voltage adjustment. Refer to Adjustments chapter. Disconnect internal disk drive. If this eliminate problem, replace drive. Replace logic board. Retain customer’s SIMMs. Caution: Replacing only power supply board may damage new power supply board.
Troubleshooting Symptom Charts/Miscellaneous (Continued) - 8 Miscellaneous (Continued) Smoke/odor issues from the Macintosh Caution: Replacing only power supply board may damage new power supply board. Replace power supply board, logic board, and internal drive, then turn on Macintosh. No video, no audio tone, and no drive operation 1 2 3 4 5 6 Connect power cord. Turn on power. Replace power cord. Check fuse. Caution: Replacing only power supply board may damage new power supply board.
Troubleshooting Symptom Charts/Miscellaneous (Continued) - 9 Miscellaneous (Continued) When developer’s switch is installed, Macintosh sometimes resets intermittently Remove switch and file it down about 1/16 inch. Macintosh 512K enhanced has two RFI shields Some machines have two RFI shrouds installed. Two RFI shields can be replaced by one RFI shield, which can be ordered as a service part.
K Service Source Take Apart Macintosh
Take Apart Cover - 1 Cover No preliminary steps are required before you begin this procedure. Warning: This product contains high voltage and a high-vacuum picture tube. To prevent serious injury or equipment damage, review CRT safety and discharge instructions in Bulletins/Safety.
Take Apart Cover - 2 1 Cover 2 Battery Compartment Cover Reset/Interrupt Switch Remove the battery compartment cover. Remove the reset/ interrupt switch, if present.
Take Apart Cover - 3 3 4 Using a Torx screwdriver, remove the four case screws. Using the pull-apart tool, gently pry off the cover. ±Warning: The edges of the metal chassis may be sharp. When moving the computer with the cover off, be sure to handle the chassis carefully.
Take Apart Cover - 4 5 RFI Shield Remove the RFI shield.
Take Apart Ground Lug Anode Cap Power/Sweep Board - 5 Power/Sweep Board Power/Sweep Board Before you begin, • Remove the cover • Discharge the CRT • Remove the anode cap This product contains high voltage and a high-vacuum picture tube. To prevent serious personal injury or equipment damage, review CRT safety and discharge instructions Bulletins/Safety.
Take Apart Power/Sweep Board - 6 Yoke Cable Logic Board Cable Neck Cable Never use a grounding wriststrap until after discharging the CRT. ±Warning: 1 2 Screw and Lockwasher Disconnect the following cable connectors from the power/sweep board: • Yoke cable • Logic board cable • Neck cable Remove the screw and lockwasher that hold the ground wire to the chassis.
Take Apart Power/Sweep Board - 7 3 Note: You may need to remove the insulating paper from the power/ sweep board to access the mounting screws. Remove the three mounting screws and washers, and lift the power/sweep board from the chassis. Replacement Note: After replacing all parts except the cover, perform the voltage and video adjustment procedures. See “Voltage” and “Video” in the Adjustments chapter.
Take Apart Power/Sweep Board - 8 Replacement Note: When sending a defective power/ sweep board to Apple, be sure to include the cable that connects to the logic board. Be sure the contrast control knob and battery have been removed from the defective board and reinstalled onto the exchange board.
Take Apart Logic Board - 9 Logic Board Before you begin, • Remove the cover • Discharge the CRT Warning: This product contains high voltage and a high-vacuum picture tube. To prevent serious personal injury or equipment damage, review CRT safety and discharge instructions in Bulletins/Safety.
Take Apart Logic Board - 10 Never use a grounding wriststrap until after discharging the CRT.
Take Apart Logic Board - 11 2 Caution: When removing the logic board, be careful not to damage the SIMMs — especially the larger DIP SIMMs that may be installed on the board. Pull back on the top of the logic board, and carefully slide out the logic board. Replacement Note: After replacing all parts except the cover, perform the voltage and video adjustment procedures. See “Voltage” in Adjustments.
Take Apart Logic Board - 12 Replacement Note: When exchanging the 512K logic board, you must swap ROMs to the new logic board. Replacement Note: Remove the SIMMs from the defective logic board and install them on the replacement logic board. See Hardware/Memory.
Take Apart CRT - 13 CRT CRT Before you begin, • Remove the cover • Discharge the CRT • Remove the Power/ Sweep board Warning: This product contains high voltage and a high-vacuum picture tube. To prevent serious personal injury, review CRT safety and discharge instructions in Bulletins/Safety.
Take Apart CRT - 14 Never use a grounding wriststrap until after discharging the CRT. ±Warning: Handle the CRT by its sides only. Do not grasp the neck on the CRT or touch the anode. ±Warning: Ground Wire 1 2 Slide the CRT socket cable straight off the neck of the CRT. Remove the four mounting screws and the ground wire, and lift the CRT off the bezel.
Take Apart CRT - 15 If you must dispose of the CRT, refer to “CRT Disposal” in Bulletins/Safety. ±Warning: Replacement Note: If you replace the CRT, perform the video and yoke adjustment procedures. See “Video” and “Yoke” in the Adjustments chapter.
Take Apart Floppy Drive - 16 Floppy Drive Before you begin, • Remove the cover • Discharge the CRT • Remove the logic board Floppy Drive This product contains high voltage and a high-vacuum picture tube. To prevent serious personal injury or equipment damage, review CRT safety and discharge instructions in Bulletins/Safety.
Take Apart Floppy Drive - 17 Floppy Drive Never use a grounding wriststrap until after discharging the CRT. ±Warning: Remove the four mounting screws, and slide the floppy drive out of the chassis.
Take Apart Floppy Drive - 18 Replacement Note: All 400K drives are shipped in their original drive shields. When installing a new 800K drive, remove the shipping fixture, plastic dust shield (if any), and packing disk from the new drive. Install the new drive in the customer’s original drive shield. Note: Before you install a replacement drive, remove the dust shield, if there is one.
Take Apart Chassis - 19 Chassis Before you begin, • Remove the cover • Discharge the CRT • Remove the logic board • Remove the Power/ Sweep board • Remove the floppy drive Warning: This product contains high voltage and a high-vacuum picture tube. To prevent serious personal injury or equipment damage, review CRT safety and discharge instructions in Bulletins/Safety.
Take Apart Chassis - 20 Never use a grounding wriststrap until after discharging the CRT. ±Warning: Remove the five mounting screws and lift the chassis off the bezel.
K Service Source Upgrades Macintosh
Upgrades Floppy Drive Upgrade Kit - 1 Floppy Drive Upgrade Kit Floppy Drive Before you begin, • Remove the cover • Discharge the CRT • Remove the logic board This product contains high voltage and a high-vacuum picture tube. To prevent serious personal injury or equipment damage, review CRT safety and discharge instructions in Bulletins/Safety.
Upgrades Floppy Drive Upgrade Kit - 2 Never use a grounding wriststrap until after discharging the CRT. ±Warning: D5 D8 Note: This kit replaces the 400K floppy drive on a 512K Macintosh with an 800K floppy drive. The kit contains the new drive and two new ROMs for the logic board. The new ROMs support both the 400K and the 800K drives. This upgrade is not recommended for the 128K Macintosh.
Upgrades Floppy Drive Upgrade Kit - 3 1 2 D5 D8 Using an IC extractor, remove the old ROMs from locations D5 and D8. Install the two new ROMs as follows: • ROM HI at location D5 • ROM LOW at location D8 Note: Be sure that the notched ends of the ROMs face the front of the computer.
Upgrades Floppy Drive Upgrade Kit - 4 3 Remove the floppy drive. Refer to “Floppy Drive” in the Take Apart chapter.
Upgrades Floppy Drive Upgrade Kit - 5 4 Reinstall the logic board. See “Logic Board” in the Take Apart chapter.
Upgrades Floppy Drive Upgrade Kit - 6 5 6 Install the new 800K floppy drive. See “Floppy Drive” in the Take Apart chapter. Return the old ROMs and the 400K drive to Apple (refer to the instructions in the kit).
Upgrades Logic Board Upgrade Kit - 7 Logic Board Upgrade Kit Before you begin, • Remove the cover • Discharge the CRT • Remove the logic board This product contains high voltage and a high-vacuum picture tube. To prevent serious personal injury or equipment damage, review CRT safety and discharge instructions in Bulletins/Safety.
Upgrades Logic Board Upgrade Kit - 8 Never use a grounding wriststrap until after discharging the CRT. ±Warning: D5 D8 Note: This kit cannot be installed unless the Floppy Drive Upgrade Kit has been installed. The Logic Board Upgrade Kit upgrades the logic board of a 512K Mac to a Mac Plus. The kit contains a new logic board with 1 MB of RAM, an RFI shield, and a new rear cover.
Upgrades Logic Board Upgrade Kit - 9 1 2 D5 D8 Using an IC extractor, remove the ROMs from locations D5 and D8 on the 512K logic board. Install the two ROMs in the new logic board: • ROM HI at location D5 • ROM LOW at location D8 Note: Be sure that the notched ends of the ROMs face the front of the computer.
Upgrades Logic Board Upgrade Kit - 10 3 Install the new logic board in the computer. See “Logic Board” in the Take Apart chapter.
Upgrades Logic Board Upgrade Kit - 11 4 5 6 Install the new RFI shield. Install the new cover. See “Cover” in the Take Apart chapter. Return the old logic board, old RFI shield, and old cover to Apple.
Upgrades 400K Drive ROM Upgrade - 12 400K Drive ROM Upgrade Before you begin, • Remove the cover • Discharge the CRT • Remove the logic board This product contains high voltage and a high-vacuum picture tube. To prevent serious personal injury or equipment damage, review CRT safety and discharge instructions in Bulletins/Safety.
Upgrades 400K Drive ROM Upgrade - 13 Never use a grounding wriststrap until after discharging the CRT. ±Warning: D5 D8 Note: Current 400K drives contain a new stepper motor that requires the replacement of the two boot ROMs on the Macintosh 128K and 512K. The new ROMs are compatible with new and old stepper motors. 1 Using an IC extractor, remove the ROMs at locations D5 and D8.
Upgrades 400K Drive ROM Upgrade - 14 2 D5 D8 Install the two new ROMs on the logic board: • ROM HI at location D5 • ROM LOW at location D8 Note: Be sure that the notched ends of the ROMs face the front of the computer.
Upgrades 400K Drive ROM Upgrade - 15 3 Reinstall the logic board in the computer. See “Logic Board” in the Take Apart chapter.
K Service Source Adjustments Macintosh
Adjustments Voltage - 1 Voltage Before you begin, remove the cover. This product contains high voltage and a high-vacuum picture tube. To prevent serious personal injury or equipment damage, review CRT safety and discharge instructions in Bulletins/Safety.
Adjustments Voltage - 2 Power/Sweep Board Caution: Because you must make voltage adjustments from the rear of the computer, use a mirror to view the computer screen. Do not reach around the computer to adjust the controls. Note: You must verify voltages after you replace the logic board or the power/sweep board.
Adjustments Voltage - 3 1 2 Set the voltmeter to 20 V scale. Connect the Macintosh voltage test cable (Apple part number 0770135) to the external drive port. Caution: Shorting the test cable plugs to each other can damage the Macintosh computer. Pull the rubber hoods over the plugs.
Adjustments Voltage - 4 4 Voltage Regulator Power/Sweep Board 5 6 7 8 ground terminal and the computer chassis. Connect the orange test cable lead to the voltage input terminal on the voltmeter. Switch on the computer. Adjust the voltage regulator on the power/ sweep board to between 11.90 V and 12.75 V. Switch off the power. Disconnect the orange test lead and pull the insulated hood over the plug.
Adjustments Voltage - 5 9 Connect the red test cable lead to the voltage input terminal on the voltmeter. 10 Switch on the computer. Voltage Regulator Power/Sweep Board 11 Adjust the voltage regulator on the power/ sweep board to between 4.85 V and 5.15 V.
Adjustments Voltage - 6 12 Switch off the power. 13 Disconnect the red test lead 14 and pull the insulated hood over the plug. Voltage Regulator Power/Sweep Board 15 Repeat the tests to verify that both voltages are within the specified tolerances. Note: If the power/sweep board will not adjust so that both voltages fall within tolerance, replace the board.
Adjustments Yoke - 7 Yoke Before you begin, • Remove the cover • Discharge the CRT Warning: This product contains high voltage and a high-vacuum picture tube. To prevent serious personal injury or equipment damage, review CRT safety and discharge instructions in Bulletins/Safety.
Adjustments Yoke - 8 Caution: Because you must make yoke adjustments from the rear of the computer, use a mirror to view the computer screen. Do not reach around the computer to adjust the controls. Note: If you replace the CRT, you may need to adjust the yoke.
Adjustments Tilt Adjustment - 9 Tilt Adjustment Note: If glue holds the yoke collar in place, use an art knife to cut through the glue. Yoke Collar Yoke Clamp Screw 1 2 Loosen the yoke clamp screw two or three turns. Switch on the computer.
Adjustments Tilt Adjustment - 10 3 Yoke Collar With one hand, grasp the plastic spokes of the yoke collar and rotate the yoke collar until the top and bottom edges of the picture are parallel with the top and bottom of the bezel.
Adjustments Tilt Adjustment - 11 4 5 6 Yoke Collar Yoke Clamp Screw Switch off and unplug the computer. Discharge the CRT. Caution: Do not overtighten the yoke clamp screw. Hold the plastic collar in position and slowly tighten the yoke clamp screw so that the collar cannot slip.
Adjustments Tilt Adjustment - 12 7 8 Replace the cover and switch on the computer. Make sure the top and bottom edges of the picture are parallel with the top and bottom of the bezel.
Adjustments Tilt Adjustment - 13 Centering Ring Adjustment 1 2 Turn off the computer and remove the cover. Turn on the computer Note: If glue holds the yoke collar in place, use an art knife to cut through the glue. 3 Centering Rings To center the picture, hold the front centering ring steady and move the rear ring. Then hold the rear centering ring steady and move the front ring.
Adjustments Video - 14 Power/Sweep Board Video Before you begin, remove cover. This product contains high voltage and a high-vacuum picture tube. To prevent serious personal injury, review CRT safety and discharge instructions in Bulletins/Safety. ±Warning: Note: You must perform the video adjustments whenever the CRT or the power/sweep board is replaced. Switch on the computer.
Adjustments Video - 15 Contrast and Brightness 1 Brightness Control External Contrast Control 2 3 4 Turn the external contrast control fully clockwise. Turn the brightness control fully counterclockwise so that white lines are visible. Turn the brightness control clockwise until the white lines just disappear. Turn the external contrast control 1/8 of a turn counterclockwise.
Adjustments Video - 16 Size Adjustment 1 Width Control Height Control 2 Using an alignment tool, adjust the width control until the raster is 7 inches (177.8 mm) wide. Using an alignment tool, adjust the height control until the raster is 4.7 inches (119.4 mm) high.
Adjustments Video - 17 Focus Adjustment 1 2 Focus Control Turn the focus control clockwise to its limit. Turn the focus control counterclockwise 1/8 of a turn.
K Service Source Exploded View Macintosh
Exploded View 1 Exploded View CRT and Yoke Assembly 076-0103 Front Bezel 810-0373 Internal Drive Shield 805-0765 (400K) 805-0217 (800K) CRT Socket Cable 590-0160 Floppy Drive 661-7615 (400K) 661-0345 (800K) Internal Drive Cable 590-0167 (red) 590-0437 (yellow) Insulator Shield 725-0011 Power/Sweep Board 661-76214 Chassis 805-0766 462-3100 426-1001 Logic Board 661-06236 Rear Housing 630-5139 426-1007 435-5002 RFI Shroud 805-0577
