Macintosh User’s Guide Includes setup, troubleshooting, and important health-related information for your Macintosh computer
K Apple Computer, Inc. © 1994 Apple Computer, Inc. All rights reserved. Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent of Apple. Your rights to the software are governed by the accompanying software license agreement. The Apple logo is a trademark of Apple Computer, Inc., registered in the U.S. and other countries.
Contents Communications regulation information 1 Getting Started 1 Plugging in the computer 1 Installing an expansion card Connecting a monitor 3 3 Connecting the mouse and keyboard Connecting other equipment Turning the computer on 6 7 8 Problems turning your computer on? What’s next? 10 11 Learning the basics Reviewing the basics 12 13 Turning the computer off Where to find answers 2 Getting Help vi 14 15 17 Getting answers to your questions Identifying objects on the screen Learning
3 Connecting Additional Equipment 29 Where to connect additional equipment 30 Connecting an Apple PlainTalk Microphone Connecting external stereo speakers Expanding memory 31 32 34 Installing internal drives 34 4 Installing and Using Application Programs Installing application programs 36 Working with several programs at a time Backing up your files 5 Troubleshooting 38 39 When you have questions 39 When you run into trouble 39 Solutions to common problems Initializing a hard disk 43 5
Appendix A Health, Safety, and Maintenance Tips 75 Health-related information about computer use Safety instructions 80 Handling your computer equipment Cleaning your equipment Opening the computer 81 85 Appendix B Installing an Expansion Card 87 89 Installing a processor-direct slot (PDS) card Installing a communication card Closing the computer 92 93 95 Appendix C Special Keys on Your Keyboard Index 75 99 101 Contents v
Communications regulation information FCC statement This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with the specifications in Part 15 of FCC rules. See instructions if interference to radio or television reception is suspected. Radio and television interference The equipment described in this manual generates, uses, and can radiate radio-frequency energy.
DOC statement DOC Class B Compliance This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of the Department of Communications.
Macintosh computer Monitor Keyboard cable (sometimes built into the keyboard as shown here) Keyboard Mouse Monitor cable (sometimes built into the monitor) Monitor power cord (sometimes built into the monitor) Computer power cord
Follow the instructions in this chapter to set up your computer and learn the basics. 1 Getting Started The illustration on the facing page shows all the equipment you will need to set up your computer and begin using it. Place your equipment on a sturdy, flat surface near a grounded wall outlet.
When you are ready to begin, follow these steps: 1 Plug the socket end of the computer’s power cord into the recessed power cord socket (marked with the symbol ≤) on the back of the computer. 2 Plug the other end of the power cord into a three-hole grounded outlet or power strip. Choose a power outlet to which you have easy access. WARNING This equipment is intended to be electrically grounded.Your Macintosh is equipped with a three-wire grounding plug—a plug that has a third (grounding) pin.
Installing an expansion card If you purchased any expansion cards for your Macintosh, install them now. (For instructions, see Appendix B, “Installing an Expansion Card,” as well as the documentation that came with the cards.) If you don’t have an expansion card, go on to the next section, “Connecting a Monitor.” Connecting a monitor You can connect many types of monitors to your Macintosh. To connect a monitor from a manufacturer other than Apple, refer to the instructions that came with the monitor.
2 Connect the monitor power cord to the monitor. On some monitors, the cord is already attached. 3 Plug in the monitor power cord. Be sure to plug the power cord into a three-hole grounded outlet or power strip.
Connecting the monitor cable After you plug in the monitor power cord, you connect the monitor cable to the computer’s monitor port. To connect the monitor cable, follow these steps: 1 Attach the monitor cable to the monitor. On some monitors, the cable is already attached (as shown below). 2 Attach the monitor cable to the monitor port on the back panel of the computer. The monitor port is marked with the ™ icon (symbol).
Connecting the mouse and keyboard You have a choice of several keyboards for your Macintosh. The way you connect the mouse and keyboard depends on whether the keyboard has a separate cable or a built-in cable. Connecting a keyboard with a separate cable 1 Plug the mouse cable into the port on either side of the keyboard. Most right-handed people prefer to use the mouse with their right hand; most left-handed people prefer to use their left hand. Plug the mouse into the port on the side you prefer.
Connecting a keyboard with a built-in cable 1 Plug the mouse cable into the recessed port on the back of the keyboard. The plug and the port are marked with the ◊ icon (symbol). The positions of the port and icon on your keyboard may be different from those pictured. By the way: A port marked with the ◊ icon is called an Apple Desktop Bus (ADB) port. Plug the mouse into the recessed port on the keyboard. The flat part of the plug should be pointing down, as shown here.
Turning the computer on Follow these steps to turn the computer on: 1 Turn on the monitor. See the information that came with your monitor for the location of the power button. 2 Turn on your computer by pressing the Power key. The Power key is at the top of the keyboard. You can recognize this key by the triangle outline on it (P). You hear a tone from the computer as it starts up.
3 Check to see what’s on your screen. m If you see the Macintosh desktop, as in the illustration below, your system software has already been installed, and your computer is ready to use. Skip now to the section “What’s Next?” later in this chapter. Hard disk icon Macintosh desktop m If you see a blinking question mark, you need to install system software on your computer’s hard disk. (System software is the set of programs your computer uses to start itself up.
Problems turning your computer on? If you don’t see anything on the screen, check these items to see if you can identify the problem: m Is the computer plugged into a power source? If it is plugged into a power strip, is the power strip turned on? m Is the computer turned on? The power-on light on the front panel should be on. If it isn’t on, press the standby power button on the computer’s back panel (marked with the symbol I).
What’s next? Congratulations! You’ve finished setting up your computer. Now continue with one of the following steps: m If you are new to the Macintosh, turn to the next section, “Learning the Basics.” m If you are an experienced Macintosh user, turn to Chapter 2, “Getting Help,” to learn about Macintosh Guide, your main source of information when you’re working with the Macintosh. m If you want to connect other equipment, such as a printer, to your computer, see Chapter 3, “Connecting Additional Equipment.
Learning the basics If you are new to the Macintosh, you should begin by looking at the easy-touse program called the Macintosh Tutorial. The tutorial teaches you the basic skills you’ll need to use your computer. To start the tutorial, follow these steps: 1 Slide your mouse along your mouse pad or desk. Hold the mouse as shown, with the cable pointing away from you. Don’t press the mouse button (under your index finger).
4 While holding down the mouse button, move the arrow until the words “Macintosh Tutorial” are highlighted, then release the mouse button. A window appears welcoming you to the tutorial. You can set this book aside for now and follow the instructions on the screen. When you have completed the tutorial, return to this book. Reviewing the basics The following illustration summarizes many of the basic skills and terms you learned from the tutorial.
Turning the computer off To turn the computer off, you choose Shut Down from the Special menu. Detailed instructions follow. 1 Move the tip of the arrow to the word “Special” at the top center of the screen. If the word “Special” does not appear at the top of the screen, you’re working in the wrong program. Pull down the Application menu (to the right of the Guide [h] menu) and choose Finder. Then try step 1 again. 2 With the tip of the arrow on the word “Special,” press and hold down the mouse button.
Where to find answers When you have questions about using your Macintosh, there are several places you can look for answers. In this book Macintosh User’s Guid e Use this book to help you set up your computer and learn about it, or to find solutions to problems. In the Guide menu The Guide menu (marked with the h icon) is your main source of information about the Macintosh. To learn how to get different kinds of help from the Guide menu, see Chapter 2 in this book.
Use the instructions in this chapter to learn about the help available to you in the Guide menu. 2 Getting Help The Guide menu is your main source of information when you’re working with your computer. The menu is identified by a question mark (h) in the upper-right corner of the screen.
Getting answers to your questions When you have a question while working with your computer, you can get the answer by choosing Macintosh Guide from the Guide menu. 1 Pull down the Application menu (in the upper-right corner of the screen) and choose Finder to make it the active application program. A checkmark in the menu indicates that the Finder is the active program. 2 Pull down the Guide menu (marked with the h icon) and choose Macintosh Guide. The Macintosh Guide window appears.
3 Notice the three buttons at the top of the window: Topics, Index, and Look For. Macintosh Guide gives you three ways of finding information: m Topics lets you choose from a list of general subjects; it is like the table of contents in a book. m Index lets you choose from an alphabetical list of more specific subjects; it is like the index in a book. m Look For lets you search for information related to a specific word or phrase that you type.
2 Click “Setting Options” in the list of topics. When you click any topic area, a list of related questions appears on the right side of the Macintosh Guide window. To get instructions, click a question… …and then click OK. 3 Click the question “How do I set the time and date?” and then click OK. Or double-click the question. A small window appears with instructions for you to follow. If you want to return to the main Macintosh Guide window, click here.
Getting answers with the Index button 1 In the Macintosh Guide window, click the Index button. An alphabetical list of subjects appears on the left side of the window. Slider Scroll bar 2 Scroll through the alphabetical list until the phrase “background pattern” is visible. You can scroll through the list either by dragging the slider to the letter B or by using the scroll bar at the right of the list. 3 Click the phrase “background pattern” in the alphabetical list.
4 Click the question “How do I change the background pattern?” and then click OK. Or double-click the question. A small window appears with instructions for you to follow. If you want to return to the main Macintosh Guide window, click here. 5 Click here to see the next step (if there is one). Read and follow the instructions in the window. Macintosh Guide provides step-by-step instructions to answer the question you selected.
Getting answers with the Look For button 1 In the Macintosh Guide window, click the Look For button. A small box appears on the left side of the window, where you can type text. To activate the text box, click here. Type a word or phrase in the text box… …and then click here. 2 Click the arrow button to activate the text box. 3 Type “sound” in the text box and then click Search.
4 Click the question “How do I change the beep sound?” and then click OK. Or doubleclick the question. A small window appears with instructions for you to follow. If you want to close Macintosh Guide, click here. Click here to see the next step (if there is one). 5 Read and follow the instructions in the window. Macintosh Guide provides step-by-step instructions to answer the question you selected.
Tips for using Macintosh Guide Here are a few tips for using Macintosh Guide effectively: m Macintosh Guide is available only when you are in the Finder—the desktop area where you can see the icons of disks, folders, and files. (Other programs may also have help available in the Guide menu, however.) If you don’t see Macintosh Guide in the Guide menu, pull down the Application menu (to the right of the Guide menu) and choose Finder.
Identifying objects on the screen Sometimes you’ll see an unfamiliar item on the screen and ask yourself, “What’s that?” You can get an answer by using a Macintosh feature known as Balloon Help. Balloon Help explains the function of icons, menus, commands, and other items on the Macintosh screen in balloons like those you see in comic strips. Follow these steps to use Balloon Help: 1 Pull down the Guide menu (marked with the h icon) and choose Show Balloons.
Learning useful shortcuts You can perform many tasks in the Finder more quickly if you use keyboard or mouse shortcuts. For example, instead of clicking an icon and choosing Open from the File menu, you can simply double-click the icon to open it. Follow these steps to learn keyboard and mouse shortcuts: 1 Pull down the Guide menu (marked with the h icon) and choose Shortcuts. The main Macintosh Shortcuts window appears.
2 Click one of the category buttons. Another window appears, describing shortcuts for that category. If you want to close the window, click here. Click here to return to the main Macintosh Shortcuts window for more categories. 3 Click here to see the next window (if there is one). Read about the shortcuts available for the category you selected. Click the right arrow in the lower-right corner of the window to display the next window (if there is one).
Read this chapter for information on expanding your computer system with additional hardware. 3 Connecting Additional Equipment The illustration below shows a basic Macintosh system. You can expand your computer system by connecting additional hardware (such as a printer, modem, or external audio speakers). Monitor Floppy disk drive Computer Remote control sensor CD-ROM drive (optional) Volume buttons Use these buttons to change the volume of the computer’s sound.
Where to connect additional equipment The illustration on this page shows where equipment should be connected to your computer. For instructions on connecting additional equipment such as a printer or scanner, see the manual that came with the equipment. Video input card access cover Covers port for optional video input card. TV tuner access cover Covers port for optional TV tuner card.
Connecting an Apple PlainTalk Microphone Your computer has a sound input port, which you can use to connect an Apple PlainTalk Microphone. Use PlainTalk only: You should connect only the Apple PlainTalk Microphone. Other models of microphone will not work with your Macintosh. To connect the microphone, do this: m Plug the microphone’s connector into the sound input port (marked with the icon X) on the back of the computer.
Connecting external stereo speakers You can take advantage of your computer’s stereo sound output by attaching external powered (amplified) speakers. 1 Assemble the speakers and the cable you need. You need a cable with stereo miniplugs at each end to connect one or both speakers to the computer. (Some speakers require a dual-plug adapter. Others, like those shown here, accept a single stereo miniplug and are joined by standard speaker wires.
5 Connect the speakers together with speaker wires, if necessary. 6 Turn on the computer. You hear the computer’s sound through the external speakers. Note: To control the volume of your external speakers, use the volume button on the front of the computer. If you are playing an audio compact disc (CD), you may also need to adjust the volume control in the program you’re using to play CDs.
Expanding memory The random-access memory (RAM) in your computer can be expanded. Installing additional RAM adds more memory chips to your computer and expands its capabilities. The Technical Information booklet that came with your computer describes how much additional memory can be installed in your Macintosh. Memory for your computer is provided in packages called Single Inline Memory Modules (SIMMs).
Read this chapter for information on installing and using application programs with your computer. 4 Installing and Using Application Programs Your computer has several application programs already installed, as well as some programs that must installed before you can use them. You will need to run the application program’s Installer program before the application programs will work. You’ll find these programs on your hard disk.
Installing application programs You’ll probably want to buy and install additional application programs. See the manuals you receive with your programs for instructions on installing and using them. In most cases, you’ll install an application program on your internal hard disk from floppy disks that contain the program. The following illustration shows how to insert a floppy disk in your computer’s floppy disk drive. Insert the floppy disk, metal end first, into the floppy disk drive of your computer.
Working with several programs at a time You can open as many application programs and desk accessories as your computer’s memory allows. All open programs are listed in the Application menu at the right end of the menu bar. The name of the active program (the one you’re using right now) has a checkmark next to it, and its icon appears in the menu bar. The Finder icon Commands to hide or display open windows A checkmark indicates the active program.
Hiding and showing windows on the desktop You can hide all windows except those of the active program by choosing Hide Others from the Application menu. The other programs remain open even though their windows are hidden. When you switch to another program, its windows become visible again. If you want to see all the open windows, choose Show All from the Application menu. Backing up your files Making backup copies of important files is good protection against possible damage to the originals.
Consult this chapter if you experience problems using your computer. 5 Troubleshooting When you have questions If you want to know how to do a particular task with your computer, refer to Macintosh Guide in the Guide (h) menu. For instructions on using Macintosh Guide, see Chapter 2 of this manual. When you run into trouble While you’re using your computer, you may occasionally see a bomb icon or an error message, or you may have a problem such as the pointer (8) “freezing” on the screen.
Take your time When you see an error message, you don’t have to take action immediately. The message stays on the screen until you click the OK button or turn off the Macintosh. To help diagnose and correct the problem, gather as much information on the situation as you can before starting over. m Make a note of exactly what you were doing when the problem occurred. Write down the message on the screen and its ID number (if any).
Start over Often you can eliminate a problem simply by clearing the computer’s memory and starting over. If you can, save any open documents before restarting the Macintosh. If your system is frozen and does not respond to anything you do, or if you have a “bomb” message on the screen, saving may not be possible. You can try pressing x-Option-Esc to quit the program in use when the problem occurred; if this works, you can then save the documents open in other programs before restarting.
Rebuild your desktop regularly A process known as “rebuilding the desktop” helps your Macintosh keep track of data on your startup disks. Although you usually use the hard disk in your computer as a startup disk, you can also start up from any other disk that has system software installed. It’s a good idea to rebuild the desktop of your startup disks once a month or so. To rebuild the desktop of a startup disk, follow these steps: 1 Hold down the Option and x keys while you start up your computer.
Solutions to common problems The computer is turned on but the screen is dark. One of the following is probably the cause: m You have a screen saver program that darkens the screen when the computer has not been used for a certain period. Press a key or move the mouse to turn off the screen saver. m The monitor’s brightness control (¤) is not adjusted properly. Check the monitor’s brightness control and turn it up if necessary. m The Macintosh or the monitor is not getting power.
When you start up, a disk icon with a blinking question mark appears in the middle of the screen. This icon indicates that your Macintosh cannot find the system software it needs to start up. One of the following is probably the cause: m Your computer may be having a problem recognizing external equipment that uses the Small Computer System Interface (SCSI). Turn off all external SCSI equipment and disconnect the first SCSI device in the chain from your computer’s SCSI port. Then restart the computer.
When you try to start up from a floppy disk, a disk icon with an X appears in the middle of the screen and the floppy disk is ejected. This icon indicates that the floppy disk you tried to start up from is not a startup disk. Wait a few seconds. The computer should start up from its internal hard disk. Make sure you insert floppy disks only after the computer has begun starting up. A “sad Macintosh” icon appears and the computer won’t start up.
m Check the ID numbers of all SCSI equipment connected to your computer. See the manuals that came with your SCSI equipment for information on setting SCSI ID numbers. m If the hard disk is your startup disk, start your computer using the Disk Tools floppy disk or (if you have a built-in CD-ROM drive) with the CD-ROM disc that contains system software.
If you are trying to use a DOS disk, consider the following: m The disk may have been formatted incorrectly on a DOS computer. On DOS computers it’s possible to format a standard double-sided disk in a high-density (1440K) format, and vice versa. Disks formatted in this way cannot be read by a Macintosh computer. When formatting disks on a DOS computer, always format standard double-sided disks in the 720K format. Always format high-density disks in the 1440K format.
A dialog box with a bomb appears. Your system has a software problem. m Write down what you were doing when the message appeared, the text of the message, and the message number, if there is one. m Restart your Macintosh. (See “Start Over” in the section “When You Run Into Trouble” earlier in this chapter for instructions.) Most software problems are temporary, and restarting usually corrects the problem. m Check the startup disk and application program you were using when the dialog box appeared.
Check the startup disk and program you were using when the problem occurred. Make sure that all programs, desk accessories, and system extensions you’re using are compatible with the system software. Try starting up the computer from the Disk Tools disk or the CD-ROM disc that contains system software. (For instructions on how to start up your computer from the CD-ROM disc, see “Starting Up From a CD-ROM Disc” in the section “Initializing a Hard Disk” later in this chapter.
If the problem recurs, you may need to reinstall system software. See “Installing or Reinstalling System Software” later in this chapter for instructions. m You haven’t selected any text or set the insertion point (9). Make sure the program you want to type in is the active program. Then place the pointer (8) in the active window and click to set an insertion point (9) or drag to select text (if you want to replace the text with your typing). m The keyboard is not connected properly.
You can’t start an application program or it quits unexpectedly. Or, when you try to open a program, you see a message that not enough memory is available. One of the following is probably the cause: m The Macintosh ran out of memory. Quit the programs that you have open and then open the program you want to use, or restart your Macintosh. Use the Memory control panel to turn on virtual memory.
You see a message that an application program can’t be found. The following dialog box appears if you try to open a document that was created with software that is not on your hard disk. Normally, you see this message if you try to open a document that came from another Macintosh with software that is different from yours. m Some documents can be opened by more than one application program.
You experience problems using a document from a DOS computer. If you can’t open a DOS document using a Macintosh program, try the following: m Open the document from within the program by choosing Open in the program’s File menu. m Use the PC Exchange control panel to change the document’s type to one that can be opened by the program.
Initializing a hard disk Before you can use a new disk, the disk must be prepared so that the computer knows where to store information on the disk. This preparation is called initializing (or formatting) the disk. When do you need to initialize a hard disk? The hard disk inside your computer was initialized at the factory, so you shouldn’t need to initialize it.
If a blinking question mark appears, or if the computer starts up from your hard disk: You did not insert the CD-ROM disc quickly enough for the computer to recognize it as a startup disk. Follow these steps: 1 Shut down your computer. The CD-ROM disc will remain in the CD-ROM drive. 2 Turn the computer on. 3 Immediately press the C key on the keyboard. Continue to hold down the key until you see the “Welcome to Macintosh” message.
Reinitializing your computer’s internal hard disk You initialize your internal hard disk using a program called Internal HD Format, which is on the floppy disk labeled Disk Tools that came with your computer. If your computer came with a CD-ROM drive and you didn’t receive floppy disks, you can find Internal HD Format on the CD-ROM disc that contains system software. 1 Start up your computer from the Disk Tools disk or the CD-ROM disc that contains system software.
Initializing an external SCSI hard disk You initialize an Apple external SCSI hard disk using a program called Apple HD SC Setup, which is on the floppy disk labeled Disk Tools that came with your computer. If your computer came with a CD-ROM drive and you didn’t receive floppy disks, you can find Apple HD SC Setup on the CD-ROM disc that contains system software. 1 Start up your computer from the Disk Tools disk or the CD-ROM disc that contains system software.
5 Click Init to initialize the hard disk. Click here to initialize the disk. 6 If a message appears asking you to name the disk, type a name and then click OK. 7 Click Quit when you see a message reporting that initialization was successful. If a message reports that initialization failed, try again. If initialization fails a second time, take the disk to your Apple-authorized service provider for repair.
Repairing a damaged disk Disks can become damaged by repeated use and handling. When do you need to repair a disk? If you see a message reporting that a disk is damaged or unreadable, you may need to repair the disk. Try these suggestions first If you can’t start up from a hard disk or you don’t see the hard disk icon on the desktop, try the following: m If the hard disk is internal, shut down your Macintosh, wait at least 10 seconds, and then turn it on again.
Checking for damage on your internal hard disk You can check for damage on your internal hard disk with the Internal HD Format program, which is on the floppy disk labeled Disk Tools that came with your computer. If your computer has a built-in CD-ROM drive and you didn’t receive floppy disks, you can find the Internal HD Format program on the CD-ROM disc that contains system software.
2 Open the Apple HD SC Setup icon. You may need to look in a folder called Utilities to find Apple HD SC Setup. 3 Click Drive until the disk you want appears. SCSI ID number of the currently selected hard disk Name of the currently selected hard disk 4 Click Test. 5 When a message tells you that testing is complete, click Quit.
2 Open the Disk First Aid icon. You may need to look in a folder called Utilities to find Disk First Aid. 3 Click the icon of the disk you want to test. Disk icons appear in a box at the top of the Disk First Aid window. 4 Click Repair to begin testing and repairing the disk. You can’t repair the startup disk or the disk that contains the Disk First Aid program, but you can test these disks by clicking Verify.
If Disk First Aid cannot correct the problem m Try repairing the disk again. Sometimes repeating the process corrects the problem. m Use another disk repair or recovery program. Some disk repair programs let you recover information from a damaged disk. m Consult a computer repair specialist for help. m Once you have recovered all the information you can, erase (reinitialize) the disk.
Installing or reinstalling system software System software is the set of programs and other files that your computer uses to start itself up, keep track of your files, and run the application programs you use. System software is kept in the folder called the System Folder. When you turn on your computer, it looks for a startup disk, which is a disk that contains the system software.
Installing system software Follow the steps in this section to do what is commonly called a “normal” installation of system software. If you’re installing system software on a hard disk for the first time, make sure that your hard disk has been initialized, a process that prepares the disk to store information. If you see the hard disk’s icon on the desktop when you start up the computer, the disk has been initialized.
5 Start up your computer from the Install Disk 1 disk or the CD-ROM disc that contains system software. See “Starting Up From a CD-ROM Disc” or “Starting Up From a Floppy Disk” in the section “Initializing a Hard Disk” earlier in this chapter. The Installer’s Welcome screen appears. You may have to double-click the System Software Installer icon to open the Installer program. 6 Click OK. The Easy Install dialog box appears.
10 When you see a message reporting that the installation was successful, click Restart. If a message reports that installation was not successful, try installing again. (Follow the instructions on the screen.) If, after reinstalling system software by doing a normal installation, you still experience problems with your computer, follow the steps in the next section for doing a “clean” installation of system software.
Testing your hard disk To prepare your hard disk for a clean installation, follow these steps: 1 Start up your computer from the Disk Tools disk or the CD-ROM disc that contains system software. See “Starting Up From a CD-ROM Disc” or “Starting Up From a Floppy Disk” in the section “Initializing a Hard Disk” earlier in this chapter. 2 Find and open the Disk First Aid icon. You may need to look in a folder called Utilities to find Disk First Aid.
The external SCSI hard disk is now prepared for reinstalling system software, and you can proceed with the installation. Installing new system software 1 Insert the Install Disk 1 disk into the floppy disk drive, or insert the CD-ROM disc that contains system software into the CD-ROM drive. The Installer’s Welcome screen appears. You may have to double-click the System Software Installer icon to open the Installer program. 2 Click Continue. The Easy Install dialog box appears.
4 Hold down Shift–x–K to start the clean installation. The following dialog box appears. 5 Click the Install New System Folder button and click OK. The Easy Install dialog box appears. The Install button has changed to Clean Install, and the contents of your old System Folder have been moved to a new folder named Previous System Folder. 6 Click Clean Install. Click here to install the software you need. 7 Follow the instructions that appear on the screen.
Replacing special software 1 Copy any special software items from the Previous System Folder back to your System Folder one item at a time, restarting the computer after copying each item. Special software consists of items such as control panels, system extensions, or custom utilities that you may have added to your System Folder. IMPORTANT Be very careful not to replace (copy over) any of the files in the System Folder with files from the Previous System Folder.
3 Choose Custom Install from the pop-up menu. The Custom Install dialog box appears, listing all available system software components. 4 Scroll through the list of components, clicking the checkbox next to each component you want to install. To get additional information about a component, click the box with the letter i in it to the right of the component.
5 Click Install. 6 Follow the instructions that appear on the screen. 7 When you see a message reporting that the installation was successful, click Quit. If a message reports that installation was not successful, try installing again. (Follow the instructions on the screen.) 8 Restart your Macintosh. The system software is installed and your computer is ready to use.
Read this appendix for important health and safety instructions, as well as tips on keeping your computer in good working order. Appendix A Health, Safety, and Maintenance Tips For your own safety and that of your equipment, follow all the instructions in this chapter. Keep these instructions available for reference by you and others.
Musculoskeletal discomfort As with any activity that involves sitting for long periods of time, using a computer can make your muscles sore and stiff. To minimize these effects, set up your work environment carefully, using the guidelines that follow, and take frequent breaks to rest tired muscles. To make working with your computer more comfortable, allow enough space in your work area so that you can change position frequently and maintain a relaxed posture.
Eye fatigue Eye fatigue can occur whenever the eyes are focused on a nearby object for a long time. This problem occurs because the eye muscles must work harder to view an object that’s closer than about 20 feet (6 meters). Improper lighting can hasten the development of eye fatigue. Although eye fatigue is annoying, there’s no evidence that it leads to permanent damage.
You may have to raise your chair so your forearms and hands are at the proper angle to the keyboard. If this makes it impossible to rest your feet flat on the floor, you can use a footrest with adjustable height and tilt to make up for any gap between the floor and your feet. Or you may lower the desktop to eliminate the need for a footrest. Another option is to use a desk with a keyboard tray that’s lower than the regular work surface. m Position the mouse at the same height as your keyboard.
Avoiding fatigue m Change your seated position, stand up, or stretch whenever you start to feel tired. Frequent short breaks are helpful in reducing fatigue. m Use a light touch when typing or using a mouse and keep your hands and fingers relaxed. m Some computer users may develop discomfort in their hands, wrists, or arms after intensive work without breaks. If you begin to develop chronic pain or discomfort in your hands, wrists, or arms, consult a qualified health specialist.
Safety instructions For your own safety and that of your equipment, always take the following precautions.
Handling your computer equipment Follow these guidelines for handling your computer and its components: m When setting up your computer, place components on a sturdy, flat surface, and carefully follow all setup instructions. m When connecting or disconnecting a cable, always hold the cable by its connector (the plug, not the cord). m Turn off your computer and all its components before connecting or disconnecting any cables to add or remove any component.
Handling the monitor Follow these procedures for handling a monitor: m Turn down the screen brightness control if you leave the computer turned on for extended periods. If the brightness is not turned down, the image on the screen could “burn in” and damage the screen. You can also use a “screen saver” program, which dims or varies the image on the screen when the computer has been idle for a specified period of time. These programs are available from independent suppliers and user groups.
Handling floppy disks Store disks at temperatures between 50° F and 125° F. Do not use a pencil or an eraser on a disk or disk label. Keep disks dry. 125° F (52° C) 50° F (10° C) Do not touch the exposed part of the disk behind the metal shutter. Keep disks away from magnets. Avoid exposing disks to extremely hot temperatures.
If you can’t eject a floppy disk If you can’t eject a floppy disk in the usual way, try the following in order: m Hold down the x and Shift keys and press the number 1 key on your keyboard to eject a disk in the internal disk drive. m Turn off the computer. If the disk isn’t ejected, then hold down the button on your mouse or other pointing device while you turn the computer on again.
Cleaning your equipment Follow these general rules when cleaning the outside of your computer and its components: m Use a damp, soft, lint-free cloth to clean the computer’s exterior. Avoid getting moisture in any openings. m Don’t use aerosol sprays, solvents, or abrasives. Cleaning the computer case To clean the case, do the following: 1 Turn off the computer completely and then disconnect the power plug. (Pull the plug, not the cord.
2 Turn the mouse upside-down and turn the plastic ring on the bottom counterclockwise to disengage it. If you have an older mouse, you may need to press the plastic ring (rather than turn it) to disengage it. 3 Turn the mouse right-side up with one hand and catch the ring and the ball with your other hand. 4 Clean the three small rollers inside the mouse with a cotton swab moistened with water. Rotate the rollers to clean all around them.
Read this appendix for instructions on installing an expansion card in you computer. Appendix B Installing an Expansion Card Expansion cards are printed circuit boards that can be installed in your computer to give it special capabilities, such as enhanced video capabilities, networking and communications, and additional processing power. You can install expansion cards by following the instructions that came with the card, or by following the instructions in this appendix.
Cards fit into slots on the computer’s logic board, the board that holds the components that make your computer work.
Installing an expansion card involves three steps: m opening the computer m inserting the card into a specific slot m closing the computer Opening the computer 1 Shut down your computer by choosing Shut Down from the Special menu. You can also press the Power key on the keyboard. 2 Unplug all the cables except the power cord from your computer. Leaving the power cord plugged in helps protect the computer from electrostatic discharge.
4 Pulling gently, swing the panel down, and slip it out. Remove the back panel. 5 If there are security screws on the vertical plate on the back of the computer, remove them with a Phillips screwdriver. If there are security screws, remove both screws from the vertical plate.
6 Unplug the power cord from your computer. 7 Swing the handle out from its storage position. Then grasp the handle and gently but firmly pull it toward you. The vertical plate and the logic board to which it’s attached slide all the way out of the computer. What you do next depends on the type of expansion card you want to install.
Installing a processor-direct slot (PDS) card 1 If your PDS (processor-direct slot) card has ports for connecting equipment, remove the plastic access cover from the vertical plate. Squeeze the two plastic tabs together and pull off the metal retainer so the access cover can come off. Metal retainer Vertical plate Processor-direct slot 2 Remove the PDS card from its static-proof bag. Hold the card by its edges to avoid touching any connectors on the card.
5 Press down on the card until the connector is solidly in place. Don’t force the card. If you meet resistance, pull the card out and try again. To see if the card is properly connected, lift it gently. If it resists and stays in place, it’s connected. Installing a communication card 1 If your communication card has ports for connecting equipment, remove the plastic access cover from the vertical plate. Push the two plastic tabs apart and pull off the metal retainer so the access cover can come off.
4 Align the card over the communication slot. Vertical plate Communication port access hole 5 Communication slot Press down on the card until the connector is solidly in place. Don’t force the card. If you meet resistance, pull the card out and try again. To see if the card is properly connected, lift it gently. If it resists and stays in place, it’s connected.
Closing the computer 1 Slip the base of the logic board into the guide rails inside the computer case and swing the handle back into its storage position. Make sure the logic board slides into the guides that are on both sides of the computer’s interior. Swing the handle up, into its storage position. 2 Press the reset button on the logic board, and then slide the logic board back into the computer. 1 Press the reset button.
3 If you removed security screws earlier, reinsert them now. Insert security screws here. 4 Slip the three hooks at the base of the back panel into the grooves on the computer case. Slip the three hooks on the back panel into the grooves in the computer case. 5 Swing the back panel up and snap it into place. Snap the plastic back panel into place.
6 Plug the cables back into the computer. 7 Reconnect the power cord. Your computer is now ready to turn on and use. WARNING Never turn on your computer unless all of its internal and external parts are in place. Operating the computer when it is open or missing parts can be dangerous, and can damage your computer.
Read this appendix to learn how to use the special keys on your keyboard. Appendix C Special Keys on Your Keyboard Your computer keyboard contains certain special keys that typewriter keyboards don’t have. Many of these keys allow you to give commands to the computer without using the mouse. For example, in many application programs, pressing the x (Command) key at the same time as the Q key is often an alternative method of quitting a program.
Special keys on Apple keyboards (continued) Control key control Delete key Use to delete selected material, or the character to the left of the insertion point. delete Enter key enter Escape key esc Function keys F1 Option key Numeric keys alt option num lock clear = / 7 8 9 4 5 6 1 2 * Use to produce numbers and mathematical symbols; some programs use these keys as function keys to initiate actions. Use to produce capital letters (or the upper character on the key).
If you can’t find what you’re looking for in this index, look in Macintosh Guide— available in the Guide (h) menu on your computer.
C cables connecting and disconnecting, safety instructions 81 for connecting external speakers 32 keyboard 6, 7 monitor 5 mouse 6, 7 Caps Lock key 99 carpal tunnel syndrome 76 CD-ROM disc, starting up the computer from 54–55 CD-ROM drive illustration 29 installing 34 CDs, playing 33 cleaning case 85 keyboard 82 monitor 79, 85 mouse 85–86 spills 81, 82 Clear key 99 clicking icons 27 clock, troubleshooting 43 close box 13 closing the computer 95–97 Command key 99 commands assigning to function keys 100 shortc
E Easy Install dialog box 66, 69, 70 ejecting disks 83–84 electrical grounding 2, 81 electrical safety 80 electromagnetic emissions 79 Enter key 100 erasing selected material 99, 100 error messages 39–40 Escape key 100 expanding memory 34 expansion card, installing 87–99 Extensions Manager control panel 47, 48 external SCSI hard disk, testing 60–61 external stereo speakers, connecting 32–33 eye fatigue related to computer use 77, 79 F files, backing up 38 Finder activating 13, 18, 25 automating tasks in 35
headphone jack, illustration 29 health tips 75–79 Help.
L logic board, slots on 88 Look For button (Macintosh Guide window) 19, 23–24 M Macintosh Guide menu 18 Macintosh Guide window appearance of 18 closing 25 expanding 25 Huh? button 25 Index button 19, 21–22 Look For button 19, 23–24 moving 25 moving to next step in 20 returning to 20, 25 searching for information in 19–24 shrinking and expanding 25 tips for using 25 Topics button 19–20 Macintosh Shortcuts window 27–28 Macintosh Tutorial 12–13 mathematical symbols 100 memory expanding 34 “not enough memory”
P R PC Exchange control panel 52, 53 PDS card access cover, illustration 30 plugging in the computer 1–2 the monitor 4 pointer. See arrow pointer ports Apple Desktop Bus (ADB) 6, 7, 50 Audio In (on speakers) 32 illustration 30 monitor 2 sound input 31 sound output 31, 32 posture for computer use 77–78 power button.
Show Balloons command (Guide menu) 26 showing windows on the desktop 38 Shut Down command (Special menu) 14 shutting down the computer.
diagnosing problems 40 ejecting floppy disks 84 error message 39–40 “frozen” screen 39, 41, 47 hard disk icon doesn’t appear on the desktop 45–46 icons don’t appear correctly on screen 46 installing system software 64–67 interference on screen or on a television or radio 82 keyboard connections 50 mouse connections 49 not enough memory 51 repairing damaged disks 59–63 “sad Macintosh” icon 45 screen is dark 43 SCSI device connections 44 starting up from a floppy disk 45 system software 9, 44 turning the comp
Apple Computer, Inc. 1 Infinite Loop Cupertino, California 95014-2084 408.996.1010 TLX 171-576 030-6199-A Printed in U.S.A.
