PowerBook G4 15-inch User’s Guide Includes setup, expansion, and troubleshooting information for your PowerBook G4 computer
K Apple Computer, Inc. © 2005 Apple Computer, Inc. All rights reserved. Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent of Apple. The Apple logo is a trademark of Apple Computer, Inc., registered in the U.S. and other countries. Use of the “keyboard” Apple logo (Option-Shift-K) for commercial purposes without the prior written consent of Apple may constitute trademark infringement and unfair competition in violation of federal and state laws.
1 Contents Chapter 1 5 6 12 14 16 17 18 Getting Started Setting Up Your PowerBook Basic Features of Your PowerBook Additional Features of Your PowerBook Putting Your PowerBook to Sleep or Shutting It Down Calibrating Your Battery Getting More Information Chapter 2 19 20 21 22 23 24 24 25 26 26 27 27 27 28 28 30 30 30 Getting to Know Your PowerBook Adjusting Your Display Using Your Power Adapter Using the Trackpad Using the Keyboard Using a Mouse Learning About Mac OS X Customizing Your Desktop and Se
3 44 44 47 47 51 51 55 Connecting With Ethernet (10/100/1000Base-T) Using Your Modem Using External Video Support (DVI, VGA, and S-Video) Connecting Speakers and Other Audio Devices Using Your SuperDrive Understanding Sudden Motion Sensor Using Your Battery Securing Your PowerBook Chapter 4 57 58 62 Adding Memory to Your PowerBook Installing Additional Memory Making Sure Your PowerBook Recognizes the New Memory Chapter 5 63 63 65 67 69 69 69 Troubleshooting Problems That Prevent You From Using Your
1 1 Getting Started Your PowerBook is a full-featured notebook computer. Your PowerBook includes the following components: ® DVI-to-VGA adapter S-video-to-composite adapter AC plug Phone cord Power adapter AC cord Important: Read all the installation instructions and safety information (see “Safety, Use, and Care Information” on page 73) carefully before you plug your computer in to a wall socket.
Setting Up Your PowerBook Your PowerBook is designed so that you can set it up quickly and start using it right away. The following pages take you through the setup process, including these tasks:  Plugging in the power adapter  Connecting the cables  Turning on your PowerBook  Configuring a user account and other settings using Setup Assistant Step 1: Plug In the Power Adapter If there is protective film around the power adapter, remove it before setting up your PowerBook.
Step 2: Connect Your Cables Next, for an Internet connection, connect your PowerBook to a phone line, DSL modem, cable modem, or Ethernet network. If you’re connecting to a wireless AirPort Extreme 802.11b or 802.11g network, you don’t need cables. To connect to a phone line: m Connect the phone cord from a wall jack to the internal modem port for a dial-up connection.
To connect to a DSL or cable modem or an Ethernet network: m Connect the cable to your DSL or cable modem as shown in the modem instructions, or connect the Ethernet cord to the Ethernet hub or outlet. Then connect the other end of the cord to the computer’s Ethernet port. Ethernet cord G Gigabit Ethernet port (10/100/ 1000 Base-T) Telephone cord ® Ethernet cord Step 3: Turn On Your PowerBook 1 To turn on the PowerBook, press the power button (®).
It takes the PowerBook a few moments to start up. After it starts up, the sleep indicator light turns off, and Setup Assistant opens automatically. Note: To start up your PowerBook, press the power button (®) only once briefly (up to 1 second). Do not continue to hold down or press the power button after the startup tone or you might cause the computer to shut down again. 2 Use your PowerBook trackpad to select and move items on the screen, just like you use a mouse with a desktop computer.
Problems Turning On the Computer? Nothing happens when you press the power button (®). Â The battery might be drained. Make sure that you plugged the power adapter firmly in to both the computer and a power source. The plug should light when you plug it in to the computer. Â If the computer still doesn’t start up, see “Problems That Prevent You From Using Your Computer” on page 63. You see a picture of a disk or a folder with a blinking question mark.
Using Setup Assistant, you can transfer:  User accounts, including preferences and email  Network settings, so your new PowerBook is automatically set up to work with the same network settings as your other Mac  Files and folders on the hard disk and partitions. This gives you easy access to the files and folders you used on your old Mac.  The Applications folder, so most of the applications you used on your other Mac are now on your new PowerBook.
Basic Features of Your PowerBook AirPort Extreme/ Bluetooth antenna window AirPort Extreme/ Bluetooth antenna window Built-in speaker (located under speaker grille) Microphone ® Power button ® Function key (Fn) Built-in speaker Sleep indicator light Display release button Trackpad button — Mute F1 ¤ Brightness controls 12 F2 F3 Slot-loading optical drive Media Eject key Video Mode Toggle key control esc Trackpad F4 F5 - Volume controls Chapter 1 Getting Started num lock F6 Num Lock
¤ Brightness controls Increase or decrease the brightness of your PowerBook display. — Mute control Mute the volume of the sound coming from the built-in speakers and headphone port. - Volume controls Increase or decrease the volume of the sound coming from the speakers and headphone port. Num Lock key Activate the numeric keypad embedded in the PowerBook keyboard. When the numeric keypad is activated, a green light glows on the key.
Additional Features of Your PowerBook ® d USB 2.0 ¯ Power adapter port f Headphone/ optical digital audio out port port W Internal , Audio line in/optical modem port PC Card slot digital audio in port ® H FireWire G Gigabit Ethernet port (10/100/1000Base-T) 400 port Security slot 14 d USB 2.
¯ Power adapter port Plug in the included power adapter to recharge your PowerBook battery. W Internal modem port Connect a standard phone line directly to the internal modem. d Two Hi-Speed USB 2.0 (Universal Serial Bus) ports Connect additional equipment to your PowerBook, such as printers, external storage devices, digital cameras, modems, keyboards, and joysticks. (Compatible with standard USB devices.
Putting Your PowerBook to Sleep or Shutting It Down When you finish working with your PowerBook, you can put it to sleep or shut it down. Putting Your PowerBook to Sleep If you will be away from your PowerBook for only a short time, put the computer to sleep. When the computer is in sleep, you can quickly wake it and bypass the startup process. To put the computer to sleep, do one of the following: m Close the display. m Choose Apple () > Sleep from the menu bar.
Shutting Down Your PowerBook If you aren’t going to use your PowerBook for a day or two, shut it down. To shut down your computer, do one of the following: m Choose Apple () > Shut Down from the menu bar. m Press the power button (®) and click Shut Down in the dialog that appears. The sleep indicator light goes on briefly during the shutdown process.
If you purchased additional batteries, follow the calibration procedure with the additional batteries as well. For more information about your power adapter and battery, see “Using Your Power Adapter” on page 21 and “Using Your Battery” on page 51. Getting More Information For more information about your PowerBook, check out these resources: Â Learn the important basics about your PowerBook. Check out Chapter 2, “Getting to Know Your PowerBook,” on page 19.
2 Getting to Know Your PowerBook 2 This chapter introduces important basics about your PowerBook. Because your PowerBook is so thin and light, you can take it with you to the office, library, class, or wherever you work or play. Whenever you stop using your PowerBook, wait a few moments to let the hard disk and any optical disc (such as a CD or DVD) in your drive stop spinning before you transport the computer. Avoid jostling or bumping your PowerBook while discs are spinning.
Adjusting Your Display After you begin working with your new PowerBook, you might need to adjust your display so that the screen is easier to see. Use the keys labeled with the brightness icon (¤) to adjust screen brightness. ¤ Brightness controls Keyboard illumination controls ® To turn off the automatic display brightness feature: m Choose Apple () > System Preferences from the menu bar. Open the Displays pane and deselect the “Automatically adjust brightness as ambient light changes” checkbox.
You can choose scaled resolutions in the Displays pane of System Preferences. When you switch to a scaled resolution, items on the screen appear larger, making them easier to see. Scaled resolutions might not be as sharp as the display’s default resolution. To adjust the resolution on your display: m Choose Apple () > System Preferences from the menu bar. Open the Displays pane of System Preferences. To control your display settings using the Displays icon in the menu bar, click “Show displays in menu bar.
For best results, always connect your AC cord and use a grounded outlet when one is available. Use only the AC cord that came with your power adapter. Make sure to push the power plug snugly into the power adapter port on the computer to ensure it is engaged and power is flowing to the computer. If the cord is plugged in properly, you will see an indicator light on the end of the cord that plugs in to your PowerBook.
Using the Keyboard Your PowerBook keyboard has a numeric keypad incorporated in the standard keyboard keys. Keys used for the numeric keypad have a smaller secondary label. Num Lock key Numeric keypad ALS sensor ® ALS sensor To use the numeric keypad, press the Num Lock key. The Num Lock key glows green, indicating that the keypad is active. When you finish using the keypad, press the Num Lock key again to turn it off.
If you like to use keyboard shortcuts to work efficiently, choose Help > Mac Help from the menu bar and search for “navigation shortcuts.” You’ll find a list of keyboard shortcuts for many common procedures and applications. Using a Mouse If you have an Apple mouse with a USB connection, you can insert the USB connector into the USB 2.0 port and use your mouse right away. If you have an Apple wireless mouse, see “Using Bluetooth Wireless Technology” on page 40 for information about connecting it.
Customizing Your Desktop and Setting Your Preferences You can quickly make your desktop look the way you want using System Preferences. Choose Apple () > System Preferences from the menu bar. Feel free to make changes and experiment with the following: Â Appearance: Select this preference pane to change the colors of buttons, menus, windows, and highlight colors, among other options.
Getting Answers Using Mac Help Most of the information about using your Macintosh is available right on your computer in Mac Help. To access Mac Help: 1 Click the Finder icon in the Dock (the bar of icons at the bottom of the screen). 2 Choose Help > Mac Help (click the Help menu in the menu bar and choose Mac Help). 3 Click in the search field, type a question, and press Return on your keyboard.
When an Application Does Not Respond On rare occasions, an application may “freeze” on the screen. Mac OS X provides a way to quit a frozen application without restarting your computer. Quitting a frozen application might allow you to save your work in other open applications. To force an application to quit: 1 Press Command (x)-Option-Esc or choose Apple () > Force Quit from the menu bar. The Force Quit Applications dialog appears with the application selected. 2 Click Force Quit.
Keeping Your Software Up to Date You can connect to the Internet and automatically download and install the latest free software versions, drivers, and other enhancements from Apple. When you are connected to the Internet, Software Update checks Apple’s Internet servers to see if any updates are available for your computer. You can set your Mac to check the Apple server periodically and download and install updated software. To check for updated software: 1 Open System Preferences.
After you connect a USB or FireWire printer, your computer usually detects it automatically and adds it to the list of available printers. You might need to know the network name or address of printers connected to a network before you can print to them. Use the Print & Fax pane of System Preferences to select your printer. To set up a printer: 1 Open System Preferences and click the Print & Fax icon. 2 Click Printing and then click the Add button (+) to add a printer.
Playing a CD and Connecting Headphones You can use iTunes, an easy-to-use music player, to listen to your iTunes music and CDs while you work. Insert a music CD in your optical drive and iTunes appears automatically on the screen. You can listen to your music on the PowerBook internal speakers or connect headphones with a minijack to the headphone port of your PowerBook for private listening right away. To learn more about iTunes: m Open iTunes and choose Help >” iTunes and Music Store Help.
 If you connect your computer to a network using Ethernet, you can transfer files to another computer on a network. You can access a server or another computer by clicking Network in the Finder sidebar, or by choosing Go > Connect to Server from the menu bar.  You can create a small Ethernet network by connecting an Ethernet cable from your PowerBook to another computer’s Ethernet port. After you’re connected, you can transfer files directly from one computer to the other.
3 Using Your PowerBook 3 Your PowerBook has many built-in features and connection capabilities. These include the following: Â Universal Serial Bus (USB) 2.0 ports for connecting additional equipment such as printers, scanners, and other devices. See “Using Universal Serial Bus (USB) Devices” on page 34. Â FireWire 400 and 800 ports for connecting high-speed equipment such as digital videocameras and external hard drives. See “Connecting With FireWire” on page 36. Â A PC Card/CardBus slot.
Using Universal Serial Bus (USB) Devices Your PowerBook comes with two USB 2.0 ports (d), also referred to as Hi-Speed USB, which you can use to connect many types of external devices, including printers, scanners, digital cameras, game pads, joysticks, keyboards, and floppy disk drives. Your USB 2.0 ports are compatible with earlier USB devices. In most cases, you can connect and disconnect a USB device while the computer is running. After you connect the device, it is ready to use.
Using Multiple USB Devices at the Same Time You can purchase a USB hub to connect multiple USB devices to your computer. The USB hub connects to an open USB port on your computer and provides additional USB ports (usually four or seven). Hi-Speed hubs can support USB 2.0 Hi-Speed devices as well as USB 1.1 compatible devices. USB 1.1 hubs don’t allow Hi-Speed USB devices to operate at their maximum data speed. Some USB hubs have a power adapter and should be plugged in to an outlet.
Connecting With FireWire Your computer has one FireWire 400 and one FireWire 800 port (H). With FireWire, you can easily connect and disconnect external high-speed devices—such as digital video (DV) cameras and hard disks—without restarting your computer. You can connect a standard 6-pin FireWire device directly to the FireWire 400 port (H). You can use a 9-to-6-pin FireWire cable to connect the device to the FireWire 800 port (H).
Using FireWire Devices To use a FireWire device with your computer, connect the device to the computer and install any software that came with the device. Your computer automatically detects newly connected devices. Note: If your PowerBook cannot find the correct software when you connect a FireWire device, you can either install the software that came with the device or follow the onscreen prompts to use the Internet to locate, download, and install the correct software.
4 When you finish transferring files, drag the PowerBook hard disk icon to the Trash. 5 Press the power button (®) on the PowerBook to shut it down, and then disconnect the FireWire cable. Getting More Information About FireWire Additional information about FireWire is available in Mac Help. Choose Help > Mac Help in the Finder menu bar and search for “FireWire.” You can also find information on the Apple FireWire website at www.apple.com/firewire.
Inserting and Ejecting a PC Card When inserting a PC Card, make sure the label is facing up and the card is level. You’ll feel some resistance as you slide in the card. When the card is firmly seated in the slot, it clicks into place and an icon appears on the desktop. You can eject a PC Card when your computer is on or off, but not when it is in sleep. To eject a PC Card: 1 If the computer is turned on, drag the card’s icon to the Trash. 2 Push the PC Card Eject button once to release the button.
Getting Wireless Internet Access With AirPort Extreme With AirPort Extreme, you set up a wireless connection to a device known as a base station, which has a physical connection to the Internet. AirPort Extreme technology works like a cordless phone. The AirPort Extreme technology in the computer makes a wireless connection to the AirPort, AirPort Extreme, or AirPort Express base station, which is connected to the phone line, a DSL or cable modem, or a local-area network with Internet access.
Bluetooth wireless technology eliminates the need for many cables that traditionally connect devices together. Bluetooth enabled devices can connect to each other wirelessly at distances up to 33 feet (10 meters). With Bluetooth wireless technology, you can do the following: Â Use your PowerBook to communicate with a compatible Bluetooth enabled mobile phone.
Setting Up Bluetooth File Exchange You can control how your computer handles files that are exchanged between it and other Bluetooth enabled devices. You can choose a folder for the files you accept from other devices, a folder for other devices to browse, and which applications to use to open the files you accept. To set up Bluetooth File Exchange: 1 Open System Preferences and click Bluetooth. 2 Click Sharing.
Connecting With Ethernet (10/100/1000Base-T) Your computer comes with built-in Ethernet networking capability, which you can use to connect to a network or to a cable or DSL modem. ® Connecting to a network gives you access to other computers. You might be able to store and retrieve information; use network printers, modems, and email; or connect to the Internet. You can use Ethernet to share files between two computers or set up a small network.
Getting More Information About Using Ethernet Additional information, including setting up an Ethernet network and transferring files using Ethernet, is available in Mac Help. Choose Help > Mac Help and search for “Ethernet” or “network.” For information about networking products you can use with your PowerBook, check the Macintosh Products Guide at www.apple.com/guide. Using Your Modem Your computer comes with an Apple 56K v.92 modem installed.
If the device you want to connect has a composite port rather than an S-video port, you can use the S-video-to-composite adapter that came with your PowerBook. DVI port ® S-video out port When an external monitor or TV is connected, you can either have the same image appear on both the internal display and the external monitor (known as video mirroring) or use the external monitor to extend the size of the Mac OS desktop (known as dual-display mode).
To connect an external display or projector with a VGA connection to your computer: 1 Turn on the external display or projector. 2 Make sure the display cable is connected to the external projector or display. 3 Connect the DVI-to-VGA adapter that came with your PowerBook to the VGA connector of the external display or projector, and then connect the adapter to your PowerBook. Your PowerBook automatically detects the external display.
Connecting an Apple Flat-Panel Display You can connect your PowerBook to an Apple flat-panel display. Depending on the display used, the connection might require a DVI-to-ADC adapter, available from your Apple Authorized Reseller, an Apple Store retail location, or the online Apple Store at www.apple.com/store. Getting More Information About Using an External Monitor or TV Additional information about using and configuring an external monitor is available in Mac Help.
 Write music, documents, and other digital files to CD-R and CD-RW discs  Play DVD movies and use most DVD discs (single- and double-layer)  Record information on blank single-layer DVD-R, DVD-RW, and DVD+RW discs; and on single- and double-layer DVD+R discs Important: The SuperDrive in your PowerBook supports standard circular 12 cm discs. Irregularly shaped discs or discs smaller than 12 cm are not supported. Noncircular discs can become lodged in the drive.
2 When the disc icon appears on the desktop, the disc is ready to use. Ejecting a Disc To eject a disc, do one of the following: Â Drag the disc icon to the Trash. Â Press and hold the Media Eject key (C) on the keyboard until the disc ejects. Allow the disc to fully eject before removing or reinserting it. If you can’t eject the disc, quit any applications that might be using the disc and try again. If that doesn’t work, restart the computer while holding down the trackpad button.
To record music from your iTunes library: 1 Click the iTunes icon in the Dock. 2 Select the playlist you want to record. 3 Insert a blank CD-R or CD-RW disc. 4 At the top of the iTunes window, click Burn CD. Important: If your battery runs down when you are burning a CD, the burn can fail and you will not be able to use the CD disc again. To prevent this, always use your power adapter when burning a CD. Recording Information on a DVD You can record your own digital movies on a blank recordable DVD disc.
Getting More Information For more information about DVD Player and iTunes, consult these resources: Â For instructions about using DVD Player, open DVD Player and choose Help > DVD Player Help from the menu bar. Â For information about how to use iTunes to record music files on a CD-R or CD-RW disc, choose Help > “iTunes and Music Store Help” from within iTunes.
Note: If you have installed additional memory in your PowerBook, it may only provide power for less than three minutes. Also, changing batteries several times in a short period can further reduce this length of time. Important: If only one flashing light is on, very little charge is left. If no lights are visible, the battery is completely drained and the computer will not start up unless the power adapter is connected.
2 Turn over the PowerBook and locate the battery latch. Use a coin to turn the latch one quarter turn clockwise to unlock the battery, and gently remove it. Latch To replace the battery: m Place the right side of the battery into the battery compartment. Gently press the left side of the battery down until the battery latch locks. Note: Dispose of batteries according to your local environmental laws and guidelines. For more information, see “Disposal and Recycling Information” on page 100.
Charging a Battery When the power adapter that came with your computer is connected, the battery recharges whether the computer is off, on, or in sleep. However, the battery recharges more quickly if the computer is off or in sleep. When the PowerBook is on, you can monitor the battery charge level using the Battery status icon in the menu bar.
 Your PowerBook is preset to automatically reduce its processing speed during periods of light processing activity when using battery power, thus reducing power usage. The setting that determines this is the Normal option in the Optimization pop-up menu of the Energy Saver pane of System Preferences. During periods of high processing activity, your computer will automatically switch to a higher processing speed.
4 Adding Memory to Your PowerBook 4 This chapter provides information and instructions for installing additional memory in your PowerBook. Warning: Apple recommends that you have an Apple-certified technician install memory. Consult the service and support information that came with your computer for instructions on how to contact Apple for service. If you attempt to install memory and damage your equipment, such damage is not covered by the limited warranty on your computer.
Installing Additional Memory Step 1: Removing the Battery 1 Shut down your PowerBook. Disconnect the power adapter, phone cord, and any other cables connected to the computer. 2 Turn over the PowerBook and remove the battery by turning the latch a quarter turn. Latch ª 58 Warning: The internal components of your PowerBook can be hot. If you have been using your PowerBook, wait 10 minutes after shutting down to let the internal components cool before continuing.
Step 2: Installing Memory 1 Using a Phillips size 00 screwdriver, unscrew the memory door and remove it from the bottom of your computer. 2 Touch a metal surface inside the computer to discharge any static electricity from your body. 3 If you already have a memory card installed in the slot, remove it. Spread the tabs in the slot away from the notches in the memory card. The card should pop up slightly. Lift the memory card to a 30-degree angle and then gently slide the card out of the memory slot.
4 Insert the new memory card into the slot at a 30-degree angle. Push the card to seat it fully in the slot. 30O 5 Press down on the memory card to lock it in place. If the memory card does not latch, do not force the card down. Try reinserting the card to make sure it is fully seated.
6 Replace the memory door and screw it in place. Note: To avoid damage, be careful not to overtighten the screws. Step 3: Replacing the Battery 1 Place the left side of the battery in the battery compartment. Gently press the right side of the battery down until the battery latch locks into place. 2 Reconnect the power adapter and any other cables that were attached.
Making Sure Your PowerBook Recognizes the New Memory After installing additional memory in your PowerBook, check whether the computer recognizes the new memory. To check the computer’s memory: 1 Start up your computer. 2 When you see the Mac OS desktop, choose Apple () > About This Mac. Total memory installed in your PowerBook The total memory includes the amount of memory that originally came with the computer plus the new memory you added.
5 Troubleshooting 5 If you have a problem working with your PowerBook, check here first for solutions and advice. When you experience a problem working with your PowerBook, there is usually a simple and quick solution. Be aware of the conditions that led up to the problem. Making a note of things you did before the problem occurred will help you narrow down possible causes and then find the answers you need. Note the following: Â The applications you were using when the problem occurred.
 If the computer still doesn’t respond, try to restart it by simultaneously pressing the Command (x) and Control keys on your keyboard and the power button (®). If the problem occurs frequently, choose Help > Mac Help from the menu bar at the top of the screen. Search for the word “freeze” to get help for instances when the computer freezes or doesn’t respond.
 If you are still unable to start up your computer, see the service and support information that came with your PowerBook for information about contacting Apple for service. If the display suddenly goes black or your system freezes Try restarting your system. 1 Unplug any devices that are connected to your PowerBook except the power adapter. 2 Hold down the Command (x) and Control keys and press the power button (®) to restart the system.
 Make sure you are within antenna range of the other computer or the network’s access point by checking the AirPort Extreme or AirPort Express signal level. Check the AirPort status icon in the menu bar. Up to four bars appear to show signal strength. Nearby electronic devices or metal structures can interfere with wireless communication and reduce this range. Repositioning or rotating the computer might improve reception.
Reinstalling the Software That Came With Your Computer Use the software installation discs that came with your computer to reinstall Mac OS X and any applications that came with your computer, as well as to install Mac OS 9 support for running the Classic environment (if you want to use Classic applications with your computer). Important: Apple recommends that you back up the data on your hard disk before reinstalling software. Apple is not responsible for any lost data.
Installing Applications To install just the applications that came with your computer, follow the steps below. Your computer must have Mac OS X already installed. 1 Back up your essential files. 2 Make sure your power adapter is plugged in. 3 Insert the Mac OS X Install Disc 1 that came with your computer. 4 Double-click Install Bundled Software Only. 5 Follow the onscreen instructions. 6 After selecting the destination disk for installation, continue following the onscreen instructions.
Using Apple Hardware Test You can use Apple Hardware Test to help determine if there is a problem with your computer’s hardware. To use Apple Hardware Test: 1 Disconnect all external devices from your computer except the power adapter. If you have an Ethernet cable connected, disconnect it. 2 Insert the Mac OS X Install Disc 1 that came with your computer. 3 Restart your computer and hold down the Option key as it starts up. A list of available startup volumes appears.
Specifications A Appendix A You can use System Profiler to find out detailed information about your PowerBook, such as the amount of built-in memory, hard disk size, devices connected, and the product serial number. To access the information in System Profiler, choose Apple () > About This Mac from the menu bar and then click More Info, or open System Profiler, located in Applications/Utilities. Click the triangles in the window to show and hide information in the different categories.
Power Adapter  Input: AC 100–240 volts (V), 50/60 hertz (Hz)  Output: DC 24.5 V, 2.65 A Battery  Output: DC 10.8 V  Capacity: 50 WHr  Additional information is available on the Internet at www.apple.com/powerbook and www.apple.com/support.
Safety, Use, and Care Information B Appendix B Read this important PowerBook safety and maintenance information. Safety Instructions for Setting Up and Using Your Computer Be aware of the following safety tips and warnings as you work with your PowerBook. Plugging In the Power Adapter Always leave space around your power adapter. Do not use this equipment in a location where airflow around the power adapter or computer is confined.
Using Connectors and Ports Never force a connector into a port. If the connector and port don’t join with reasonable ease, they probably don’t match. Make sure that the connector matches the port and that you have positioned the connector correctly in relation to the port. Using Your PowerBook When you’re using your PowerBook or charging the battery, it is normal for the bottom of the case to get warm. For prolonged use, place your PowerBook on a flat, stable surface.
Cleaning Your PowerBook Follow these general rules when cleaning the outside of your computer and its components: Â Shut down your PowerBook and remove the battery. Â Use a damp, soft, lint-free cloth to clean the computer’s exterior. Avoid getting moisture in any openings. Do not spray liquid directly on the computer. Â Don’t use aerosol sprays, solvents, or abrasives. Cleaning Your PowerBook Display To clean your PowerBook screen, do the following: Â Shut down your PowerBook and remove the battery.
Make sure that you always do the following: Â Keep your computer away from sources of liquids, such as drinks, washbasins, bathtubs, shower stalls, and so on. Â Protect your computer from dampness or wet weather, such as rain, snow, and so on. Â Read all the installation instructions carefully before you plug your computer in to a wall socket. Â Keep these instructions handy for reference by you and others. Â Follow all instructions and warnings dealing with your computer.
Understanding Ergonomics Here are some tips for setting up a healthy work environment. Keyboard and Trackpad When you use the keyboard and trackpad, your shoulders should be relaxed. Your upper arm and forearm should form an angle that is slightly greater than a right angle, with your wrist and hand in roughly a straight line. This Not this Use a light touch when typing or using the trackpad and keep your hands and fingers relaxed. Avoid rolling your thumbs under your palms.
You might have to raise your chair so that your forearms and hands are at the proper angle to the keyboard. If this makes it impossible to rest your feet flat on the floor, you can use a footrest with adjustable height and tilt to make up for any gap between the floor and your feet. Or you might lower the desktop to eliminate the need for a footrest. Another option is to use a desk with a keyboard tray that’s lower than the regular work surface.
Connecting to the Internet C Appendix C You can use your computer to browse the World Wide Web, send email to friends and family, and chat in real time over the Internet. Use this detailed guide to connect to the Internet. When you first start up Mac OS X, Setup Assistant helps you enter your Internet configuration information. If you didn’t use Setup Assistant to configure your Internet connection, you can use it now. Open System Preferences and click Network.
To find the settings on a Mac OS X computer: Â Open the Network pane of System Preferences. Â Choose your connection method from the Show pop-up menu. Â Copy the information for your configuration. To find the settings on a Mac OS 9 computer: Â Open the TCP/IP control panel. Â Find the connection method in the “Connect via” pop-up menu. Â Find the configuration in the Configure pop-up menu. Â Copy the IP address, subnet mask, and router address from the corresponding fields.
Gathering the Information You Need You can write the information you get from your ISP, your network administrator, or your other computer on these pages, and then enter it in Network Setup Assistant.
If you selected “PPP” (for PPPoE connections), gather the following:  Service provider  Account name  Password  PPPoE service name The information below is optional. Ask your ISP or system administrator if you need it.
3 Choose Network Port Configurations from the Show pop-up menu and select the On checkbox next to Internal Modem. 4 Drag Internal Modem to the top of the Port Configurations list to make it the preferred, or primary, network interface. 5 Choose Internal Modem from the Show pop-up menu and click PPP. 6 Enter the information from your ISP and click Apply Now.
To test your Internet configuration: 1 Open the Internet Connect application (in the Applications folder). 2 Click the Internal Modem icon, if necessary. 3 Enter your dial-up phone number, account name, and password, if necessary. 4 Click Connect. Internet Connect dials your ISP and establishes a connection. To connect automatically when you start a TCP/IP application, such as a web browser or email: 1 Click PPP Options (in the PPP pane of Network preferences).
Make sure you have the information from your ISP available as you configure your network (see page 81). To set up Network preferences for the built-in Ethernet port: 1 Choose Apple () > System Preferences from the menu bar. 2 Click Network. 3 Choose Network Port Configurations from the Show pop-up menu. 4 Select the On checkbox next to Built-in Ethernet. 5 Drag Built-in Ethernet to the top of the Port Configurations list to make it the preferred, or primary, network interface.
Configuring Manually Have your static IP address, router address, and subnet mask from your ISP ready (see page 81). To set up a manual configuration: 1 In Network preferences, choose Built-in Ethernet from the Show pop-up menu. 2 Click TCP/IP, if necessary. 3 In the Configure IPv4 pop-up menu, choose Manually. 4 Type the information in the corresponding fields. 5 Click Apply Now. After you configure your network, your connection is ready.
Configuring DHCP After you set up a DHCP configuration, the DHCP server automatically provides your network information. To set up a DHCP configuration: 1 In Network preferences, choose Built-in Ethernet from the Show pop-up menu. 2 Click TCP/IP, if necessary. 3 Choose Using DHCP from the Configure IPv4 pop-up menu. 4 Click Apply Now. Open your web browser (or another TCP/IP application) to test your Internet connection.
Configuring PPPoE Some DSL-based ISPs use Point-to-Point Protocol over Ethernet (PPPoE). If you use a DSL modem and need a user name and password to connect to the Internet, check with your ISP to determine if you should connect using PPPoE. To set up a PPPoE connection: Have your user name, password, and if required, the domain name server (DNS) address from your ISP available (see page 81). 1 In Network preferences, choose Built-in Ethernet from the Show pop-up menu.
5 Type the domain name server (DNS) addresses in the DNS Servers field. 6 Click Apply Now. After you configure your network, your Internet connection is ready. You can open your web browser or other TCP/IP application to test your connection. Important: If you did not select the option to connect automatically, you will need to open the Internet Connect application, choose the correct configuration, and then click Connect.
To check if you have access to an AirPort Extreme network: m Click the AirPort status icon in the menu bar and choose an AirPort network listed there. If you don’t see an AirPort network listed, you can use AirPort Setup Assistant to check or change your settings, or you can change them using the Network pane of System Preferences.
To set up Network preferences for an AirPort Extreme connection: 1 Choose Apple () > System Preferences from the menu bar. 2 Click Network. 3 Choose Network Port Configurations from the Show pop-up menu. 4 Select the On checkbox next to AirPort. Next, follow the instructions to configure your network either manually or using DHCP, as instructed by your ISP or network administrator.
7 In the Configure IPv4 pop-up menu, choose either Manually or Using DHCP. Â If you chose Manually, type the other information in the corresponding fields. Â If you chose Using DHCP, you don’t need to enter any further information unless your system administrator has instructed you to do so. 8 Click AirPort and select options for joining an AirPort Extreme network after restarting or when your computer wakes from sleep. 9 Click Apply Now. After you configure your AirPort settings, you are ready to connect.
Troubleshooting Your Connection If you’re having problems with your Internet connection, refer to the suggestions in the following sections for the type of connection you have. Cable Modem, DSL, and LAN Internet Connections If you can’t connect to the Internet using your cable modem, DSL, or local area network (LAN), see the following instructions. Important: Instructions that refer to modems do not apply to LAN users.
Network Connections If you have two or more computers attempting to share an Internet connection, be sure that your network is set up properly. You need to know if your ISP provides only one IP address or if it provides multiple IP addresses, one for each computer. If only one IP address is used, then you must have a router capable of sharing the connection, also known as network address translation (NAT) or “IP masquerading.
Top Ten Questions D Appendix D Do you have a question? Here are the top ten questions commonly asked by new PowerBook users. My Internet connection doesn’t seem to be working. How do I set it up? There are different types of Internet connections. For example, you can connect using a modem, a DSL connection, a wireless AirPort connection, or an Ethernet network. You will need to supply Mac OS X with specific information about your connection type, Internet service provider, or network.
If you sent a print job to your printer, but it’s not printing, check to see if the print job is stopped or on hold by clicking the printer icon in the Dock. (If no icon appears in the Dock, open Printer Setup Utility in the Applications/Utilities folder and double-click the printer’s name.) If the window for the printer says “Job Stopped,” click the Start Jobs button. If “Hold” appears beside the job name, resume printing by clicking the job name and clicking Resume.
How do I connect a monitor or TV to my PowerBook? Your PowerBook comes with an external monitor port and adapters for connecting many commonly used monitors, TVs, and video displays. If your device has a connector that is different from the external monitor port on your PowerBook, you need to attach an adapter to connect it to the port. To see the adapters included with your PowerBook, see page 5.
Communications Regulation Information FCC Compliance Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. See instructions if interference to radio or television reception is suspected.
Laser Information Warning: Making adjustments or performing procedures other than those specified in your equipment’s manual may result in hazardous radiation exposure. Do not attempt to disassemble the cabinet containing the laser. The laser beam used in this product is harmful to the eyes. The use of optical instruments, such as magnifying lenses, with this product increases the potential hazard to your eyes. For your safety, have this equipment serviced only by an Apple-authorized service provider.
Telephone and Apple 56K Modem Information Notify Your Telephone Company Some telephone companies require that you notify the local business office when you hook up a modem to their lines. Information You Need in the United States The internal modem complies with Part 6B of the FCC rules. On the back of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN). If requested, provide this information to your telephone company.
Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority or electrician. Â Load number: 0.1 The load number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to the telephone loop that is used by the device, to prevent overloading.
Information You Need in Australia All telecommunications devices are required to be labelled as complying to the Australian telecommunications standards, ensuring the health and safety of the operator and the integrity of the Australian telecommunications network.
A about your battery 17 AC cord 6, 21 AC plug 6, 21 adjusting your display 20 AirPort antenna window 13 AirPort Express 39, 40 AirPort Extreme base station 40 problems 65 setting up a connection 81, 89 technology 39 ALS system 23 amber light 21 ambient light-sensing system 23 analog phone line 7, 44 Appearance preferences 25 Apple 56K internal modem 44 application freeze 27 applications 26 audio line in port 15 B base station, AirPort 40 battery calibrating 17 charging 54 conservation 54 conserving power 9
flat-panel display 47 headphones 30 to Internet 11 a monitor or TV 97 modem 44 a printer 28 projector 45 a TV 46 two computers 36, 37 USB printers 34 VCR 46 a video device 46 videocameras 36 wirelessly 39 conserving battery power 96 controls brightness 13 keyboard 13 volume 13 cord, AC 6 D Dashboard 13, 24 Dashboard & Exposé preferences 25 default resolution 20 Desktop & Screen Saver preferences 25 DHCP.
internal modem 44 Internet configuration 84 connecting to 11 connecting using Setup Assistant 89 connection problems 66, 95 inventory of items 5 K keeping the display closed 46 keyboard illumination 23 illumination controls 13 L LAN connection 81, 82, 84 locating your serial number 69 M Mac OS X interface 96 learning about 24 manual Internet configuration 86 manually using DHCP router option 81 Media Eject key 13 memory checking 62 installing 57, 58 screwdriver required 59 specifications 57 microphone 13
computer won’t turn on 64 display goes black 65 hard disk 66 Internet connection 66, 93 pointer won’t move 63 PPPoE connections 93 trouble ejecting a disc 66 trouble using AirPort 65 turning the computer on 10 with an application 65 See also troubleshooting processing speed 57 putting your PowerBook to sleep 16 R RAM 58 recording CD-R 49 CD-RW 49 DVD 50 music 49 reinstalling 97 removing the battery 52 replacing the battery 52 resetting your password 65, 97 RJ-11 cable 44 S safety general instructions 75 p
U Universal Serial Bus.
