X3_UG.
Declaration of Conformity FCC Warning Manufacturer: InFocus Corporation, 27700B SW Parkway Ave. Wilsonville, Oregon 97070 USA European Office: Strawinskylaan 585, 1077 XX Amsterdam, The Netherlands We declare under our sole responsibility that this projector conform to the following directives and norms: Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
If you are experienced in setting up projection systems, use the Quick Setup card that is included with the projector. For complete details on connecting and operating the projector, refer to this User’s Guide. Electronic versions of this User’s Guide in multiple languages are available on the included CD. The most current versions can be found on our website.
Important Operating Considerations for Safety • Place the projector in a horizontal position no greater than 15 degrees off axis. • Locate the projector in a well-ventilated area without any obstructions to intake or exhaust vents. Do not place the projector on a tablecloth or other soft covering that may block the vents. • Locate the projector at least 4' (1.2 m) away from any heating or cooling vents. • Use only InFocus-approved ceiling mounts. • Use only the power cord provided.
Introduction speaker keypad Your new digital projector is simple to connect, easy to use, and straightforward to maintain. It is a versatile projector that is flexible enough for business presentations and home video viewing too.
Connector Panel The projector provides both computer and video connection options, including: • M1 for computer and video • S-video • Composite RCA audio/video RCA audio/visual The projector also provides the following connectors: • Monitor out • Audio out • 12 volt DC output (see below) 12 volt DC output 12 volt DC output +12v The 3.5mm mini-jack trigger provides a 12 volt DC output. It provides a constant output while the projector is on. It has numerous uses.
Positioning the projector .5 12 • • • ft . Position the projector within 10 feet (3m) of your power source and within 6 feet (1.8m) of your video device (unless you purchase extension cables). To ensure adequate cable access, do not place the projector within 6 inches (.15m) of a wall or other object. 4.8 ft. Projection angle in 4:3 mode (default) Position the projector the desired distance from the screen.
Projector and Device Connector Guide The following illustration and table should help you find the connectors to use and obtain the best resolution possible from your input devices, such as computers, standard VCRs, DVD players (progressive and interlaced), HDTV sources (1080i, 1035i, and 720p HDTV formats), TV and satellite tuners, camcorders, video games (progressive and interlaced), and laser disc players.
Video Device Standard Broadcast TV (not HDTV) via: cable, digital cable, satellite TV, DVD, or VCR Standard Video Camera Video Compatibility If Your Device Connector Is Attach to Adapter or Labeled Connector on Projector For Setup Instructions, see Comments NTSC, PAL, and SECAM formats Composite video or S-video Composite video or S-video Composite video connection on page 17. Not for progressive (i.e. HDTV) sources. See page 10.
Video Device Video Compatibility If Your Device Connector Is Attach to Adapter or Labeled Connector on Projector For Setup Instructions, see Comments 1080i, 720p VGA Computer In VGA connection on page 18 Not for Component 480i.
Connecting a computer source connect computer cable Required computer connections Connect one end of the provided computer cable (see page 16 for connecting video devices) to the blue M1 Computer In connector on the projector. Connect the other ends (USB and VESA) to the USB and VGA ports on your computer.
Displaying a computer source image remove lens cap Remove the lens cap. Toggle the Power switch on the side of the projector to the On position. toggle Power switch The LED flashes green and the fans start to run. When the lamp comes on, the start up screen displays and the LED is steady green. It can take a minute for the image to achieve full brightness. ? No start up screen? Get help on page 21. Turn on your computer. turn on computer The computer’s image should appear on the projection screen.
Adjusting the image adjust height If necessary, adjust the height of the projector by pressing the release button to extend the foot. rotate leveling foot If necessary, rotate the leveling foot located at the rear of the projector. elevator foot Avoid placing your hands near the hot exhaust vent in front of the projector. Position the projector the desired distance from the screen at a 90 degree angle to the screen.
Using the projector with Windows 98 for the first time a The first time you connect a computer running Windows 98 to the projector, the computer recognizes the projector as “new hardware” and the Add New Hardware Wizard appears. Follow these instructions to use the Wizard to load the correct driver (which was installed with your Windows operating system). If you are running Windows 2000, Windows ME, or Windows XP, skip these steps and go to “Adjusting the image” on page 13.
Skip this page if you did not connect a USB mouse cable For Windows 98: • If you connected the USB cable, the Add New Hardware Wizard appears again. Drivers must be installed to use the USB functionality. • The Wizard launches three times. The first time it detects a USB Composite Device. The second time a USB Human Interface Device (for the keyboard). The third time it detects a USB Human Interface Device (for the mouse).
Connecting a video device 4:3 screen You can connect video devices such as VCRs, DVD players, camcorders, digital cameras, video game consoles, HDTV receivers, and TV tuners to the projector. There is also an audio input via the red and white A/V connectors. You can connect the audio directly to the projector to get sound from the built-in speaker, or you can bypass the projector’s audio system and connect the audio directly from your source to a stereo or home theater system.
Video device connections Composite video connection Plug the provided A/V cable’s yellow connector into the video-out connector on the video device. Plug the other yellow connector into the yellow Video 2 connector on the projector. connect A/V cable Plug a white connector into the left audio out connector on the video device and plug a red connector into the right audio out connector on the video device.
VGA connection If your video device has a 15-pin VGA output, plug one end of the included computer cable into the VGA connector on your video source. This connector may be labeled “To Monitor” on the video source. Plug the M1 computer end of the cable into the Computer In connector on the projector. Do not plug the USB end of this cable into the video device.
Displaying video remove lens cap Remove the lens cap. Toggle the Power switch on the side of the projector to the On position. toggle Power switch The LED flashes green and the fans start to run. When the lamp comes on, the start-up screen is displayed and the LED is steady green. It can take a minute for the image to achieve full brightness. ? No start up screen? Get help on page 22. Plug in and turn on your video device.
Adjust the zoom and focus. adjust zoom and focus focus (thin ring) If the image is not square, adjust the keystone using the buttons on the keypad. If the image is not square, first make sure that the projector is perpendicular to the screen. If the image is larger or smaller on the top or bottom edge of the screen, press the top Keystone button to reduce the upper part of the image, and press the bottom Keystone button to reduce the lower part.
Shutting down the projector Troubleshooting your setup The projector automatically displays a black screen after no active source is detected for 30 minutes. This black screen helps preserve the life of the projector. The image returns when an active source is detected or a remote or keypad button is pressed. If your image appears correctly on the screen, skip to the next section. If it does not, troubleshoot the setup.
Problem Solution Result no start up screen plug power cord in projector’s left side remove lens cap toggle power switch correct image toggle power switch on side press the Computer button activate laptop’s external port only start up screen appears A Startu p Scree n Start u Scre p en computer image projected A restart laptop 22 A
no computer image, just the words “Signal out of range” A press the Auto Image button on keypad computer image projected adjust computer refresh rate in Control Panel>Display>Settings>Advanced>Adapter (location varies by operating system) Signa l rang out of e A A you may also need to set a different resolution on your computer, as shown in the following problem, “image fuzzy or cropped” Only my laptop’s background appears, not the Desktop icons A Disable “Extend my Windows Desktop” in Control Panel
Problem Solution Result image fuzzy or cropped set your computer’s display resolution to the native resolution of the projector (Start>Settings>Control Panel>Display>Settings tab) select 1024x768 image clear and not cropped A A A For a laptop, disable laptop monitor or turn-on dualdisplay mode move projector, adjust zoom, adjust height image not centered on screen correct image adjust horizontal or vertical position in Picture>Advanced menu 24
Problem Solution Result image not square adjust Keystone on keypad square image image not sharp adjust Sharpness (video sources only) in the Picture>Advanced menu correct image AB AB image does not fit 4:3 or 16:9 screen change aspect ratio to 4:3 or 16:9 in Picture>Aspect ratio menu 25 correct image
Problem Solution Result image upside down turn off ceiling in Settings>System menu correct image AB AB image reversed left to right turn off rear in Settings>System menu correct image A projected colors don’t match source AB adjust color, tint, color temperature, brightness, contrast in the menus COLOR correct image COLOR 26
Problem Solution Result The video embedded in my PowerPoint presentation does not play on the screen turn off the internal LCD display on your laptop Embedded video plays correctly A B A lamp won’t turn on, LED blinking red A B make sure vents aren’t blocked, turn off the projector and allow it to cool for one minute LED A B lamp turns on Start u Scre p en 27 B
Problem Solution Result “Change lamp” message appears at startup or lamp won’t turn on lamp must be replaced (see page 41) lamp turns on Start u Scre p en LED replace lamp Still need assistance? If you need assistance, visit our website at www.infocus.com/service or call us. Check out our HOW TO section there for additional information on using this projector for home theater or gaming applications. See the inside of the back cover for support contact information.
Using the remote control previous button next button The remote uses two (2) provided AA batteries. They are easily installed by sliding the cover off the remote’s back, aligning the + and - ends of the batteries, sliding them into place, and then replacing the cover. Caution: When replacing the batteries, be aware that using batteries other than the type provided with the projector may risk severe damage to the remote.
Using the audio connect audio cable Using the projector’s speakers To use the projector’s speaker, connect your source to the Audio In connectors (L and/or R) on the projector’s composite connectors. To adjust the volume, press the Volume buttons on the keypad or remote. To mute the sound, press the Mute button on the remote. Troubleshooting Audio If you aren’t hearing the audio, check the following: • adjust volume Make sure the audio cable is connected.
Using the keypad buttons Most buttons are described in detail in other sections, but here is an overview of their functions: Menu–opens the on-screen menus (page 34). menu navigation buttons Select–confirms choices made in the menus (page 34). Up/Down arrows–navigates to and adjusts settings in the menus (page 34). Auto Image–resets the projector to the source. Presets–cycles through the available preset settings (page 36). Keystone–adjusts squareness of the image (page 13). Volume–adjusts sound (page 30).
Optimizing computer images Presentation features After your computer is connected properly and the computer’s image is on the screen, you can optimize the image using the onscreen menus. For general information on using the menus, see page 34. Several features are provided to make giving presentations easier. Here is an overview, details are found in the menu section. • The Effect button on the remote allows you to assign various features to the button.
Optimizing video images Customizing the projector After your video device is connected properly and the image is on the screen, you can optimize the image using the onscreen menus. For general information on using the menus, see page 34. You can customize the projector for your specific setup and needs. See page 38 to page 40 for details on these features. • For rear projection, turn rear mode on in the Settings>System menu.
Using the menus keypad navigation buttons Main menu To open the menus, press the Menu button on the keypad or remote. (The menus automatically close after 60 seconds if no buttons are pressed.) The Main menu appears. Use the arrow buttons to move up and down to highlight the desired submenu, then press the Select button.
Picture menu Picture menu To adjust the following settings, highlight the setting, press Select, use the up and down arrows to adjust the values, then press Select to confirm the changes. Keystone: adjusts the image vertically and makes a squarer image. You can also adjust keystone from the keypad. Contrast: controls the degree of difference between the lightest and darkest parts of the picture and changes the amount of black and white in the image.
Presets: Presets are provided that optimize the projector for displaying computer presentations, photographs, film images, and video images. Film input is material originally captured on a film camera, like a movie; video input is material originally captured on a video camera, like a TV show or sporting event. You can use the preset as a starting point, then further customize the settings for each source. The settings you customize are saved in the preset for each source.
Advanced menu Sharpness: (video sources only) changes the clarity of the edges of a video image. Select a sharpness setting. Advanced menu Color Space: This option applies to computer and component video sources. It allows you to select a color space that has been specifically tuned for the input signal. When Auto is selected, the projector automatically determines the standard.
Settings menu Settings menu Audio: allows adjustments to Volume of the internal speaker and allows a chime to play when starting the projector. Adjustments can also be made from the projector’s keypad and the remote. Audio Sources: Power-up Source determines which source the projector checks first for active video during power-up. When the Autosource feature is On, the projector automatically finds the active source, checking the selected Power-up Source first.
Startup Logo: allows you to display a blank screen instead of the default screen at startup, and when no source is detected. Startup Logo Blank Screen: determines what color is displayed when you press the Blank button on the remote. Blank Screen Effect Key: allows you to assign a different function to the Effect button on the remote, allowing you to quickly and easily use the effect. Highlight an effect and press Select to choose a different one. • Blank: displays an empty screen.
Language: allows you to select a language for the onscreen display. Language menu Service: To use these features, highlight them and press Select. Service menu Factory Reset: restores all settings to their default. Lamp Reset: resets the lamp hours used counter in the About menu to zero. Do this only after changing the lamp. Service Code: only used by authorized service personnel. About: provides information about the projector and the active source.
Maintenance Cleaning the Lens 1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth. • Avoid using an excessive amount of cleaner, and don’t apply the cleaner directly to the lens. Abrasive cleaners, solvents or other harsh chemicals might scratch the lens. 2 Lightly wipe the cleaning cloth over the lens in a circular motion. If you don’t intend to use the projector immediately, replace the lens cap.
4 Loosen the two captive screws that attach the lamp housing to the projector. lamp connector 5 Detach the lamp connector from the projector by depressing the locking lamp cable tab on the connector and lightly pulling it free. WARNING: To avoid burns, allow the projector to cool for at least 30 minutes before you replace the lamp. Do not drop the lamp housing or touch the glass bulb! The glass may shatter and cause injury. lamp housing Be extremely careful when removing the lamp housing.
Cleaning the Lamp Housing Screens In dirty or dusty environments, the two dust filter screens in the lamp housing can become clogged, causing high temperatures and premature lamp failure. Routine maintenance to remove dust from the screens lowers the lamp operating temperature and prolongs lamp life. To maximize lamp life you should clean the screen every 250 hours. lamp housing lamp 1 Remove the lamp housing.
Appendix Red LED Behavior and Projector Errors Projected Image Size If the projector is not functioning properly and the LED is blinking red, consult Table 3 to determine a possible cause. There are two-second pauses between the blinking cycles. Visit our website for more details on the red LED error codes. NOTE: Visit our website for an interactive image size calculator.
C cable box 16 Color 35 Color Control 37 Color Space 37 Color Temperature 37 compatibility IBM-compatible 5 Macintosh 5 video devices 5 Computer In connector 11 connecting video device 16 connector panel 6 connectors on projector 9, 10 contacting InFocus 28 Contrast 35 customer service contact information 28 customizing the projector 33 D Display Messages 38 Drivers USB 15 Windows 98 15 DVDs 35 E Effect button 32, 33 Effect Key 39 F Factory Reset 40 focus 13, 20 INDEX Numerics 16x9 vs 4x3 screen aspect 16
H HDTV 8, 35 Horizontal 37 I IBM-compatible computers 5 image size 7 image optimization 32 image size projected 44 K keypad buttons projector 31 keystone adjustment 13, 20 L Lamp Housing Screens cleaning 43 lamp replacement 41 Lamp Reset 40 Language 40 LED 21 blinking green 21 solid green 21 LED Behavior red 44 LED behavior 21 leveling foot 19 Low Power 38 M M1 to Component adapter 18 Macintosh computers compatibility 5 maintaining the projector 41 Menu button 34 menu usage 34 Monitor Out connector 11 Mute
troubleshooting problems 21 turning off 21 T Tint 35 Tracking 37 troubleshooting 21 turning off projector 21 TV tuner 16 U USB, connecting 11 V Vertical 37 video optimizing 33 Video Standard 37 volume adjustment 20 Volume button 30 W warranty 28 Windows 2000 15 Windows 98 14 Windows ME 15 Windows XP 15 Z zoom 13, 20 R Rear 38 Red LED behavior 44 registering your projector 5 remote control advancing slides 11, 29 Effect key 29 laser pointer 29 Previous/Next buttons 29 usage 29 replacing the lamp 41 S Scree
Limited Warranty • Subject to the Limitations, Exclusions and Disclaimers hereof, InFocus Corporation (“InFocus”) warrants that the Projector, Lamps and Accessories (hereinafter collectively or individually referred to as “Product” as appropriate) purchased from InFocus, an InFocus distributor, or an InFocus reseller will conform to InFocus’ specifications and be free from defects in material or workmanship for the respective Limited Warranty period provided below.
The Warranty does not apply to cartons, carrying cases, shipping cases, external cabinets, accessories used in connection with the product, or cosmetic parts, knobs, or batteries. The Warranty period for LCD engines is either 2 years from the date of purchase of the projector or 2500 hours of projector usage, whichever comes first.
LIMITATION OF LIABILITY InFocus or the service facility authorized by InFocus will return the repaired/replaced Product freight prepaid to the purchaser. IT IS UNDERSTOOD AND AGREED THAT INFOCUS’ LIABILITY SHALL NOT EXCEED THE RETURN OF THE AMOUNT OF THE PURCHASE PRICE PAID BY PURCHASER Where applicable national law prohibits the exclusion or limitation of liability, InFocus excludes or limits its liability to the maximum extent permitted by national law.
