Cut Sheet

ManualsBrandsAppleton ManualsPin & Sleeve ReceptaclesAPP 20A 2W3P RECEPT EXPL

Table Of Contents

Class I, Division 1 and 2, Groups C, D

Does not intermate with

CPS 20 Amp Factory Sealed Pin

and Sleeve Receptacles

Covers are UL Classified to mount on Crouse-Hinds EDS mounting bodies. Crouse-Hinds and ENP are registered trademarks of Cooper Crouse-Hinds.

Plugs and Receptacles

Plugs and RecePtacles: HazaRdOus lOcatiOn

Visit our website at www.appletonelec.com or contact us at (800) 621-1506.

856

Contender

CPS Factory Sealed 20 Amp Pin and Sleeve Receptacles

Explosionproof, Delayed Action

Applications

• Locations where receptacles are used with stationary or

portable electrically operated devices such as:

— Lighting systems

— Conveyors

— Heaters

— Motor-generator sets

— Air conditioners

— Compressors

— Pumps

• Locations where damp or corrosive conditions exist.

• Meets all UL and CSA requirements for ground fault protection

in hazardous locations when GFCI cover is used.

Features

• Covers are UL Listed when used with Contender® Series

mounting bodies.

• Plug mechanical cable clamps prevent strain on cables – they

meet or exceed UL strain relief pull-out requirements.

• Insulators provide superior dielectric and mechanical strength

and lowest arc tracking.

• Delayed action construction: insert plug partially rotate slide on

front of receptacle and insert plug fully.

• Factory sealed: external seals not required.

• Plug and receptacles are supplied with pressure terminal

connectors.

Standard Materials

• Cover: copperfree (4/10 of 1% max.) aluminum

• Mounting bodies: malleable iron

• Screws: captive hex head slotted, stainless steel

• Insulating blocks: berglass reinforced thermoset polyester

• Plug grommet: neoprene

Standard Finishes

• Malleable iron mounting bodies: triple-coat– (1) zinc

electroplate, (2) chromate and (3) epoxy powder coat

• Covers and aluminum mounting bodies: epoxy powder coat

Options

• Copperfree (4/10 of 1% max.) aluminum receptacle cover and

box. Add sufx –SA.

• U-Line Corrosion Resistance kit. Order ULINE3RXKIT.

Certifications and Compliances

• UL Standard: UL 1010 (UL 1203), UL 894

• UL Listed: E10784

Summary of content (4 pages)

PAGE 1
Contender® CPS Factory Sealed 20 Amp Pin and Sleeve Receptacles Explosionproof, Delayed Action Class I, Division 1 and 2, Groups C, D Does not intermate with CPS 20 Amp Factory Sealed Pin and Sleeve Receptacles Applications Plugs and Receptacles: Hazardous Location Plugs and Receptacles • Locations where receptacles are used with stationary or portable electrically operated devices such as: — Lighting systems — Conveyors — Heaters — Motor-generator sets — Air conditioners — Compressors — Pumps • Lo
PAGE 2
Contender® CPS Factory Sealed 20 Amp Pin and Sleeve Receptacles Explosionproof, Delayed Action Does not intermate with CPS 20 Amp Factory Sealed Pin and Sleeve Receptacles Class I, Division 1 and 2, Groups C, D Catalog Numbers † 20 Amp 125-250 Vac 1HP, 20 Amp @ 18 Vdc Type Wire/Pole Hub Size (Inches) 1/2 CPS152-101 Dead-End 2W, 3P 3/4 CPS152-201 Single Gang Feed-Thru CPS152-301 CPS152-111 3/4 CPS152-211 1 CPS152-311 1/2 CPS152-102 3/4 CPS152-202 Plugs and Receptacles Dead-End 2W, 3P
PAGE 3
Contender® CPS Factory Sealed 20 Amp Pin and Sleeve Receptacles Explosionproof, Delayed Action Does not intermate with CPS 20 Amp Factory Sealed Pin and Sleeve Receptacles Class I, Division 1 and 2, Groups C, D Type Catalog Numbers † 20 Amp 125-250 Vac 1HP, 20 Amp @ 18 Vdc Wire/Pole Plugs and Receptacles: Hazardous Location Plugs and Receptacles Cover Assemblies CPS152R CPSCA Receptacle Only CPS152R GFCI Cover, 5 mA Trip Setting ‡ GFS1 Spring Cover Replacement Kit (Aluminum) CPSCA NEMA 3RX
PAGE 4
EDS Cast Device Mounting Boxes and Dimensions For Contender® CPS 20 Amp Factory Sealed Receptacles and CPP Plugs Dimensions in Inches/Millimeters B C Catalog Number Malleable Iron Aluminum Type Hub Size (Inches) 1/2 6.06/153.9 6.81/172.9 0.75/19.0 EDS171 EDS171-SA Dead-End 3/4 6.06/153.9 6.81/172.9 0.88/22.3 EDS271 EDS271-SA A Single Gang Feed-Thru Two Gang Feed-Thru Tandem † Feed-Thru 7.03/178.5 1.00/25.4 EDS371 EDS371-SA 6.06/153.9 6.81/172.9 0.75/19.