Cut Sheet
Table Of Contents
- Catalog Numbering Guide for EFDB/EFD
- EFDB/EFD and EDS Series Factory Sealed Control Stations
- Push Button Stations
- Push Button and Pilot Light Stations
- Stations with Rocker Arm Handle
- Dust Cap Push Button Stations
- Pilot Light Stations
- Selector Switches and Photocontrols
- Selector Switches and Cover Assemblies:
- Accessories and Parts
- NPBRKT Nameplate Mounting Bracket
- EFKB Covers with Pilot Lights, Push Buttons, or Photocontrol
- ESK/EFK Covers with Pilot Lights, Push Buttons, or Photocontrol
- Mounting Bodies
- Ordering Information
- Dimensions
Effective September, 2005
Copyright 2005
PAGE 22
800-621-1506
www.appletonelec.com
M- 22
M
Mounting Bodies for EFD and EDS
Control Stations
Furnished with Internal Ground Screw.
M- 2
Class I, Div. 1 and 2
Groups C,D
Class II, Div. 1 and 2
Groups E,F,G
Class III
NEMA 7CD,9EFG
Hub Size, Dead-End Catalog Numbers Feed-Thru Catalog Numbers
Inches Malleable Iron Aluminum Malleable Iron Aluminum
Single Gang, Two Gang, Tandem, and Three Device Bodies
Single Gang
1/2 EFD150-NL-Q EFD150A-NL-Q EFDC150-NL-Q EFDC150A-NL-Q
3/4 EFD175-NL-Q EFD175A-NL-Q EFDC175-NL-Q EFDC175A-NL-Q
1 EFD110-NL-Q EFD110A-NL-Q EFDC110-NL-Q EFDC110A-NL-Q
Two-Gang
1/2 EFD250-NL-Q EFD250A-NL-Q EFDC250-NL-Q EFDC250A-NL-Q
3/4 EFD275-NL-Q EFD275A-NL-Q EFDC275-NL-Q EFDC275A-NL-Q
1 EFD210-NL-Q EFD210A-NL-Q EFDC210-NL-Q EFDC210A-NL-Q
Tandem
†
1/2 EFDT50-NL-Q —— EFDCT50-NL-Q ——
3/4 EFDT75-NL-Q —— EFDCT75-NL-Q ——
1 EFDT10-NL-Q —— EFDCT10-NL-Q ——
Three Device
For use with EFKL Covers.
1/2 EFDL50-Q —— EFDCL50-Q ——
3/4 EFDL75-Q —— EFDCL75-Q ——
1 EFDL10-Q —— EFDCL10-Q ——
Blank Bodies for Brazed Hubs
Deep—malleable iron
Gang Cat. No.
1 Gang EFD-1-NL
2 Gang EFD-2-NL
3 Gang EFD-3-NL
4 Gang EFD-4-NL
5 Gang EFD-5-NL
Construct complete catalog number
per page M-23. Hubs will be located
in center of walls and evenly spaced
unless otherwise specified. Where
spacings are critical, submit sketch
showing spacing requirements.
Covers and Devices are listed on Pages M-12,15,20, and 21. Accessories on Pages M-16, 17, and 18. Dimensions on Pages M-24 and 25.
† For tandem bodies, external seals must be installed within 5 feet of each conduit entrance for Class I, Groups C and D.