Installation Manual

Place the mounting plate against the wall and
insert the toggle wings into the holes in the wall
to mount the plate.
NOTE: Before tightening toggle bolts and wood
screw, make sure the bottom of the mounting plate
touch the bottom of the cabinet when pushed
flush against the wall and that the plate is properly
centered under the cabinet.
CAUTION: Be careful to avoid pinching fingers
between the back of the mounting plate and the wall.
Tighten all bolts. Pull the plate away from the wall
to help tighten the bolts.
3
4
ATTACH THE MOUNTING
PLATE TO THE WALL
A1.
Attach the plate to the wall using toggle bolts.
At least one wood screw must be used to attach
the plate to a wall stud.
Remove the toggle wings from the bolts.
Insert the bolts into the mounting plate
through the holes designated to go into drywall
and reattach the toggle wings to
3
⁄4″ (19 mm) onto
each bolt.
1
INSTALLATION OVERVIEW
A1. Attach Mounting Plate to Wall
A2. Prepare Top Cabinet
Mount Microwave Oven
A5.
Adjust Exhaust Adaptor
A6.
Wall
Mounting
Plate
Spacing for Toggles
More Than Wall
Thickness
Bolt End
Toggle
Bolt
Toggle Wings
To use toggle bolts:
Installation Instructions
2
OUTSIDE TOP EXHAUST (Vertical Duct)
A
IMPORTANT NOTES:
• Make sure the screws for the
blower motor and blower plate
are securely tightened when
they are reinstalled. This will
help to prevent excessive
vibration.
• Make sure the motor wiring has
been properly routed and secured,
and that the wires are not pinched.
A7. Connect Ductwork
A3.
A4.
Check Damper Operation
Adapting Microwave Blower for
Outside Top Exhaust
12"
4"
NO
TE
: IT IS VERY
I
MPOR
TANT TO
READ AND FO
LLOWTHE DIRECTIONS
IN THE INSTALLATION INSTRU
CTI
ONS
BE
FO
RE PR
O
CEEDINGWITH TH
IS
REAR W
ALL TEMPLATE.
Thi
s
R
ea
rWall Templ
ate ser
ves to p
osition th
e botto
m
mounting platea
nd
to loc
ate th
e hor
izon
ta
l e
xhau
st
ou
t
let.
1. Us
e a l
ev
el
to
chec
k th
at the t
emplate is pos
itioned
accu
r
ately.
2. L
oc
ate a
ndmar
k at lea
st o
nestud on the left or
right
side of the centerli
ne.
016'
It is importa
nt to use at leas
t
one wo
od
sc
rew
mounted firmly
i
n a s
tud
to supp
ort the weight
of
the mic
r
owa
ve. M
ar
k two ad
dition
al, even
ly
spa
ced
locatio
ns f
o
r
the
supplied to
g
gle bol
t
s.
3. Dri
ll
h
ole
s in th
e marked locatio
ns.
Wher
e t
h
er
e is
a s
tud, dr
il
l
a 3/1
6"
hole for
wood scr
ews. F
or
holes
thatdo
n
o
t lin
e upwith
a
stud, d
r
ill 5
/8" holes fo
r
togg
le bolts
.
016'
DO
NOT
INSTALL
T
HE MO
U
NTI
NG P
L
ATE
AT THISTIME.
4. Re
move th
e te
mplate fr
o
m
the rea
r
wall.
5.Review
the In
s
ta
ll
a
tionInst
r
uc
tion book
for y
ou
r
installa
tion situat
i
on
.
Locate and mark holes
to ali
gn with holes in t
he
mounting
plate.
IMP
O
RTANT
:
LOCATE
AT LEAST ONE STUD
ON EI
THERSIDE OF
THE CENTE
RLINE.
MARKT
HE LO
CATIONF
O
R 2 ADDITIONAL, EVENLY
SP
ACE
D T
OGGLE
BOLTS IN THE MOUN
TING
PLATE
AREA.
Trim the re
ar wall tem
plat
e along
the do
tted line.
Da
rle
vu
elt
a
a
la
ho
ja
pa
ra
co
ns
ul
tarla
ver
sión
en
Espa
ñol.
Locate and mark
holes to ali
gn with holes in t
he
mountingplate.
IMPORTANT:
LOC
A
TE AT LEAST ONESTUD ON EITHER SI
D
E OF
THE
CENT
E
R
LI
N
E
.
MARKTHE LO
CATION
FOR 2 ADDITIONA
L, EV
ENL
Y
SPACEDTOGGLE BOLTS IN THE MO
UNTING PLATE
AREA.
Trim the rear wall templat
e along
the dotted line.
3/8"TO
EDG
E
EN-12