Installation Manual
EN-25
Installation Instructions
Operational check
1. Make sure the unit has been installed according to these instructions.
2. Remove all packing materials from the oven.
3. Replace house fuse or turn circuit breaker back on.
4. Plug power cord into receptacle .
5. Read operating instructions before testing the product.
6. Turn on the exhaust fan at Turbo speed and confirm it is operating by using a tissue (it will stick to the filter).
7. Confirm the outdoor exhaust flapper has opened.
8. Set the microwave oven for 1 minute and confirm the oven is operating normally using a cup of water.
9. Keep these installation instruction for the local electrical inspector’ s use.
3/8" TO EDGE
NOTE: IT IS VERY IMPORTANT TO
READ AND FOLLOW THE DIRECTIONS
IN THE INSTALLATION INSTRUCTIONS
BEFORE PROCEEDING WITH THIS
REAR WALL TEMPLATE.
This Rear Wall Template serves to position the bottom
mounting plate and to locate the horizontal exhaust
outlet.
1. Use a level to check that the template is positioned
accurately.
2. Locate and mark at least one stud on the left or
right side of the centerline.
It is important to use at least one wood
screw mounted firmly in a stud to support the weight
of the microwave. Mark two additional, evenly spaced
locations for the supplied toggle bolts.
3. Drill holes in the marked locations. Where there is
a stud, drill a 3/16" hole for wood screws. For holes
that do not line up with a stud, drill 5/8" holes for
toggle bolts.
DO NOT INSTALL THE MOUNTING PLATE
AT THIS TIME.
4. Remove the template from the rear wall.
5. Review the Installation Instruction book for your
installation situation.
Locate and mark holes to align with holes in the
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
Locate and mark holes to align with holes in the
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
Trim the rear wall template along the dotted line.
Trim the rear wall template along the dotted line.
12"
4"
Part No.:77222
316902478
R
etournez pour le Français
PN:16170000A73719
316902475
3/8" TO EDGE
NIRBOEN TAETE:D H IEANT IDIS
FNOSTLLOVEALLARYW T TIIHME
PDIORRTNECTATI TOONS
REAFRORE PREOCEDINGO WN
INSTRUCTION
This R
WALL TEMPLATE.ITH THISS
ear Wall
mountinTemlpat
o1 .u t l Useate.c gca u lrpleavteel atnod cthoe lec ko sceartev tes hte
o hpoorisitzoiontna lt heexh baouttsot m
2. Locaately. that the temp
ri
gth
et
I saidnde m aorf k tahte lceeanstte one stud laotn et
his positioned
socfr etw mot unitsed ifmiprmorltant to rulisene a.t le left or
l3o. cDathreio mnsic rfoorw atveh.e syMa rink atw ost auddd itito
osueapspt orton et hweoo wed ig
ila stlu holes in tuhpep limed toggle nbaoll,t evenly spahcetd
that d, drill a 3/1arked locationss.
d6". Wh
to
g
g
leo bnooltt ls. ine up wihthole a sfotru dw, ododr
screerew st. heFroer ish o
THIS DTOI NOT INSTALL THEill 5/8" holes lfeors
Remove ME. MOUNTING PLATE
A45.T. Review tthhe template from
installate iIonns tsialltautatiioonn .I tnhset rruecatrio
nwa lblo.ok
for your
ILomMcLOountatPOCAinRTe angTE plAN AT: d ma
LETtarekAS. holes to align with holes in the
TMSHAPERK CA CEENDTH TTEE LORLICANTE.IT
OONN FOE STR 2UD A ON EITHER SIDE OF
AREA.OGGLEO BLTS IN THDDE ITMOIONUTNAINL, G
EPLVEANTELY
LocIMmouLOatPOntCATRe aing TE AplANnd mT: a LTaErte.Ak h
oles to align with holes in the
TMAHSPRE ACCK TEENDH TTE ERLOILCNESATT. IO
ONNE F SOTR 2 UD ON EITHER SIDE OF
AREA.OGGLE BOLTS IN THADDEI MOTIOUNNTAL,
INGEV PLAENETLY
Trim the rear wall template along the dotted line.
Trim the rear wall template along the dotted line.
12"
4"
Dvaerrlsei óvnu eeltn a Eas lpaañ holoj.a para
consultar la
3/8" TO EDGE
NIRNOBEEATE T:FODHA RNE IND IT IS
V FOSTLALLLEROATWITHY IM OEPO
DRIRTAECNTTI TONOS
REAR WEA PRCOEEDINGWN
INSTRUCTION
This Rea
LL TEMPALTE .ITH THISS
mounr Wall Tem
ting pplate
o1 .u2 t l Uetsacce. au rllaevtateeell y .atnod cthoe lock c staetrhavete
ts htoe hporiosziotnitona lt heex hbaoutstto m
. Locate an the templ
ri
g
ht
I t siidds e maorfk tahte lceeanstt eorlne stud oant te
ihes positioned
sofcr tehwe momunted ifimrpormtlya nit to usei naet. le left or
l3o.c aDtriiolnlis crfoorw avteh.e sMaurkppln t aw os tauddd
ittoio snuapspt oortn teh ewo owd e
a st uhdo,l eds in the imeardk toggle boall,t sevenly spiagc het d
that do nrill a 3/16" hed locations. . W
to
g
gl
DeO NboOltt s.li ne up witohl ea fsortu d,wo dodr ilsclh
erreew st.h eFroer ihso l
o
THIS TIMET. INSTALL THE MOU5/8" holes foesr
Remove the tNTING PLATE
A4 5..T Review the Inemplate from
installations tsailtluaattiionon .I nthster ruecatri owna
llbo. o
Darle
k for your
LIomoMLOcTHauCPOtnteAT RinE aTgnAA pdTNla LT
mat:er.kEAST hoOles to align with holes in the
SPMARE ACCEK THENDTT EE LORLOGICNATE. IONN
FE SORTU 2 D ADON EITHER SIDE OF
AREA.GLE LBTOS IN THDE MOITIUONAINNL,TG PL
EVENATLY
E
LoLmoIMcTHOPautOCnteAR inET aTANgn pdAT LlT: at
maEAerk. S hTOoles to align with holes in the
MSPAREA KCCEED THNE L TOTEROGLCINEATIO.
NNE FOSRTU 2 DOAD NEITHER SIDE OF
AREA.GLE BOLTS IN THE DMOITIOUNNALT,I NPGL
EVENATELY
Trim the rear wall template along the dotted line.
Trim the rear wall template along the dotted line.
12"
4"
versióvun eeltn a Eas plaa ñhoojl.a para
consultar la
PN:16170000A76771