User Manual

ManualsBrandsAPS ManualsBack UPSAPS BX Series 750VA Back UPS

Table Of Contents

User Manual Back-UPS

BX Series 750VA, 1200VA, 1600VA, 2000VA

IMPORTANT SAFETY INSTRUCTIONS

Read the instructions carefully and look at the equipment to become familiar with the device before

trying to install, operate, service or maintain it. The following special messages may appear throughout

this document or on the equipment to warn of potential hazards or to call attention to information that

claries or simplies a procedure.

The addition of this symbol to either a “Danger” or “Warning” safety label indicates that

an electrical hazard exists which will result in personal injury if the instructions are not

followed.

This is the safety alert symbol. It is used to alert you to potential personal injury hazards.

Obey all safety messages that follow this symbol to avoid possible injury or death.

DANGER indicates a hazardous situation which, if not avoided, will result in death or

serious injury.

WARNING indicates a hazardous situation which, if not avoided, could result in death or

serious injury.

CAUTION indicates a hazardous situation which, if not avoided, could result in minor or

moderate injury.

NOTICE is used to address practices not related to physical injury.

Product Handling Guidelines

DANGER

WARNING

CAUTION

NOTICE

< 18 kg

< 40 lb

18-32 kg

40-70 lb

32-55 kg

70-120 lb

> 55 kg

> 120 lb

Summary of content (8 pages)

PAGE 1
User Manual Back-UPS BX Series 750VA, 1200VA, 1600VA, 2000VA IMPORTANT SAFETY INSTRUCTIONS Read the instructions carefully and look at the equipment to become familiar with the device before trying to install, operate, service or maintain it. The following special messages may appear throughout this document or on the equipment to warn of potential hazards or to call attention to information that claries or simplies a procedure.
PAGE 2
Safety and General Information SAVE THESE INSTRUCTIONS – This manual contains important instructions that should be followed during installation and maintenance of the UPS and batteries. Inspect the package contents upon receipt. Notify the carrier and dealer if there is any damages.  This UPS is intended for indoor use only.  Mains socket outlet that supplies the UPS shall be installed near the UPS and shall be easily accessible.  UPS must be connected to an earthed mains socket outlet.
PAGE 3
Place and Power On (cont.) 2. Connect the battery by pulling the battery handle up, and then pushing it into the unit. 3. Connect equipment to the UPS. Avoid using extension cords. 4. Plug the Back-UPS power cord directly into a wall outlet, not into a surge protector or power strip. 5. Press the POWER button for 1 second to turn on the UPS. After a long beep, the green indicator is on to confirm that the Back-UPS is ready to provide protection. Press the button for 2 seconds to turn off the UPS. 6.
PAGE 4
Battery Replacement CAUTION RISK OF HYDROGEN SULPHIDE GAS AND EXCESSIVE SMOKE Replace the battery at least every 5 years or at the end of its service life, whichever is earlier. Replace the battery immediately when the UPS indicates battery replacement is necessary. Replace batteries with the same number and type of batteries as originally installed in the equipment.
PAGE 5
Specifications Model Input BX750M-LM BX1200M-LM BX1600M-LM BX2000M-LM 120 Vac Voltage 50 Hz or 60 Hz (auto-sensing) Frequency Brownout Transfer 89 Vac, typical 145 Vac, typical Over-voltage Transfer Output UPS Capacity (total) 750VA/410W 1600VA/960W 1200VA/650W Voltage On Battery Frequency - On Battery 120 Vac ±10% 50 Hz / 60 Hz ± 0.5Hz Transfer Time 6ms typical, 10ms max.
PAGE 6
Status Indicators LED Audible Alarm On Off Constant Tone Constant beeping (every 1/2 second) Condition On-line - The Back-UPS is supplying AC power to the connected equipment On Line Overload - The power being used by the connected equipment has exceeded the capacity of the unit. Disconnect some equipment. Over-temperature Detected - The unit is overheating and will operate in AVR mode for 1 minute. The Back-UPS will shut down if the temperature is not lowered.
PAGE 7
Troubleshooting Detected Problem and Possible Cause The Back-UPS will not turn on Solution The Back-UPS has not been turned on. The Back-UPS is not connected to AC power, there is no AC power available at the wall outlet, or the AC power is experiencing a brownout or over voltage condition. Press the ON/OFF button. Make sure the power cord is securely connected to the wall outlet, and that there is AC power available at the wall outlet. Where applicable, check that the wall outlet is switched on.
PAGE 8
Service If the unit requires service, do not return it to the dealer. Follow these steps: 1. Review the Troubleshooting section of the manual to eliminate common problems. 2. If the problem persists, contact Schneider Electric IT (SEIT) Customer Support through the APC by Schneider Electric website, www.apc.com. a. Note the model number and serial number and the date of purchase. The model and serial numbers are located on the rear panel of the unit. b.