Operator's Manual
Table Of Contents
- Introduction
- AM/FM Radios A
- General Operation - AM/FM Radios A
- External Audio Sources - AM/FM Radios A
- Radio Operation - AM/FM Radios A
- Media - AM/FM Radios A
- Bluetooth® - AM/FM Radios A
- DAB+ Radio (Global Including Europe) - AM/FM Radios A
- Troubleshooting - AM/FM Radios A
- Specifications - AM/FM Radios A
- AM/FM Radios B
- General Operation - AM/FM Radios B
- Controls and Instruments
- Intended Use
- Basic Setting for Radio Reception
- Turn Radio On/Off
- Adjusting Brightness of the Radio Illumination (ILLUM)
- Adjust Volume
- Muting the Radio (MUTE)
- Turn Confirmation Beep On/Off (BEEP)
- Adjust Maximum Volume at Power-On (ONVOL)
- Adjust Sound
- Adjust Left/Right Volume Distribution (BAL)
- Adjust Front/Rear Volume Distribution (FAD)
- Turn Loudness On/OFF (LD)
- Restore Sound Settings
- Set Clock
- Radio Operation - AM/FM Radios B
- Setting the Radio Receiver
- Station Name
- Start Radio Mode
- Turn RDS Functions On/Off
- Select Wave Band/Memory Level
- Tuning in to a Station
- Sensitivity of Seek Function
- Store Station
- Select Stored Stations
- Scan Stored Stations (PRSTSCAN)
- Scan Wave Band for Available Stations (BANDSCAN)
- Program Type (PTY)
- Treble Reduction During Interference (HCUT)
- Set Key Function (KEY PRG)
- Traffic Information (Europe only) - AM/FM Radios B
- External Audio Sources - AM/FM Radios B
- MP3 Operation - AM/FM Radios B
- Bluetooth® Operation - AM/FM Radios B
- SiriusXM® Satellite Reception (for North America only) - AM/FM Radios B
- SiriusXM® Radio, General Information
- Display SiriusXM® Serial Number
- SiriusXM® Radio Mode
- Start SiriusXM® Radio Mode
- Select SiriusXM® Band (Memory Level)
- Select SiriusXM® Channels
- Store SiriusXM® Channels
- Select Stored SiriusXM® Channels
- SiriusXM® Channel Category Mode On/Off (CAT)
- Select SiriusXM® Channel Category
- Set Key Function (KEY PRG)
- System Information
- Specifications - AM/FM Radios B
- Touch Screen Radio
- General Operation – Touch Screen Radio
- External Audio Sources – Touch Screen Radio
- Radio Operation – Touch Screen Radio
- FM and AM Pages (North America)
- FM and AM Pages (Global Including Europe)
- FM and AM Pages (Japan)
- Presets
- FM Settings (Global Including Europe)
- SiriusXM® - General Information (United States-Puerto Rico-Canada)
- SiriusXM® Page (United States-Puerto Rico-Canada)
- SiriusXM® Browse (United States-Puerto Rico-Canada)
- SiriusXM® Browse - Tune Mix (United States-Puerto Rico-Canada)
- SiriusXM® Browse - Game Zone (United States-Puerto Rico-Canada)
- SiriusXM® Replay (United States-Puerto Rico-Canada)
- Digital Audio Broadcasting (DAB+) Page (Global Including Europe)
- Digital Audio Broadcasting (DAB+) Settings (Global Including Europe)
- Media – Touch Screen Radio
- Phone – Touch Screen Radio
- Camera (If Equipped) – Touch Screen Radio
- SiriusXM® Weather (United States-Puerto Rico-Canada) – Touch Screen Radio
- Apple CarPlay® – Touch Screen Radio
- Settings-General – Touch Screen Radio
- Settings-Sound – Touch Screen Radio
- Settings-Phone – Touch Screen Radio
- Dealer (Advanced) Settings – Touch Screen Radio
- Factory (Advanced) Settings – Touch Screen Radio
- Troubleshooting – Touch Screen Radio
- Specifications – Touch Screen Radio
- Specifications
- Product and SiriusXM® Identification Numbers
- Advisory Messages
- Federal Communications Commission (FCC) Declaration
- Federal Communications Commission (FCC) Warning
- Mexico Bluetooth® Information
- Paraguay Bluetooth® Information
- Brazil Bluetooth® Information
- Argentina Bluetooth® Information
- South Africa Bluetooth® Information
- Declaration of Conformity
- Eurasian Economic Union
1.Press the AUD key to open the menu for the sound
settings.
2.Press the AUD key several times until RESET N is
displayed.
3.Turn the volume control clockwise to select RESET
Y. After approx. 2 seconds all sound settings are
reset.
4.Press the AUD key several times to exit the menu.
NOTE: Press and hold the AUD key for more than 2
seconds to reset the audio settings only for the
audio source currently used.
KD34109,000078B-19-17JUL19
Set Clock
Synchronize Time (Vehicles with CommandCenter™
Only)
If clock is available on the vehicle CAN network, the
radio synchronizes the clock.
1.Turn key switch to IGN.
2.Turn on radio.
3.TIMESET displays.
4.After two seconds, clock displays.
5.Press SRC button to conrm time.
Set Time Manually
If there is no clock available on the vehicle CAN
network, the time can be modied through the radio
user menu. After power is disconnected (example:
battery or radio), reset clock using this procedure.
1.Through the radio user menu – press MENU button
until TIMESET displays.
2.TIMESET displays for 2 seconds.
3.Time displays with hour digits ashing.
4.Change value using volume knob.
5.Press left/right rocker button to move cursor to the
minute digits. If time format is 12H, radio changes
AM/PM automatically.
6.When time is correct, press SRC button to save and
return to normal radio functions.
Set Time Format
The radio can display the clock time in 12H or 24H
format.
1.Press MENU button until MODE 12H or 24H is
displayed.
2.Use volume knob to toggle between 12H and 24H
time format.
3.Stay on desired setting for 2 seconds to save.
Set Clock Mode
The radio can display the clock time by default
(ALWAYS) or on request (TEMP).
● ALWAYS – The time displays on the radio faceplate
unless a change in radio information is detected.
Radio information displays on change for 5 seconds.
Changes that prompt the radio information to display
include, source change, channel change, volume
change, preset change, and so on.
● TEMP – The time displays when requested by the
operator. Press and hold the MENU button for 3
seconds. Time displays for 5 seconds then reverts to
displaying radio information.
1.Press the MENU button until CLKMODE displays.
2.CLKMODE displays for 2 seconds.
3.ALWAYS or TEMP displays.
4.Use the volume knob to switch between ALWAYS
and TEMP clock mode.
5.Stay on desired setting for 2 seconds to save.
KD34109,0000037-19-17JUL19
General Operation - AM/FM Radios B
50-4