α711P RFID UHF Reader User Guide Ver. 0.
Copyright Copyright 2020. Aplusetechnology Co.,Ltd. All rights reserved. Apulsetech is the manufacturer of Apulsetech RFID handheld computers. This document and related software in this device are protected by international copyright laws. Any part of this document may not be reproduced, removed or used in any form by any means, without permission in writing from Apulsetech. The contents in this manual is subject to change without prior notice.
http://www.apulsetech.com Revision History Change Date Description Ver.0.
Table of Contents Copyright Revision History 1. About this guide ................................................................................................. 8 1.1 Introduction ...........................................................................................................................8 1.2 Configuration .........................................................................................................................8 1.3 Related document and Software ............................
4. Android Connections ........................................................................................ 17 4.1 Compatible Product Models ................................................................................................17 4.2 Demo Apps ...........................................................................................................................17 4.3 BT Connection ................................................오류! 책갈피가 정의되어 있지 않습니다. 4.3.1 Setup .........................
7.2 BT Mode ................................................................................................................................22 7.2.1 α711P BT Ready ...........................................................................................................22 7.2.2 α711P BT Connection ..................................................................................................22 7.2.3 α711P BT Sleep .....................................................................................
11. Troubleshooting ..............................................................................................
1. About this guide 1.1 Introduction The α711P (RFID UHF Reader) is a high performance UHF reader connecting to almost any mobile device. WIFI, Bluetooth or BT connections can be chosen in order to link to Android or iPhone device. Optional 2D barcode scanner engine from Zebra is available to capture 1D/2D barcode data and multitask on mobile phone efficiently. Users are able to experience highest working performance with α711P This guide is designed for helping users to operate α711P effectively.
Contact information is available at our website http://www.apulsetech.com When requesting support, please have following information; - Serial number of the device ( On manufacturing label ) - Firmware version 1.5 Safety information Symbols This guide uses the following symbols to indicate hazards and additional information. Symbol Name Description Warning Implies information that could result in serious injury to yourself or others.
▪ Do not take apart your α711P or accessories without authorizing. Only authorized institutions can repair this α711P. ▪ Please keep α711P away from magnetic equipment. The radiation of α711P will erase the information of the magnetic storage device. ▪ Please don’t use α711P under high temperature or in flammable areas (example: gas station). ▪ Please keep your α711P and accessories away from children without supervising.
2. Brief Description of α711P 2.1 α711P Overview 2.1.1 No. 1 Top view 1 Item 2D Imager 2.1.2 Description Scans barcodes by emitting a red laser when you press the related button. Bottom view 1 2 No. Item Description 1 BT connector Allows the device to be connected to PC or other device.
2.1.3 Front view 1 2 1 3 1 4 1 1. Description of LED Status No. 1 Item 25%, 50%, 75%, 100% Description All LED is green and does not blink - “25% LED” turns Red color when the battery is charging. Battery Level 2 BT When the BT mode is selected, Green lamp blinks 3 WIFI When the WIFI mode is selected, Blue lamp blinks 4 HID When the HID mode is selected, Green lamp. 5 READY In power saving mode, LED color is Green. 2. Flourish LAMA - Smartphone holder free stick 3.
2.1.4 Back view 1 2 1 3 4 5 No. Item Description Power key Press and hold to boot α711P when it’s completely turn off. When α711P is stuck and no physical buttons are not working, use small objects and press RESET button shortly, then device will force to shut down. Recommend not using the RESET key while α711P is working normally. It may damage the system and data loss.
DOWN 2 3 Volume DOWN or RFID power level DOWN button Default is volume DOWN Scanning Barcode Scan Trigger Hand Strap Place for attaching Hand Strap ( optional ) Holder 4 RFID Trigger RFID reader 5 Speaker For sound alert 3. Getting Started 3.1 Installing and Replacing the Battery α711P uses Lithium-ion rechargeable battery.
1. Turn the battery lock latch 45 degree to the left(Unlock side)and lift the battery cover. 2. Insert the battery into the battery slot, make sure the gold contacts are aligned. 3. Place the cover and turn the lock latch 45 degree to the right ( lock side ). Before removing the battery, turn off the power. Failure to do so it may cause damage to the device. When removing the battery cover, press the cover firmly and slide the latch unlock side, be careful not to damage your fingernail. 3.
3.4 Reset ⚫ Press reset button to reset the device. ⚫ Reset button is hardware key, it works while a711 powers on. It will shut down device and running application, you may lose data which made on the running application, please back-up important data frequently and use the reset function carefully.
4. Android Connections 4.1 Compatible Product Models It is recommended to use of the mobile device with Android OS version 5.0 or later. 4.2 Demo Apps - Installing Demo Apps. Install the application on the PC and Mobile device to connect to a711 and refer to Android SDK User Guide. α711P provides Demo Apps for function test and customer application development. Demo Apps may update or change without any notice. For latest demo apps or support, please contact your regional partner or visit our website.
1 2 Run Demo app on the mobile device. → 1. Select SPP mode from Bluetooth section. 2. Press Search button on the screen.
Select a searched device. → Control RFID or barcode scanner while BT in connected 4.4 Wi-Fi Connection 4.4.1 - Setup Select WIFI mode by pressing WIFI button on a711 and check if the WIFI LED is blinking. 4.4.
Run Demo app on the mobile device. Select a searched device. → → Press Search button on the screen.
5. iOS Connections Currently not available, coming soon. iOS Connection will be available by the end of 2020. It will be updated once it is ready.
6. LED Indications 6.1 α711P Booting & Battery Level status 6.2 BT Mode 6.2.1 α711P BT Ready BT mode standby : GREEN LED Blinks 6.2.2 α711P BT Connection BT mode Connection : GREEN LED ON 6.2.3 α711P BT Sleep ( Sleep when BT mode) : RED LED ON 6.2.4 α711P BT HID Ready ( BT mode standby ) : 6.2.
6.2.6 α711P BT HID Sleep ( BT HID mode Sleep ) 6.3 WIFI Mode 6.3.1 α711P WIFI Ready WIFI mode standby : GREEN LED Blinks 6.3.2 α711P WIFI Connection WIFI mode Connection : GREEN LED ON 6.3.3 α711P WIFI Sleep ( Sleep when WIFI mode) : RED LED ON 7. Follow Demo APK This chapter provides information to use α711P for the first time. For more specific information about settings of Demo apk and details, please refer to Android SDK User guide. 7.
⚫ Able to save read Tag information. ⚫ α711P will be into SLEEP mode after no Tag for a time as setting. Please contact with distributor or reseller you purchase if you have a problem on LED indicator. LED status should be checked by pressing power button if it is necessary. 7.2 Barcode Scanning ⚫ Button on the handle can be assign as Barcode Scanning button. ⚫ Able to save read Barcode information. ⚫ A711 will be into SLEEP mode after no Barcode scan for a time as setting.
8. OS & Firmware Update α711P is provided with most recently released firmware however if it’s necessary to update the OS, you can use OS update app tool which provided as default app. Backup all the data and information from your device before OS update. Your data, such as ringtones, texts, and voice messages, may be erased during the update. Check the battery fully charged or at least 90% charged before update, low battery may cause improper update or device malfunction. 8.
Power Supply Main Battery 6800 mAh (Rechargeable) Power Adapter 5V 2A Micro BT Adpater Network Characteristics WLAN IEEE 802.11 ac/a/b/g/n Bluetooth Bluetooth V4.
10. Troubleshooting Trouble shooting guide is available on saparated document, you can refer to FAQ or download document from our website, www.apulsetech.com 11. FCC Warning Statement FCC Part 15.19 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Part 15.
