LS 1/2 Product Manual English
Foreword Thank you for purchasing the Light Storm The Light storm LS 1/2 is made of 264 SMD lamp beads which are designed and manufactured carefully to have over 95 CRI value. Delicate design and elaborating production make a robust but exquisite housing, which can fulfill low forward heat of the fixture. LS 1/2 offers dual power solutions. You can use V-Mount or Anton Bauer battery in a location shooting. Besides, adapter attached is for your indoor shooting.
Item check list Before starting, please check that all the following items have been included with the Light Storm LS 1/2. If anything is missing, contact your dealer immediately. Light Controller Product manual Controller box Button battery AC/DC adapter Warranty Power cable Magic strip Tracing papers (10PCS) *The exceed is for clipping.
Nomenclature 1. Light LED beads Clamp handle Supporting Cable box Clip tube U-frame Cooling fins Hook 2. Controller box Antennas (*The signal strength is the best Eyelet bar when pulling the antennas as Socket the picture's show.) Power switch Display window Battery Mount Brightness wheel (*Anton Bauer or V-mount) DMX input/output DC power socket 3.
4. Display window Channels indicator Groups indicator DMX indicator Brightness percent indicator Channel setting button DMX model setting button DMX channel setting button(+) Group setting button DMX channel setting button(-) Installations 1. Install the hook 2. Install the light 1) Turn around the clamp handle to install the light on the tripod. 2) Set the light at a specific angle, and pull or turn around the tilt knob to fasten the light.
3. Insert the connect cable dot to dot to power the light . *Tie the connect cable around the hook 4. Power the controller box 1) Powered by the adapter Locking spring AC 100V-240V Locking slot * Please pull the power adapter out by pushing the locking spring down on the controller box.
2) Powered by the battery V-Mount Battery Anton Bauer Battery * Battery output current ≥ 4A; * Please choose the model of the Light Storm by your battery need. 5. Clip the tracing paper by the clamps Tracing paper Cable box of the Light 6. Insert the button battery to power the controller.
Operations 1. Press power switch to turn on the Light Storm. * “Channel 1 ,Group A” is by default. The brightness is 10% by default. 2. Manual controlled by the controller box Brightness adjustment and display 3. Remote controlled by the controller You can control the LS 1/2 of channel 2, group C according to the following directions.
*2) Group setting and display 2) The controller setting and display Press ( ) to set the channel 2 “ ” indicator lights The controller setting is finished. *The Light Storm has three channels (1/2/3) and four groups (A、B、C、D). 3) Brightness adjustment Press ( or ) of group C to adjust the brightness . The brightness varies in 1% at one press. Brightness changes between 10 and 100.
4.
2) The DMX setting *1) Press DMX model setting button on the controller box to enter into the DMX model. *2) Press the DMX channel setting button (+/-) on the controller box to your needed DMX channel. 3) The standard DMX console control Control the Light Storm by the standard console within the same DMX channel setting as above. * Channel 1 is by default when in DMX model，DMX channel is between 1 and 512. Tips and trouble setting Please turn off the Light Storm LS 1/2 before removing batteries.
Specifications Model LS 1/2w Operation Current 4A Power Supply DC 15V Power Input 60W Beam Angle 120° Color Temperature 5500K Average Life Span ≥100,000 hours Cooling Mode Natural convection heat transfer Radio Frequency 2.4GHz Channels 1/2/3 Groups A/B/C/D Remote Range Sizes (L*W*H) ≤100m Light 360.5*217.2*25.4 mm Controller box 238.0*118.7*48.1 mm (*vertical antennas included) (Anton Bauer Battery) Controller box (V-Mount) 238.0*118.7*59.
