Aqua Logic Programming Flow Chart Aqua Logic Automation and Chlorination denotes conditional items PS-4 only (actuators, cell & remote display not included - order separately) Installation Manual for models AQL-PS-4 AQL-PS-8 AQL-PS-16 PS-4 only G G LDLINE C ON TROLS North Kingstown, RI 02852 USA 092042H Copyright © 2008 Goldine Controls AQL-PS-8-V AQL-PS-16-V LDLINE C ON TROLS www.goldlinecontrols.
LIMITED WARRANTY Goldline warrants its Aqua Rite, Aqua Rite Pro, Aqua Trol, Aqua Logic and Pro Logic products (products with Goldline part numbers starting with AQ-RITE-, AQ-RT-PRO, AQ-TROL-, AQ-LOGIC-, AQL-P-, AQL-PS-, AQL-CL-, PL-P-, PL-PS-, and HPC-2) to be free from defects in material or workmanship, under normal use and service: IMPORTANT SAFETY INSTRUCTIONS When using this electrical equipment, basic safety precautions should always be followed, including the following: • READ AND FOLLOW ALL INSTRU
The following statement is applicable if any of the wireless accessories are connected to the Aqua Logic system. Table of Contents FCC Statement (Compliance Statement, Part 15.19): This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING (Part 15.
Introduction Before You Begin What’s Included Before attempting to install the Aqua Logic system, check that the following components have been included in the package: Aqua Logic Electronics Unit (3) Temperature sensors with 15 ft. (5m) cable, hose clamp Aqua Logic Expansion Unit (PS-16 only) What’s NOT Included Heater Checkout Follow these instructions to verify that the Aqua Logic is properly controlling the heater. 1.
Toggle between 7-day (default) and Weekend/Weekday time options + > Move to previous/next configuration menu > All Timeclocks 7-day This selection affects ALL of the timeclock logic in the Aqua Logic. If “7-day” is selected, each timeclock will have one set of turn-on/turn-off settings that operate every day of the week.
Select 6B Spa A 6B A, Button 1 Pool/Spa + Push to access the 6 Button Spa Side Remote options > Move to previous/next configuration menu Rotates between all available remotes + > Move to next menu item Rotates between System Off, Pool/Spa, Filter, Lights, Heater1, Valve3, Valve4, and all available Aux outputs > Move to previous/next menu item or next configuration menu + > Salt is required only if you are using the chlorinator features on the Aqua Logic Control.
Valve3 Function Manual On/Off (default) – the valve3 relay will alternate between turning on and off when the VALVE3 button is pressed. There is no automatic control logic. The VALVE3 button can also be used to turn the valve output on or off. Countdown Timer – the valve3 relay will turn on when the VALVE3 button is pressed and then will turn off automatically after a programmed time (see Timers Menu in the Operations Manual). The VALVE3 button can also be used to turn the output off.
AQL-PS-8-V models only: Aux3 - Aux7 only AQL-PS-16-V models only: Aux7 - Aux14 only Round Diameter x Diameter x Average Depth x 5.9 Diameter x Diameter x Average Depth x 785 Aux7 Function Group Oval Length x Width x Average Depth x 6.7 Length x Width x Average Depth x 893 Aux7 Group Timer: None(Manual) Aux7 Name Cleaner Aux7 Group Filter: Unaffected Type of Salt to Use It is important to use only sodium chloride (NaCl) salt that is greater than 99.0% pure.
Timeclock – the aux relay will turn-on and turn-off at the times set for the aux timeclock in the Timers Menu (see Operations Manual). The AUX button can also be used to turn the output on and off. Solar – the aux relay operates a solar booster pump which will turn on when the filter pump is running and solar heat is available and the water is less than the desired temperature setting. It is important to note that “Solar” must be enabled in the “Solar Config.” menu for proper operation to occur.
Aux1 Name Cleaner Aux1 Function Manual On/Off + Push to access Aux options > Move to previous/next configuration menu Rotates between all available names + > Move to next menu item Rotates between Manual On/Off (default), Countdown Timer, Low SpeedFilter, Timeclock, Solar, Low speed-Spa Filter, Group & Super Chlorinate + > Move to next menu item for manual on/off, countdown timer and timeclock functions Aux1 Relay Standard Toggle between Standard (default) and Dimmer + > > Move to next menu item
Lights Group The Lights Group function allows the user to perform multiple tasks with a single push of the “Lights” button. When setting up a Group function, refer to page 22 for specific programming information. There are two Group menus; the first menu determines how the group command will be initiated (Manual On/Off, Countdown Timer, or Timeclock) and the second menu selects the desired functions and their respective control parameters.
3. Plumbing “Standard” Pool/Spa system configuration These systems use a single filter pump and filter. Pool or spa operation is controlled by two 3-way valves (suction and return). Refer to the diagram below.
If solar is “Enabled”, the valve or solar pump relay will turn on when the water temperature is less than the desired temperature setting AND the solar sensor is hotter than the water by at least 8ºF. The desired temperature is in the “Settings Menu”. If applicable, the homeowner will be prompted to enter separate pool and spa desired temperature settings. Depending on the position of the pool/spa suction valve, the proper temperature setting will be used.
3. The solar sensor should be installed on the spa loop prior to the heater and will display the spa temperature whenever the “Spa Filter” pump is running. 4. Solar heater control is NOT available for dual equipment systems. 5. The Aqua Logic can be programmed to accommodate spillover if desired. Note that spillover operation will be automatically suspended whenever the spa filter pump is turned on. 6. The chlorinator cell must be installed in the pool plumbing.
Flow Monitor This feature will help protect the filter pump from damage due to no flow. When used with a Goldline flow switch, the Aqua Logic monitors the state of water flow when the filter pump is on. If no flow is detected for more than 15 minutes, the Aqua Logic will shut down the pool pump and the “Check System” LED will indicate an error. The error will be cleared the next time the pump is turned on.
4. Electrical Wiring For use with PS-16 only Control Power Input V1=Aux1, V2=Aux2 This menu appears only if the Pool/Spa Setup is “Pool Only” or “Spa Only”. When enabled, Valve 1 (return) will follow the Aux1 output and Valve 2 (suction) will follow the Aux2 output. When disabled (default), the return and suction pool/spa valves function normally.
Push to access Pool/Spa options > Move to previous/next configuration menu + Rotates between Pool and Spa-Std (default), Pool and Spa-Dual, Pool Only, and Spa Only options > Move to next menu item > Pool/Spa Setup Pool and Spa-Std + > Pool/Spa Config. + to view/change General Purpose Outlet If desired, a duplex receptacle with weatherproof cover (supplied by installer) may be installed in the knockouts on the lower right side of the Aqua Logic enclosure.
To access the Configuration Menus Configuration Menu-Unlocked Lo Speed Hi Speed Common Ground Menu Press repeatedly until “Configuration Menu” is displayed > Press BOTH buttons SIMULTANEOUSLY for 5 seconds to unlock > Configuration Menu-Locked > Two speed filter pump: Requires 2 relays (FILTER plus one of the AUX relays) for proper operation of both speeds. ! IMPORTANT: Be sure to follow the wiring diagram below AND to configure the control logic according to the instructions on page 25.
Note that all functions in the table may not be offered. The available functions are dependent on how the Aqua Logic is configured. For example, if the Aqua Logic is configured for a single heater, “Heater2” will not be available as an option in the Group menu. Also, under some circumstances, functions will be displayed but can’t be changed. Note that the function whose menu you are in, will not be displayed as an option and will automatically turn on when the group is activated.
5. Configuration Setup Hayward Heaters Refer to the instructions in the heater manual for “2-wire Remote Thermostat” operation under “Remote Control Connections” and the diagram on the below: 1. 2. 3. 4. 5. 6. Turn off power to heater. Wire Aqua Logic to terminals 1 & 2 (see diagram). Leave jumper attached to terminals 4 & 5. Move “BYPASS” dipswitch on heater circuit board to “ON” position (up). Turn heater power back on.
Raypak RP2100 Pool/Spa Heater Goldline Aqua Rite Chlorinator The Aqua Logic can control one or more Goldline Aqua Rite chlorinators when additional sanitizing capacity is required. A 4 wire connection is used to communicate to the Aqua Rite and can be wired up to 500' apart. Any outdoor rated 4 conductor cable can be used. Refer to the wiring diagrams below for proper wiring connection to the Aqua Rite. NOTE: There must be only 1 "primary" unit. All other Aqua Rite units must be configured as "secondary".
Temperature Sensors The Aqua Logic utilizes 10K ohm thermistor type sensors. Three sensors (water temperature, air temperature and solar temperature (spa temperature for “Pool and Spa-Dual”)) are included. If the Aqua Logic is being used to control a solar heating system, the solar sensor is required. The sensors are provided with a 15 ft. cable. If a longer cable is required, contact the Goldline service dept. (888-9217665) for information on suitable cable types and splices.
Temperature Sensors The Aqua Logic utilizes 10K ohm thermistor type sensors. Three sensors (water temperature, air temperature and solar temperature (spa temperature for “Pool and Spa-Dual”)) are included. If the Aqua Logic is being used to control a solar heating system, the solar sensor is required. The sensors are provided with a 15 ft. cable. If a longer cable is required, contact the Goldline service dept. (888-9217665) for information on suitable cable types and splices.
Raypak RP2100 Pool/Spa Heater Goldline Aqua Rite Chlorinator The Aqua Logic can control one or more Goldline Aqua Rite chlorinators when additional sanitizing capacity is required. A 4 wire connection is used to communicate to the Aqua Rite and can be wired up to 500' apart. Any outdoor rated 4 conductor cable can be used. Refer to the wiring diagrams below for proper wiring connection to the Aqua Rite. NOTE: There must be only 1 "primary" unit. All other Aqua Rite units must be configured as "secondary".
5. Configuration Setup Hayward Heaters Refer to the instructions in the heater manual for “2-wire Remote Thermostat” operation under “Remote Control Connections” and the diagram on the below: 1. 2. 3. 4. 5. 6. Turn off power to heater. Wire Aqua Logic to terminals 1 & 2 (see diagram). Leave jumper attached to terminals 4 & 5. Move “BYPASS” dipswitch on heater circuit board to “ON” position (up). Turn heater power back on.
Note that all functions in the table may not be offered. The available functions are dependent on how the Aqua Logic is configured. For example, if the Aqua Logic is configured for a single heater, “Heater2” will not be available as an option in the Group menu. Also, under some circumstances, functions will be displayed but can’t be changed. Note that the function whose menu you are in, will not be displayed as an option and will automatically turn on when the group is activated.
To access the Configuration Menus Configuration Menu-Unlocked Lo Speed Hi Speed Common Ground Menu Press repeatedly until “Configuration Menu” is displayed > Press BOTH buttons SIMULTANEOUSLY for 5 seconds to unlock > Configuration Menu-Locked > Two speed filter pump: Requires 2 relays (FILTER plus one of the AUX relays) for proper operation of both speeds. ! IMPORTANT: Be sure to follow the wiring diagram below AND to configure the control logic according to the instructions on page 25.
Push to access Pool/Spa options > Move to previous/next configuration menu + Rotates between Pool and Spa-Std (default), Pool and Spa-Dual, Pool Only, and Spa Only options > Move to next menu item > Pool/Spa Setup Pool and Spa-Std + > Pool/Spa Config. + to view/change General Purpose Outlet If desired, a duplex receptacle with weatherproof cover (supplied by installer) may be installed in the knockouts on the lower right side of the Aqua Logic enclosure.
4. Electrical Wiring For use with PS-16 only Control Power Input V1=Aux1, V2=Aux2 This menu appears only if the Pool/Spa Setup is “Pool Only” or “Spa Only”. When enabled, Valve 1 (return) will follow the Aux1 output and Valve 2 (suction) will follow the Aux2 output. When disabled (default), the return and suction pool/spa valves function normally.
Flow Monitor This feature will help protect the filter pump from damage due to no flow. When used with a Goldline flow switch, the Aqua Logic monitors the state of water flow when the filter pump is on. If no flow is detected for more than 15 minutes, the Aqua Logic will shut down the pool pump and the “Check System” LED will indicate an error. The error will be cleared the next time the pump is turned on.
3. The solar sensor should be installed on the spa loop prior to the heater and will display the spa temperature whenever the “Spa Filter” pump is running. 4. Solar heater control is NOT available for dual equipment systems. 5. The Aqua Logic can be programmed to accommodate spillover if desired. Note that spillover operation will be automatically suspended whenever the spa filter pump is turned on. 6. The chlorinator cell must be installed in the pool plumbing.
If solar is “Enabled”, the valve or solar pump relay will turn on when the water temperature is less than the desired temperature setting AND the solar sensor is hotter than the water by at least 8ºF. The desired temperature is in the “Settings Menu”. If applicable, the homeowner will be prompted to enter separate pool and spa desired temperature settings. Depending on the position of the pool/spa suction valve, the proper temperature setting will be used.
3. Plumbing “Standard” Pool/Spa system configuration These systems use a single filter pump and filter. Pool or spa operation is controlled by two 3-way valves (suction and return). Refer to the diagram below.
Lights Group The Lights Group function allows the user to perform multiple tasks with a single push of the “Lights” button. When setting up a Group function, refer to page 22 for specific programming information. There are two Group menus; the first menu determines how the group command will be initiated (Manual On/Off, Countdown Timer, or Timeclock) and the second menu selects the desired functions and their respective control parameters.
Aux1 Name Cleaner Aux1 Function Manual On/Off + Push to access Aux options > Move to previous/next configuration menu Rotates between all available names + > Move to next menu item Rotates between Manual On/Off (default), Countdown Timer, Low SpeedFilter, Timeclock, Solar, Low speed-Spa Filter, Group & Super Chlorinate + > Move to next menu item for manual on/off, countdown timer and timeclock functions Aux1 Relay Standard Toggle between Standard (default) and Dimmer + > > Move to next menu item
Timeclock – the aux relay will turn-on and turn-off at the times set for the aux timeclock in the Timers Menu (see Operations Manual). The AUX button can also be used to turn the output on and off. Solar – the aux relay operates a solar booster pump which will turn on when the filter pump is running and solar heat is available and the water is less than the desired temperature setting. It is important to note that “Solar” must be enabled in the “Solar Config.” menu for proper operation to occur.
AQL-PS-8-V models only: Aux3 - Aux7 only AQL-PS-16-V models only: Aux7 - Aux14 only Round Diameter x Diameter x Average Depth x 5.9 Diameter x Diameter x Average Depth x 785 Aux7 Function Group Oval Length x Width x Average Depth x 6.7 Length x Width x Average Depth x 893 Aux7 Group Timer: None(Manual) Aux7 Name Cleaner Aux7 Group Filter: Unaffected Type of Salt to Use It is important to use only sodium chloride (NaCl) salt that is greater than 99.0% pure.
Valve3 Function Manual On/Off (default) – the valve3 relay will alternate between turning on and off when the VALVE3 button is pressed. There is no automatic control logic. The VALVE3 button can also be used to turn the valve output on or off. Countdown Timer – the valve3 relay will turn on when the VALVE3 button is pressed and then will turn off automatically after a programmed time (see Timers Menu in the Operations Manual). The VALVE3 button can also be used to turn the output off.
Select 6B Spa A 6B A, Button 1 Pool/Spa + Push to access the 6 Button Spa Side Remote options > Move to previous/next configuration menu Rotates between all available remotes + > Move to next menu item Rotates between System Off, Pool/Spa, Filter, Lights, Heater1, Valve3, Valve4, and all available Aux outputs > Move to previous/next menu item or next configuration menu + > Salt is required only if you are using the chlorinator features on the Aqua Logic Control.
Toggle between 7-day (default) and Weekend/Weekday time options + > Move to previous/next configuration menu > All Timeclocks 7-day This selection affects ALL of the timeclock logic in the Aqua Logic. If “7-day” is selected, each timeclock will have one set of turn-on/turn-off settings that operate every day of the week.
Introduction Before You Begin What’s Included Before attempting to install the Aqua Logic system, check that the following components have been included in the package: Aqua Logic Electronics Unit (3) Temperature sensors with 15 ft. (5m) cable, hose clamp Aqua Logic Expansion Unit (PS-16 only) What’s NOT Included Heater Checkout Follow these instructions to verify that the Aqua Logic is properly controlling the heater. 1.
The following statement is applicable if any of the wireless accessories are connected to the Aqua Logic system. Table of Contents FCC Statement (Compliance Statement, Part 15.19): This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING (Part 15.
LIMITED WARRANTY Goldline warrants its Aqua Rite, Aqua Rite Pro, Aqua Trol, Aqua Logic and Pro Logic products (products with Goldline part numbers starting with AQ-RITE-, AQ-RT-PRO, AQ-TROL-, AQ-LOGIC-, AQL-P-, AQL-PS-, AQL-CL-, PL-P-, PL-PS-, and HPC-2) to be free from defects in material or workmanship, under normal use and service: IMPORTANT SAFETY INSTRUCTIONS When using this electrical equipment, basic safety precautions should always be followed, including the following: • READ AND FOLLOW ALL INSTRU
Aqua Logic Programming Flow Chart Aqua Logic Automation and Chlorination denotes conditional items PS-4 only (actuators, cell & remote display not included - order separately) Installation Manual for models AQL-PS-4 AQL-PS-8 AQL-PS-16 PS-4 only G G LDLINE C ON TROLS North Kingstown, RI 02852 USA 092042H Copyright © 2008 Goldine Controls AQL-PS-8-V AQL-PS-16-V LDLINE C ON TROLS www.goldlinecontrols.