Table Top Game User Manual
Wired Remote Controls
Up to 3 wired remote controls can be installed. See “Electrical Wiring” (page 19) for instructions on
running the cable from the Aqua Logic main unit to the remote control. Also refer to the remote’s installa-
tion instructions for more information.
AQL-WW-PS-x (x=4,8, or 16), AQL2-Wx-PS-x (x=4,8, or 16)
The AQL-WW-PS-x and AQL2-Wx-PS-x display/keypads must be mounted indoors or in a weather
protected area (rain should never hit the unit). Note that the number of outputs on the remote (“4”, “8” or
“16”) must match the outputs on the Aqua Logic main control unit. The display/keypad is designed to
mount onto a standard electrical utility box (same box as a triple light switch, ideal for new construction) or
can be mounted directly onto any wall surface. When selecting a location, note that the wire to the Aqua
Logic main unit must be less than 500’ long.
AQL-SS-6B-x, AQL-SS-D-x (x=W, G or B for White, Gray or Black)
The AQL-SS-6B and AQL-SS-D are double insulated, waterproof devices which are intended for instal-
lation at the water's edge. The remote controls come with an attached 150’ cable and are typically
installed at the tile-line of the spa wall, or in the deck, within arm's reach of a pool/spa occupant.
Wireless Remote Controls
A single Base Station must be installed on the Aqua Logic in order to use any of the Goldline wireless
remote controls. With the Base Station installed, there is no limit on the number of wireless remotes that
can used. The maximum distance between the wireless remotes and the base station on the Aqua Logic
main control unit is 400 feet (120m) line of sight or 200 feet (60m) through walls, etc. If in doubt about the
distance, test operation before installing the remote.
Use AQL-BASE-RF for all AQL wireless remote controls. Use AQL2-BASE-RF for all AQL2 wireless
remote controls.
All wireless models require the user to run the “Teach Wireless” routine in the Settings Menu. This infor-
mation can be found in the Aqua Logic Operation Manual and the owner’s manual of each remote.
AQL-WW-RF-PS-x, AQL-Wx-RF-PS-x (x=4,8, or 16)
The AQL-WW-RF-PS-x is a wall mounted display/keypad and must be mounted indoors or in a weather
protected area (rain should never hit the unit). Note that number of outputs on the remote (e.g. “4”, 8” or
“16”) must match the outputs on the Aqua Logic Control Center. Also note that the remote must be within
6 feet of a standard 120V wall outlet for the plug-in power supply included with the unit.
AQL-Tx-RF-PS-x, AQL2-Tx-RF-PS-x (x=4,8, or 16)
The AQL-Tx-RF-PS-x and AQL2-Tx-RF-PS-x are portable battery operated remote controls designed
to be used in a weather protected area (rain should never hit the unit). Both remotes come with a wall
mounted power supply for recharging the built-in batteries.
AQL-SS-RF, AQL2-SS-RF, AQL2-POD
The AQL-SS-RF, AQL2-SS-RF and AQL2-POD are waterproof portable remote controls that are
designed to be used in and around the pool/spa area. These units float and can be left in the pool/spa water
for easy access.
7 32
NOTE: The configuration parameters for all Aux outputs are same as shown below for Aux1. PS-4: Aux1 and Aux2.
PS-8: Aux1 through Aux6. PS-16: Aux1 through Aux14. Also note that for the PS-16, Valves7, 8, 9 and 10 are turned
On/Off with the control function selected for Aux7, 8, 9, and 10, respectively.
Aux1 Config.
+ to view/change
Aux1 Function
Manual On/Off
Aux1 Group
Filter: Unaffected
Aux1 Group
Timer: None(Manual)
Aux1 Name
Cleaner
Aux1 Relay
Standard
Push to access Aux options
Options available depend on the function that is selected
Rotates between Manual On/Off (default),Countdown Timer and Timeclock
Rotates between all available names
Toggle between Standard (default) and Dimmer
Move to previous/next configuration menu
Move to previous/next menu item or next configuration menu
Move to next configuration menu item
Move to next menu item
Move to next menu item or previous/next configuration menu
Aux1 Interlock
Disable
Aux1 Freeze
Disable
Toggle between Enabled and Disabled (default) Aux1 Interlock
Toggle between Enabled and Disabled Aux1 Freeze(default)
Move to next menu item
Move to previous/next configuration menu
+
+
+
+
+
+
+
+
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
for all functions except solar, dimmer relay,
low speed (filter pump), and group
for all functions except dimmer relay,
low speed, and group
for group function only
for group function only
for manual on/off, countdown
timer and timeclock functions
Rotates between
Manual On/Off (default), Countdown Timer, Low Speed-
Filter, Timeclock, Solar, Low speed-Spa Filter, Group & Super Chlorinate
Move to next menu item
!
WARNING: Do not use the Aqua Logic to control an automatic pool cover. Swim-
mers may become entrapped underneath the cover.
NOTE: If “Pool and Spa-Dual” is selected, Aux1 is dedicated to use as the spa filter. Its Name is set to Spa Filter, the
Function is set to Timeclock and Interlock is set to Disabled. These can’t be changed.
Aux1 Name
The Aqua Logic allows you to assign any one of a number of names (e.g. “Cleaner Pump,
Waterfall, Gazebo Light, etc.) to each of the aux outputs control function. This will make the
Aqua Logic much more user friendly to the homeowner when they want to turn various aux
equipment on or off or program the timeclocks. A sheet of small name labels is included with
the Aqua Logic main unit and each remote display/keypad so that the “Aux” pushbutton can
be labeled the same as the name that you have assigned. At this time it is also a good idea to
make sure that the relay in the control box is also labeled (hand written) with the same name
as a help to technicians who may service this system at a later date.
Aux1 Function
Manual On/Off (default)—the aux relay will alternate between turning on and off when the
aux button is pressed. There is no automatic control logic.
Countdown Timer – the aux relay will turn on when the AUX button is pressed and then will
turn off automatically after a programmed time (see Timers Menu in the Operations Manual).
The AUX button can also be used to turn the output off.
Low Speed of a 2-speed Filter Pump – the Aqua Logic will operate the aux relay whenever
the low speed operation of the filter pump is required. It is very important that the “2-speed”
filter pump option be selected under the “Filter Config.” Menu for proper operation.