DO NOT RETURN THIS PRODUCT TO RETAILER Return Merchandise Authorization Number (RMA#) is Required. To obtain RMA #, Technical Support or to review Troubleshooting Videos and Step-By-Step Troubleshooting Procedures please visit www.AquaProducts.com/Service. JET TECHNOLOGY OPERATOR MANUAL AND TROUBLESHOOTING GUIDE IMPORTANT SAFETY INSTRUCTIONS Read and Follow All Instructions Before Using Your Pool Cleaner This manual is for use with a variety of Aqua Products Robotic pool cleaners.
TABLE OF CONTENTS Table of Contents............................................................................................................................. 2 Welcome............................................................................................................................................ 2 How it Works.................................................................................................................................... 3 - 4 Operating Instructions.........................
How it Works Rather than connecting to your pool’s filter or requiring a booster pump, your cleaner is equipped with its own built-in Pump Motor that provides it the ability to vacuum dirt and debris independently. An internal, reusable Filter traps the debris allowing only clean water to pass through. The filtered water that is expelled is efficiently used to hydraulically drive or “jettison” your cleaner about the pool.
Complete Coverage Like a car, your cleaner has two Axles; the front Axle turns your cleaner and the back axle is fixed. Your cleaner will operate using one of two turning systems; Locking Pin or Mechanical Wedge. Right position Locking Pin forces Axle’s left side to slide back turning cleaner to the left when moving forwards and in straight line when reversing.
OPERATING FEATURES This manual has been created to represent the set-up and troubleshooting practices required for a variety of Aqua Products cleaners. Although the shape and color of some components featured herein may not be identical to those of your cleaner, their operating and service procedures are. As there are a variety of features and components applicable to the various models produced, some pages may show features not available on your cleaner model.
OPERATING FEATURES Figure 3a BOTTOM LID ASSEMBLY 26 19 18 24 25 21 20 24 18 Figure 3b 19 29 24 23 18 18. Bottom Lid 19. Wire Frame Bag Support 20 “H”-Float 21. Side Pocket Floats 18 22. 23. 24. 25. 24 28 Square Floats Float Screws & Washers Debris Intake Port / Flaps Filter Bag 6 22 26. 27. 28. 29.
Power Supply & Floating Cable Connections 1 Fig. 4 2 Power Supply (Transformer) with: • Built-in Forwards/Reverse Timer • Built-In 2-Hour Automatic Shut-Off 1. Power Supply 2. Power (ON/OFF) Switch 3. Socket (For Floating Cable) 4. Fuse Holder 5. Power Supply Cord 6.
QUICK SETUP INSTRUCTIONS Never allow anyone to swim in the pool while the cleaner is in the pool! STEP 1 LOCATION, LOCATION, LOCATION OF YOUR POWER SUPPLY 1. They say location is one of the most important factors, and in the case of your Power Supply, they are right. Place the Power Supply in a dry, sheltered area at least 12 feet / 4 meters away from the pool.
STEP 3 SETTING THE FORWARDS / REVERSE TIMER Green C-RUN LED If your cleaner’s Power Supply features an adjustable Timer (Dial or Digital), you can control the length of the forwards / reverse movement time of your cleaner by using the control pad on the Power Supply.
OPERATING INSTRUCTIONS WHEN TO CLEAN FILTER BAG It is suggested that you clean the Filter Bag after every use to ensure the strongest hydraulic drive and vacuum suction. When your cleaner begins to slow down considerably by constantly reversing direction before reaching portions of the pool it would normally reach, it is sending you a signal that it is time to clean the Filter Bag. Always thoroughly clean the Filter Bag and rinse your cleaner and its components prior to storing it for any length of time.
TROUBLESHOOTING Should none of the troubleshooting procedures provided herein correct your specific issue, please visit our customer service department online at AquaProducts.com/Service to view troubleshooting videos and step-by-step procedures or contact our Customer Service department via email at CustomerService@AquaProducts.com or by phone toll free at 1-800-845-4856. Moves slowly or inefficient vacuuming • Check to see if the Filter Bag is thoroughly clean.
TROUBLESHOOTING Reverses before reaching the opposite end of the pool • Turn the Time Control Dial (located on the Power Supply) clockwise a few degrees or adjust the Digital Timer using the “up” Button to increase the time between reversals. Repeat if necessary. • Check to see if the Filter Bag is thoroughly clean and installed properly. Know that the Filter Bag is capable of trapping particulates down to 20 times smaller than what is visible to the naked eye.
IMPORTANT: A Return Authorization Number (RMA) must be obtained from Aqua Products prior to shipping cleaner to its repair facility. Any item shipped to Aqua Products without a proper RMA number will be refused and returned! PREPARING YOUR CLEANER FOR SHIPPING In the event that you should have to send your cleaner in for repair, you must package the cleaner properly to ensure it reaches the repair facility safely and without incurring damage during transport.
Include a copy of all information obtained during your contact with the technical service analyst and / or Authorized Service Center, including your contact information and cleaner’s serial number in an envelope (Fig. 6c). A copy of the information relevant to the current technical issue should be sent in the packaging with your cleaner in an envelope.
NOTES __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ __________________________________________________________________________________ ________
DO NOT RETURN CLEANER TO RETAILER! If you have a technical service issue PLEASE REFER TO THIS MANUAL OR Contact Aqua Products DIRECTLY FOR IMMEDIATE SUPPORT Note that the absolute majority of technical issues can be resolved over the phone (1-800-845-4856), by referring to this Operator manual or reviewing troubleshooting videos and information online anytime at www.AquaProducts.com/Service.
