Owners manual

CONTACT INFORMATION: Black Diamond Coatings, Inc. 8511 Sunstate St., Unit 102, Tampa, FL 33634.
www.BlackDiamondCoatings.com | 800-270-4050 | [e-mail] Page 1 of 2
© 2018 Black Diamond Coatings, Inc.
PRODUCT OVERVIEW
AQUA-X
®
11 is designed for use by professional contractors and
DIYers who demand excellent products with high performance.
AQUA-X 11 is a water-based, penetrating silicone water repellent
that provides a moisture resistant barrier on masonry and other
concrete surfaces.
FEATURES AND BENEFITS
Low VOC
ü Meets all 50 state requirements
Professional results
ü Natural finish
ü Professional grade, penetrating water-based
silicone water repellent
ü Industrial grade UV resistance
ü Fast beading action
ü Excellent water repellency
ü Protects sealed surfaces from moisture for
easier maintenance
ü Industrial grade, long-lasting protection
ü Reduces efflorescence and concrete dusting
ü Freeze/thaw protection, reduces spalling
ü Seal horizontal or vertical surfaces
Easy application
ü Water-based, one coat application
ü Easy to use
Breathable
ü Allows the surface to breathe; does not trap
moisture
PHYSICAL DATA
Product Type:
Water-based silicone
Finish:
Natural
Components:
One
Curing Mechanism:
Air dry
Coverage:
Coverage up to 600 square feet per gallon,
depending on the surface porosity and
application method
VOCs:
9 g/L
pH
4.9
Flashpoint:
>100 °C (>212 °F)
Shelf Life:
Best used by 12 months from the date of
production
Dry Time:
1-2 hours after application
Use this product on the following surfaces:
Surface
AQUA-X 11
Bare Concrete
✔
Concrete Block
✔
Clay Pavers
✔
Decorative Concrete
✔
Concrete Brick Pavers
✔
Grout
✔
Faux Stone
✔
Natural Stone
✔
Specialty Concrete*
✔
*Wetcast and specialty aggregate (exposed aggregate, shells, glass, etc.)
should be treated like natural stone.
Refer to the Safety Data Sheet for more technical detail.
TESTING DATA
Water Loss in Rilem Tubes
Time (hours)
ml
2
0.0
4
0.0
24
0.2
APPLICATION PROCESS
1. PREPARE
Clean the surfaces thoroughly.
The surface to be treated should be properly cleaned before any application
of AQUA-X 11. The surface should be free of dirt, oil, contaminants, and any
other substance that could interfere with the sealer penetrating the surface
as intended. AQUA-X 11 should not be applied to any surface that has been
modified with the addition of any admix or post treatment. If stain is to be
applied to the surface, it should be applied prior to sealing with AQUA-X 11.
Bare Concrete: New concrete must be cured a minimum of 28 days. Other
curing compounds may not be compatible. Concrete surfaces should be
clean, free of dirt, oil, grease and other contaminants. Pressure washing with
2,000 psi pressure cold water may be necessary. On older concrete surfaces;
sandblasting, shot blasting or high-pressure cold water may be used.
Chemical cleaning or high-pressure hot water may also be used. Rinse
thoroughly after chemical cleaning. The surface pores must be opened up
sufficiently to allow immediate penetration of AQUA-X 11. Substrate should
have a pH between 6-10.
2. TEST
Perform a small test area (at least 2 sq. ft.) using the product to ensure
suitability and the desired results prior to full application. Test for
application coverage rate. Use the same preparation, equipment and
conditions expected during the entire application. Due to the wide variety of
substrates, preparation methods, application methods and environments,
the customer should test the product in an inconspicuous spot for
penetration and compatibility prior to full application.
3. APPLICATION
Ensure proper surface conditions. Prior to application, the surface should be
completely dry for best results. The surface temperature should be between
30-120° F (-1-49° C), and it should be maintained for 12 hours from the start
of application. If freezing conditions exist before application, let the surface
thaw. The water carrier may freeze at low temperatures or evaporate in hot
conditions. Both conditions impair penetration and results. Do not apply if
rain is expected within 3 hours. Do not dilute or alter this product.