TDS
Table Of Contents
- PRODUCT OVERVIEW
- FEATURES AND BENEFITS
- PHYSICAL DATA
- TESTING DATA
- Water Loss in Rilem Tubes
- APPLICATION PROCESS
- Clean the surfaces thoroughly.
- Ensure proper surface conditions. Prior to application, the surface should be completely dry for best results. The surface temperature should be between 50-120( F (10-49( C), and it should be maintained for 12 hours from the start of application. If f...
- Store and handle properly.
- CUSTOMER CARE
- LIMITED WARRANTY
FEB 2022
CONTACT INFORMATION: Black Diamond Coatings, Inc. 6036 Nature Coast Blvd. Brooksville, FL 34602.
www.BDCbrands.com | 800-270-4050 | info@BlackDiamondCoatings.com Page 1 of 2
© 2022 Black Diamond Coatings, Inc.
PRODUCT OVERVIEW
AQUA-X
®
11 is designed for use by professional contractors and
DIYers who demand excellent products with high performance.
AQUA-X
®
11 is a water-based, penetrating silicone water repellent
sealer that provides a moisture resistant barrier on masonry and
other concrete surfaces.
FEATURES AND BENEFITS
Low VOC
✓ Meets all 50 state requirements
Professional results
✓ Natural finish
✓ Professional grade, penetrating water-based
silicone water repellent sealer
✓ Industrial grade UV resistance
✓ Fast beading action
✓ Excellent water repellency
✓ Protects sealed surfaces from moisture for
easier maintenance
✓ Industrial grade, long-lasting protection
✓ Reduces efflorescence and concrete dusting
✓ Freeze/thaw protection, reduces spalling
✓ Seal horizontal or vertical surfaces
Easy application
✓ Water-based, one coat application
✓ Easy to use
Breathable
✓ Allows the surface to breathe; does not trap
moisture
PHYSICAL DATA
Product Type:
Water-based silicone
Finish:
Natural
Components:
One
Curing Mechanism:
Air dry
Coverage:
Coverage up to 600 square feet per gallon,
depending on the surface porosity and
application method
VOCs:
9 g/L
pH
9 - 11
Flashpoint:
>100 °C (>212 °F)
Shelf Life:
Best used by 12 months from the date of
production
Dry Time:
1-2 hours after application
Use this product on the following surfaces:
Surface
AQUA-X
®
11
Bare Concrete
✔
Concrete Block
✔
Clay Pavers
✔
Decorative Concrete
✔
Concrete Brick Pavers
✔
Grout
✔
Faux Stone
✔
Natural Stone
✔
Specialty Concrete*
✔
*Wetcast and specialty aggregate (exposed aggregate, shells, glass, etc.)
should be treated like natural stone.
Refer to the Safety Data Sheet for more technical detail.
TESTING DATA
Water Loss in Rilem Tubes
Time (hours)
ml
2
0.0
4
0.0
24
0.2
APPLICATION PROCESS
1. PREPARE
Clean the surfaces thoroughly.
The surface to be treated should be properly cleaned before any application
of AQUA-X
®
11. The surface should be free of dirt, oil, contaminants, and any
other substance that could interfere with the sealer penetrating the surface
as intended. AQUA-X
®
11 should not be applied to any surface that has
evidence of being sealed. If stain is to be applied to the surface, it should be
applied prior to sealing with AQUA-X
®
11.
Bare Concrete: New concrete must be cured a minimum of 28 days. Other
curing compounds may not be compatible. Concrete surfaces should be
clean, free of dirt, oil, grease and other contaminants. Pressure washing with
2,000 psi pressure cold water may be necessary. On older concrete surfaces,
shot blasting or high-pressure cold water may be used. Chemical cleaning or
high-pressure hot water may also be used. Rinse thoroughly after chemical
cleaning. The surface pores must have proper ventilation to allow immediate
penetration of AQUA-X
®
11. Substrate should have a pH between 6-10. Acid
etching maybe required on smooth trialed concrete to allow proper
penetration of AQUA-X
®
.