™ WARNING: • Never attempt to swim after a stalled R/C boat. • Never operate your R/C boat while standing in the water. • Never operate your R/C boat in the presence of swimmers. • Always use a Personal Flotation Device (PFD) when boarding and operating your retrieval craft, i.e. Jon boat or duck boat. NOTE: Because of the sharp running hardware included with this R/C boat, we do not recommend a rubber blow up raft. • R/C boat running hardware is very sharp.
ITEMS INCLUDED WARRANTY STANDARD REPAIR SERVICE After the 90-day warranty has run out, you can still have your Miss Vegas Deuce repaired for a service fee by the experts at AquaCraft.To speed up the repair process, please follow these four simple steps: AquaCraft will warrant your Miss Vegas Deuce hull for 90 days after the purchase from defects in materials or workmanship of original manufacture. AquaCraft, at their option, will repair or replace at no charge, the incorrectly made part.
ITEMS NEEDED TO COMPLETE YOUR MISS VEGAS DEUCE INTRODUCTION Thank you for purchasing the AquaCraft™ Miss Vegas™ Deuce! We want the time you spend with your new R/C boat to be fun and successful, so please fully read the manual. If for any reason you think this R/C model is not for you, return it to your local hobby dealer immediately. Your hobby dealer cannot accept returns on any model after final assembly or after your boat has been operated.
INSTALLATION OF RECEIVER BATTERIES FINAL ASSEMBLY Carefully remove your Miss Vegas Deuce from the box and place it atop the pre-built boat stand. Remove all remaining components from the box. You may wish to keep the box in order to more easily transport and store your Miss Vegas Deuce. Decals have been provided for your Miss Vegas Deuce. Simply cut them out, peel, and stick! See the photos on the box for recommended decal placement. TRANSMITTER ASSEMBLY 1.
3. Remove the two 2 x 12mm screws that secure the radio box lid and gently lift the lid from the battery box. 7. Replace the canopy by first sliding it over the “nose” of the boat and then lowering the rear section to meet the hull. Secure it by sliding the two cowl locks toward the rear of the boat. 4. Install four fresh “AA” batteries in the battery holder. Be sure to follow the polarity configuration molded into the battery holder. 5. Plug the battery box connector into the ON/OFF switch connector.
PROPELLER DEPTH TRIM ADJUSTMENTS FOR THE MISS VEGAS DEUCE Here are some of the important factors that affect the performance of a hydroplane. PROPELLERS The FRP (Fiber-Reinforced Plastic) prop that comes with your Miss Vegas Deuce is about the best overall prop for daily running. If your prop has a ding or chip in a blade, you need to replace it with a new one before you run the boat again.
SUPERTIGRE .18 MARINE ENGINE Important: Please fully read these instructions before operating your engine. These instructions have been written so that you may get the greatest satisfaction from the operation of your new engine. SPECIFICATIONS: ABC Piston and Sleeve Bore: .662" Stroke: .535" Displacement: .184ci (3cc) Power Output: 1.
STARTING YOUR ENGINE: RUNNING THE MISS VEGAS DEUCE PLEASE TAKE THE TIME TO DO THE FOLLOWING. Using the provided 12mm and 14mm wrenches, loosen the cable coupler and slide the cable out the back of the boat. Make sure there is adequate grease on the shaft (see page 11). Reinstall the cable leaving about 3mm [1/8"] between the back of the strut and the front of the drive dog. Tighten the cable coupler making sure it is tight.
ENGINE BREAK IN: It can be somewhat difficult to tune and break in a marine glow engine, as tuning and break-in are best done with the boat on the water. Take your time and do not hurry the break in. If you operate the engine too lean in the early break-in stages, you could damage it. Factory needle settings: HSN: 4 turns out LSN: 2-1/2 turns out NOTE: Due to atmosphere changes the factory needle setting could be too rich or too lean.
GET TO KNOW THE SOUNDS AND SIGHTS OF YOUR NITRO MARINE ENGINE: • Rich needle setting means less than maximum RPM. The engine will operate with a break in the exhaust note. Also take note that when rich, your engine is going to use more fuel than normal and you’re going to end up with a lot of oil and smoke coming out of the exhaust pipe. WAYS TO ENSURE A LONG LIFE FOR YOUR ENGINE: • Keep your engine clean. Dirt will act as insulation on an engine. It will not be able to shed heat as easily.
MAINTENANCE When you are through operating your boat for the day, be sure to perform these basic maintenance procedures. This will prolong the life of the Miss Vegas Deuce and help to ensure trouble-free running. ENGINE MAINTENANCE Drain the tank of any remaining fuel. Add some after-run oil to the engine to protect the internal parts. We recommend removing the glow plug, opening the carburetor all the way, and placing 10–12 drops of after-run oil down the barrel of the carburetor.
SUPERTIGRE .
ORDERING REPLACEMENT PARTS RACING To order replacement parts for the AquaCraft Miss Vegas Deuce use the order numbers in the replacement parts list that follows. Replacement parts can be purchased from your local hobby shop or by mail order. If you need assistance locating a dealer to purchase parts, visit www.hobbico.com and click on “Where to buy”.
NATIONAL MODEL BOATING ORGANIZATIONS The length of the races can be determined by a set number of laps around the buoys (for example, the first boat to complete five (5) laps is the winner); or by time (for example, whoever is leading at the end of two (2) minutes is the winner). There are two national model boating organizations in the United States and Canada: IMPBA or International Model Power Boat Association www.impba.net NAMBA or North American Model Boat Association www.namba.
™ Assemble a competition-class wood tunnel hull in just 6-8 hours! Hull Length: 28 in (711 mm) Beam: 11 in (280 mm) Height: 5.25 in (130 mm) Ready-to-Run Weight: 4 lb (1814 g) Requires: 2+ channel radio with one high-torque standard servo and one mini servo, .21 cu in (3.5 cc) outboard engine The kit form of this Mike “Grimracer” Zaborowski design took the first of its 10 titles at the 2000 IMPBA Internats.
COPYRIGHT © 2009 AQUB34**MNL v1.