Goliath Drain Pan Installation Instructions

ManualsBrandsAquaGuard Manualsair conditioning coolingDrain Pan

Rev. 10/08

AG-4100

AG-4200

AG-4300

Installation Instructions:

Titan, Spartan, Goliath and Goliath Furnace Series

Secondary Condensate Pans & 4000 Series Switches

Work Safe, READ THIS!

ATTENTION: FAILURE TO READ AND COMPLY WITH ALL WARNINGS, CAUTIONS AND INSTRUCTIONS PRIOR TO STARTING INSTALLATION MAY

CAUSE PERSONAL INJURY AND/OR PROPERTY DAMAGE AND VOID WARRANTY.

STOP/READ: This device must be installed in accordance with manufacturer’s instructions. This unit must be in accordance with all applicable local plumbing, drainage and

electrical codes.

WARNING: Remove electrical shock hazard – DISCONNECT THE POWER BEFORE INSTALLATION to avoid electrical shock and/or equipment damage. Do not use

on circuits exceeding 24 volts to avoid damage to switch, shock or fire hazard.

CAUTION: In some situations the switch may cause the unit to rapidly cycle on and off as water level rises slowly in pan. After a brief period the unit will turn off completely.

Condensation drain must be serviced if this occurs.

CAUTION: In any installation where property damage and/or personal injury might result from an inoperative switch due to power outages, a back-up system(s) and or alarm

should be installed.

NOTICE: The AquaGuard Drain pans and float switches must only be installed by a licensed contractor or under the direct supervision of same. Condensation pan must be

properly maintained after installation and be kept free from foreign objects, rust or other obstructions that might interfere with the proper operation of the AquaGuard float

switch.

TITAN DRAIN PAN INSTALLATION:

(To ensure proper performance of product, instructions must be followed.)

1. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.

2. Make sure drain pan is a minimum of 3” greater (1.5” clearance per side) in length and width than the equipment dimension.

3. Make sure the pan-mounting surface is level and free of any debris.

4. For solid surface applications, place HVAC unit on blocks or 2-4x4 boards running the full length of the Titan pan between the HVAC unit and the Titan pan between

the HVAC unit and the pan on either of the water displacement ridge. (fig. 1)

5. For hanging application, place 2-4x4 boards running the full length of the Titan pan between the HVAC unit and the pan on either side of the water displacement

ridge. (fig. 2). Pressure treated wood will not damage the pan.

6. Approved steel supports are to be placed 6” to 8” from the end of the 4x4 as shown. (fig. 3).

IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s recommended that a damp cloth be

placed under the lines being brazed.

(fig. 1) (fig. 2) (fig. 3)

HORIZONTAL INSTALLATION OF SPARTAN, GOLIATH, AND GOLIATH FURNACE DRAIN PAN:

(To ensure proper performance of product, instructions must be followed.)

1. Refer to Furnace/Air Handler instructions prior to installation.

2. Inspect the drain pan for any shipping damage that may have occurred. If cracked or broken, DO NOT USE.

3. Make sure drain pan is a minimum of 3” greater (1.5” clearance per side) in length and width than the equipment dimension.

4. Make sure the pan-mounting surface is level and free of any debris.

IMPORTANT! When brazing, take precautions to prevent pan from coming in contact with torch heat or brazing materials. It’s recommended that a

damp cloth be placed under the lines being brazed.

5. Insert rubber Vibration Isolators (Spartan, Goliath and Goliath Furnace series only) in the most appropriate support receptacles. (fig.4) It is not necessary to fill every

receptacle.

6. For non-furnace applications, position air handler in the center of the pan. (fig. 5)

7. For furnace installations, refer to manufacturer’s instructions regarding clearance specifications. Optional AG-MJ1 Riser Kit may be used to achieve additional

1” clearance between furnace and pan.

8. For furnace installations, position the furnace with the heavy side of the unit resting on “back side” of the pan, i.e. the side directly opposite of the float switch. (fig.

Caution: AquaGuard SPARTAN and GOLIATH FURNACE SERIES Drain Pans are not designed for hanging applications.

Summary of content (8 pages)

PAGE 1
AG-4100 AG-4200 AG-4300 Installation Instructions: Titan, Spartan, Goliath and Goliath Furnace Series Secondary Condensate Pans & 4000 Series Switches Work Safe, READ THIS! ATTENTION: FAILURE TO READ AND COMPLY WITH ALL WARNINGS, CAUTIONS AND INSTRUCTIONS PRIOR TO STARTING INSTALLATION MAY CAUSE PERSONAL INJURY AND/OR PROPERTY DAMAGE AND VOID WARRANTY. STOP/READ: This device must be installed in accordance with manufacturer’s instructions.
PAGE 2
Unit (fig. 4) (fig. 5) Goliath Air Handler Pan Installation: • • • Goliath Furnace and Spartan Pan Installation: Safely hang or place pan on flat level surface. When hanging, pans must be supported equally at least 8” from each end by an approved support system, and approved by local code. Check your local building codes before installation. • • • • DO NOT HANG Goliath Furnace or Spartan pans! Position pan on flat level surface only. Follow all manufacturer’s installation instructions.
PAGE 3
2. 3. Install the drain housing from inside the pan MAKING SURE THE RUBBER GASKETS ARE ON THE INSIDE OF THE PAN. (fig. 9) Screw the nut onto the drain housing from outside the pan and securely hand tighten. (fig. 10) Drain Housing Threaded Nut Rubber Gasket Drain Housing Threaded Nut (fig.10) (fig. (9) 4. Install the Float Switch onto the Drain Housing by inserting flat plastic slide into the corresponding receptacle on the housing. (figs. 10,11,12) Slide Down & insert Switch (fig.
PAGE 4
(To ensure proper performance of product, instructions must be followed.) 1. 2. 3. 4. 5. Double check that the power is disconnected to the unit at the main panel prior to moving to step 2. Refer to the appliance manufacturer’s installation and operating instructions and also review wire layout in their instructions. Locate the red wire coming from the 24 volt thermostat “R” terminal. Disconnect or cut red wire. Connect to one of the switch leads using wire nut.
PAGE 5
AG-4100 AG-4200 AG-4300 Instrucciones de Instalación: Bandejas Titan, Spartan, Goliath y Series de Calefacción Goliath Bandejas de Condensación Secundarias y Series de Suiches 4000 Trabaje con Precaución, LEA ESTO! ATENCIÓN: OMITIR LA LECTURA RELACIONADA CON LA INSTALACIÓN, ADVERTENCIAS Y PRECAUCIONES ANTES DE COMENZAR LA INSTALACIÓN, SE PUEDEN CAUSAR DAÑOS Y PREJUICIOS CORPORALES, ADEMÁS DE CAUSAR DAÑOS AL PRODUCTO Y PERDER LA GARANTÍA.
PAGE 6
8. Para la instalación de bandejas de calefacción, posicione el equipo con la parte más pesada sobre la parte trasera de la bandeja, es decir, colocarla en el lado opuesto al suiche flotador (fig. 4) Precaución: La bandeja de AquaGuard SPARTAN y las Series de bandejas de drenaje de calefacción GOLIATH no son diseñadas para aplicaciones en que se requiere guindar la bandeja. Vibration Isolators (fig. 4) (fig.
PAGE 7
Drenaje Suiche Flotador (fig. 8) 2. 3. Instale el drenaje desde la parte de adentro de la bandeja ASEGURÁNDOSE QUE LAS JUNTAS DE GOMA ESTÉN POR LA PARTE DE ADENTRO DE LA BANDEJA. (fig. 9) Enrosque la tuerca al drenaje por la parte de afuera de la bandeja y apriete la tuerca con la mano. (fig. 10) Tuerca con rosca Drenaje Junta de Goma Drenaje Tuerca con rosca (fig. 9) (fig. 10) 4.
PAGE 8
Pruebe las líneas de condensamiento en caso de ser requerido de acuerdo a los códigos aplicables. CABLEADO DEL AG-4100, AG-4200 Y AG-4300: (Se deben seguir las instrucciones para asegurar el correcto funcionamiento del producto). 1. 2. 3. 4. 5. Verifique que la electricidad esté desconectada de la unidad principal antes de seguir con el siguiente paso. Refiérase a las instrucciones de instalación y funcionamiento de la unidad de aire acondicionado o de refrigeración y también revise el cableado.