Manual

ManualsBrandsAquametrix ManualsAccessories for waterIP80 Series Paddle Wheel Sensors

Features

• Low-friction, long-life jewel bearings

• Single moving part

• Six bladed impeller

• Fully eld-repairable

• Choice of materials for compatibility

with variety of chemicals

• Integrated Tee and sensor

• Fits 1/2” to 8” pipe sizes

• Fixed depth in tting ensures proper

placement in pipe

• High level signal can be sent up to

2000 feet

• Each tting individually calibrated

and marked with K-factor (Pulses per

Gallon)

The IP80 series are impeller type (or “paddlewheel”) insertion meters de-

signed for use with a wide variety of liquids in pipe sizes 1/2” to 8”. Sensors

are available in brass, 316 stainless steel, PVC, and polypropylene. Bodies

are machined from a solid rod for maximum precision. High-quality jewel

bearings and nickel-bound tungsten carbide shafts are used for extreme low

friction and long life.

The rotation of the rotor is detected by a non-drag Hall-effect sensor. Output

is a current-sinking pulse (square wave), which can be sent long distances

(up to 2,000 feet) without a transmitter. This signal can be connected directly

to PLC’s, counters, and computer cards, as well as a variety of AquaMetrix

controls and displays.

For rate and total display, the Shark-120/240 controller or Shark TX/P trans-

mitter (loop powered) models are compatible with IP80 series sensors. They

can be mounted in either surface, pipe

or panel congurations.

The IP80 series require special ttings

that ensure correct depth placement in

the pipe. Fittings come in a variety of

materials for compatibility with specic

applications. Tee ttings are individu-

ally wet-calibrated at the factory and

marked with the K-factor (pulses per

gallon). Saddle ttings must be eld-

installed on the pipe and do not come

wet-calibrated. K-factors for saddles

are based on factory testing.

Description

100 School Street

Andover, MA 01810

978-749-9949

Toll free - 855-747-7623

www.WaterAnalytics.net

Applications

• Waste water ow

• Water Treatment systems

• Irrigation

• Groundwater Remediation

• Chemical Mixing

• Process cooling systems

• Neutralizaton Systems

• Process ow control

• Filtration systems

Model IP80 Series

Impeller Flow Sensor

Water Analytics

Aqua

Metrix

Water Analytics

Aqua

Metrix

Summary of content (2 pages)

PAGE 1
AquaMetrix by Model IP80 Series Impeller Flow Sensor Water Analytics Features • Low-friction, long-life jewel bearings • Single moving part • Six bladed impeller • Fully field-repairable • Choice of materials for compatibility with variety of chemicals • Integrated Tee and sensor • Fits 1/2” to 8” pipe sizes • Fixed depth in fitting ensures proper placement in pipe • High level signal can be sent up to 2000 feet • Each fitting individually calibrated and marked with K-factor (Pulses per Gallon) Descripti
PAGE 2
Model IP80 Series Impeller Flow Sensors Technical Data Materials Sensor Body Rotor Shaft Flow Range (GPM) PVC, Polypro, Brass, or 316 SS PVDF Nickel-bonded tungsten carbide (Ceramic optional) Ruby jewel EPDM (Viton optional) Bearings O-Ring Pipe Size IP81 1/2” to 3” (12 to 76 mm) IP82 4” to 8” (100 to 200 mm) Maximum Pressure PVC or Polypro 175 PSI (12 bar) at 75º Brass 200 PSI (14 bar) 316 SS 250 PSI (17 bar) Maximum Temperature PVC or Polypro 130ºF (55ºC)* Brass or SS 200ºF (93ºC) Flow Rate 0.