Model 55011-7 OWNER’S MANUAL UTILITY SINK PUMP Questions, problems, missing parts? Before returning to the store call AQUAPRO Customer Service 8 a.m. - 5 p.m., EST, Monday-Friday 1-844-242-2475 © 2015 Copyright GP Enterprises Co., Ltd.
PERFORMANCE Model HP 55011-7 1/3 GPH of Water @ Total Feet Of Lift 0 ft. 5 ft. 10 ft. 1300 950 550 Max. Lift 15 ft. SAFETY INSTRUCTIONS 1. Do not pump flammable or explosive liquids such as oil, gasoline, kerosene, ethanol, etc. Do not use in the presence of flammable or explosive vapors. Using this pump with or near flammable liquids can cause an explosion or fire, resulting in property damage, serious personal injury, and/or death. 2. ALWAYS disconnect the power to the pump before servicing. 3.
18. Ensure the electrical power source is adequate for the requirements of the pump. 19. This pump is made of high-strength, corrosion-resistant materials. It will provide trouble-free service for a long time when properly installed, maintained, and used. However, inadequate electrical power to the pump, dirt, or debris may cause the pump to fail. Please carefully read the manual and follow the instructions regarding common pump problems and remedies. 20.
INSTALLATION (SEE FIGURES 1 AND 2) WARNING: Electric Shock Hazard. Plug pump into a properly grounded, GFCI protected outlet. Do NOT plug in the pump until after it is completely installed. Do not remove or modify the grounding pins on the plugs. Fittings Supplied: Qty. A Sink Drain Screen 1 B 1-1/4” NPT x 1-1/4” Slip Check Valve 1 C 1-1/4” NPT Ball Valve 1 Purchase Separately: Qty.
Mount the pump NOTE: DO NOT use plumber’s pipe threading compound (“pipe dope”) on plastic pipe; it can damage the plastic, causing leaks and piping failure and void the warranty. 1. Place the sink in its final location. 2. Remove any existing drain fittings back to the tail piece. Make sure the existing tail piece does not leak. NOTE: If the sink-drain tail piece is not 1-1/2 in. NPT, you will have to adapt it (bushings, reducers, etc.).
8. Slide the pump up into position and glue the pipe into the male adapter (on the pump). •No glue on the pump or in the motor; • Make sure the pump is facing the right direction (match the marks from Step 7); • Put the support in place under the motor. 9. Wrap the 1-1/4 in. galvanized nipple with 1-1/2 to 2 turns of PTFE pipe thread sealant tape on each end and thread it into the pump discharge port. NOTE: Tighten this only enough to prevent leaking. Over-tightening can crack the plastic. 10.
Washing Machine Use Washing machines usually discharge more water than the faucets do, and it is normal for the water level to rise in the sink while the pump is discharging. Do not adjust the discharge valve to match the flow when the washing machine discharges into it, unless the sink is ONLY used for washing machine discharge. † For easier removal for servicing or cleaning, install a 1-1/2 in. solvent union in the drop pipe.
Figure 4: Remove 6 housing screws to clean out pump TROUBLESHOOTING Problem Pump does not run when water flows in from the sink. Pump runs but does not empty the sink. Possible Cause 1. The pump is unplugged. 2. There is no power to the outlet. 3. The pump impeller is jammed. 4. The sink stopper is in the drain. 1. The drain is clogged. 2. The discharge line is clogged. 3. The shut-off valve is closed. 4. The system discharge line is too high or too long. 5. The check valve is installed backwards.
WARRANTY Limited One-Year Warranty WHAT THIS WARRANTY COVERS When used and maintained in normal use and in accordance with the Owner’s Manual, your AQUAPRO product is warranted against original defects in material and workmanship for one full year from the date of purchase (the “Warranty Period”). During the Warranty Period, AQUAPRO will repair or replace at no cost to you, to correct any such defect in products founds upon examination by AQUAPRO to be defective in materials or workmanship.
Model 55011-7 MANUAL DEL USUARIO BOMBA DE USO GENERAL PARA FREGADERO ¿Preguntas, problemas, piezas que faltan? Antes de devolverla a la tienda, llame a Servicio al Cliente de 8:00 AM a 5:00 pm EST de Lunes a Viernes.
RENDIMIENTO Model CP 55011-7 1/3 GPH (Galones por hora) de Agua @ Pies (Metros) de Altura 0pi.. 5pi. 10pi. 1300 950 550 Máx. Levante 15pi. INSTRUCCIONES DE SEGURIDAD 1. No bombee líquidos inflamables o explosivos con aceite, gasolina, queroseno, etc. No lo use cerca o en presencia de vaporesinflamables o explosivos. El uso de este producto cerca o con líquidos inflamables puede causar una explosión o un incendio causando daños a su propiedad, lesiones personales, y/o muerte. 2.
17. El motor de la bomba tiene un protector térmico automático de reajuste que se apaga si la bomba se recalienta. Una vez que el protector térmico detecte que la bomba ha bajado de temperatura permitirá que la bomba funcione normalmente. Si la bomba está conectada puede empezar a funcionar inesperadamente. 18. Asegure que la fuente de electricidad es adecuada para los requisitos que exige la bomba. 19. Esta bomba está hecha de materiales de alta fuerza y resistentes a la corrosión.
INSTALACIÓN (VER FIGURAS 1 Y 2) ADVERTENCIA: Peligro de choque eléctrico. Enchufe la bombaen un tomacorriente debidamente puesto a tierra y protegido porun disyuntor de escape a tierra, (GFCI). NO enchufe la bombahasta después de haber terminado la instalación. No retire nimodifique las clavijas de conexión a tierra en las fichas.
Montaje de la bomba AVISO: NO use un compuesto de plomería para roscas detuberías (compuesto lubrificante) en tuberías de plástico, ya quepuede dañar el plástico, provocar fugas y fallas en la tubería einvalidará la garantía. 1. Coloque el fregadero/la pileta en la ubicación final. 2. Saque todos los accesorios de desagüe presentes hasta elcabo de conexión. Verifique que el cabo deconexión presente no tenga fugas.
7. Haga una prueba para armar la bomba (en seco - sin pegamento)en la tubería de desagüe. Haga balancear la bombahasta que quede precisamente orientada hacia la tubería dedesagüe, y luego marque tanto la bomba como la unidad dela tubería de admisión/adaptador, para poder instalar labomba correctamente en el Paso 8. Coloque un soporte provisionaldebajo de la bomba para aliviar la tensión sobre latubería de descarga del fregadero/de la pileta, hasta que elpegamento se haya endurecido.
Cómo regular el flujo Cómo regular el flujoLa bomba de drenaje puede bombear hasta 21 galones porminuto (GPM). Los drenajes normales de fregaderos permiten unflujo de sólo 5 a 6 GPM. Ajuste la llave de paso de la descarga /equilibradora de flujo de la siguiente manera para que la bombano se encienda y se apague continuamente cuando los grifos estén totalmente abiertos. Deje correr agua hacia el fregadero. La bomba se encenderácuando detecte agua. Verifique que no haya fugas.
CUIDADO Y LIMPIEZA PRECAUCIÓN:Siempre utilice el mango para levantar la bomba. Nunca use el cable de conexión para levantar la bomba. Para prevenir quemaduras en la piel, desenchufe la bomba y dele tiempo a que se enfríe después de periodos extensos de uso. Esta bomba requiere muy poco mantenimiento y deberá proporcionarleun servicio prolongado. Los problemas son raros;cuando el flujo de la bomba desciende, la causa más probablees que algo sólido pueda haber caído por el desagüe y estétrabando el impulsor.
RESOLUCIÓN DE PROBLEMAS Problema La bomba no marcha cuando corre agua desde el fregadero La bomba marcha, pero no vacía al fregadero Causas Probables 1. La bomba está desenchufada. 2. El tomacorriente no tiene potencia. 3. El impulsor de la bombaestáatascado. 4. Tapón del fregadero en el desagüe. 1. Drenaje obstruido. 2. Tubería de descarga obstruida. 3. Llave de paso cerr. 4. Tubería de descarga del sistemademasiado alta o demasiado larga.
GARANTÍA Garantía de un Año Limitada LO QUE CUBRE ESTA GARANTÍA Cuando usted usa y mantiene uso normal de acuerdo con el Manual del Usuario, su producto AQUAPRO tiene garantía contra defectos de fábrica en cuanto al material y la mano de obra por un todo un año desde la fecha de compra (el “Periodo de Garantía”).