FORTITUDE PRO SERIES WHOLE HOUSE WATER FILTER OWNER’S MANUAL FOR MODEL NO.
TABLE OF CONTENT 2 2 4 INSPECTION & PREPARATION I. Be Familiar with the System Before Installation II. System Operation Parameter and Installation checklist 4 5 5 6 6 7 7 INSTALLING THE SYSTEM STEP 1. Checking the Direction of Water Flow STEP 2. Shutting off the main water supply valve STEP 3. Mounting the 20” High Flow Sediment Filter STEP 4. Attaching the water supply pipe STEP 5. Installing the filter STEP 6.
WELCOME Thank you for choosing Aquasure. Before you start using your Aquasure Fortitude V Series Whole House Water Filter. Please take a few minute to become familiar with the basics. Filter replacement Be Sure to change your Aquasure Filters according to the recommended filter replacement schedule. This help keep your Aquasure Whole House Water System running in top condition. INSPECTION & PREPARATION I.
II. System Operation Parameter and Installation checklist IMPORTANT! The following condition for feed water supply must be met or warranty will be void and manufacturer assumes no responsibility for damage to system or property. 1. Water Temperature Parameter • Maximum: 100º F (37.8º C) • Minimum: 40º F (4.4º C) 2. Water Pressure Parameter • Maximum: 75 PSI (5.98 kg/cm2) • Minimum: 20 PSI (1.41 kg/cm2) 3. pH Parameter • Maximum: 10 • Minimum: 5 4.
INSTALLING THE SYSTEM IMPORTANT! Locate and test the main water supply valve to the housing before installing the system. If the main water supply valve fails to shut off the water completely during the test, we recommend contacting your local plumber to fix the valve before begin installing the system. WARNING! If this system is install in a metal (Conductive) plumbing system, i.c. copper or galvanized metal, the plastic components of the system will interrupt the continuity of the plumbing system.
STEP 1. Checking the direction of the water flow 1. Make the water flow to make sure they are going from left to right or right to left. 2. Reassemble the mounting bracket for the pleated sediment filter if the direction is oppsite of where the mounting bracket is facing. 3. Make sure the flow fo the water goes into the opening that indicated “IN” on top of the CAP and exit from the opening that indicated “OUT”. IN IN STEP 2. Shutting off the Main Water Supply Valve 1.
STEP 3. Mounting the System 1. Position the system on the wall at the desired mounting location with minimum of 6 in ground clearance from the floor to the base of the system. 2. Using a pen or pencil and mark the mounting hole on the back of the bracket onto the wall. Note: Please make sure the bracket mount is leveled using a leveling tool to ensure evenly distributed stress on the bracket. Make sure the mounting point is position on a stud to properly secure the bracket. 3.
STEP 5. Installing the Filter 1. Unwrapped the filter and place it inside the housing and make sure the housing is centering on the stand pipe. 2. Screw on the housing with the filter inside and screw onto the corresponding head by turning it counterclockwise using the supplied housing wrench. Note: Make sure the o-ring is inside the housing and do not over tightening the housing. STEP 6. System Startup WARNING! Immediately shut off the main water supply valve if there are leaks.
LIMITED PRODUCT WARRANTY Scope: Aquasure takes pride in selling a superb line of products, including this whole house water filter (“Product”). As such, Aquasure expressly warrants to the original purchaser that, for a period of Five (5) year from the date of purchase, the product will be reasonably free of defects in materials and workmanship.
Condition that render this limited product warranty void THIS LIMITED PRODUCT WARRANTY SHALL BE VOID IF: 1. The Product is not operated in compliance with normal municipal water conditions for which the particular model of this Product is intended. 2. The person seeking to invoke the warranty is not the original purchaser. That is, this Limited Product Warranty only extends to original purchasers. 3. The product is purchased used. That is, this Limited Product Warranty only covers new products. 4.
www.AquasureUSA.com | 818 N Mountain Ave #203c, Upland, CA 91786 | 800.661.0680 | sales@aquasureusa.