Instructions / Assembly

— 7 —
Aquatic • 8101 E. Kaiser Blvd. • Anaheim, CA 92808 • [phone] • FAX [phone] • www.aquaticbath.com
Installation Data
Freedomline 4-Piece Showers
F1364P, F1424P*, F1604P
Fax on Demand # 1163
Aquatic products may be specified as Lasco Bathware.
CLEAN-UP
CAUTION: DO NOT USE heat or solvent based cleaning fluids.
NOTE: Do not remove warranty/maintenance adhered label. Warranty/User maintenance label must be left for occupant
(Required by ANSIZ124).
1. Prevent staining. Remove all debris before plumbing leak test. Drain and wipe clean immediately after the inspection process.
Use sponge with warm water and liquid detergent. Rinse, drain and wipe clean. Do not use abrasive cleansers such as
scouring powders, steel wool, metal scrapers, sandpaper or anything else that might mar, dull or scratch the finish. Roofing
tar or paints may be removed with rubbing alcohol or paint thinner (not lacquer thinner).
2. Plaster and latex paint may be removed with warm water, liquid detergent and brittle brush or plastic scraper. Do not use
metal scrapper or utensil to remove plaster or paint from finish.
3. Dull areas and light scratches can be restored to high gloss with white or cream-colored automotive rubbing compound,
followed by application of coat or good quality white automotive polish (or similar) and buff with a soft cloth. Do not wax
bottom of unit.
4. Remove minor scratches with 600 grit wet/dry sandpaper, followed by step #3.
5. Major gouges require professional repair.
6. See user maintenance label for more details.
USER MAINTENANCE INSTRUCTIONS
IMPORTANT! Use only recommended cleaners and procedures described herein. Use of other materials and methods may damage
your bath fixture and void the warranty.
1. For normal cleaning, never use abrasive cleaners such as scouring powders or pads, steel wool, scrapers, sandpaper or
anything else that could scratch or dull the surface of your Aquatic unit. Instead, use warm water and liquid detergents or
non-abrasive cleansers, especially those bathroom cleansers recommended for fiberglass.
2. To keep your Aquatic bath fixture sparkling clean, apply a coat of good quality automotive paste wax or polish and buff to a
high shine with a soft cloth or towel. Repeat every six months for easier cleaning and long lasting protection. DO NOT WAX
standing surfaces of the unit bottom (this includes textured, slip resistant standing surfaces), which could result in greater risk
of slipping and personal injury.
3. To restore a scratched or dull unit, use an automotive polishing compound applied with a clean cotton rag. Rub scratches
and dull areas vigorously. Wipe off residues. Follow with automotive wax treatment described above. DO NOT WAX
standing surfaces of the unit bottom (this includes textured, slip resistant standing surfaces), which could result in greater risk
of slipping and personal injury.
4. To remove adhesive, try 3-M® natural cleaner, De-Solv-It® or similar materials. If residues remain, saturate small white
cotton rag with nail polish remover and rub vigorously until the adhesive dissolves and disappears. These solvents are highly
flammable and must be used sparingly and with caution. Do not allow solvent to go down the drain. Make sure not to
contact plastic drain grates or other synthetic materials.
5. Rubber mats: If you use rubber “anti-skid” mat, make sure to remove it from the unit after each use to avoid harm to the
surface finish.
6. Hard Water: Water in certain regions, if not wiped up after bathing/showering, may cause fading of some bath fixture
colors. This is a natural occurrence beyond Aquatic’s control. (See Warranty)
CAUTION: When using any cleaning or polishing materials, make sure to read and follow all package instructions carefully.
Wear rubber gloves at all times and avoid contact with eyes, skin, clothing, rugs and furnishings. Make sure all residues are
rinsed off thoroughly.