Note: Read all instructions before proceeding with installation. All specifications are ± 1/4’’ and are subject to change without notice.
TABLE OF CONTENTS Table of contents Product Registration/Warranty Card Congratulations! 2 3 4 Safety Instructions 5 Installation Instructions Pre-Installation Procedures Structural Preparation Leveling of the Infinity I Factory Installed Tile Flange Plumbing/Rough-In Measurements Fast Fill Waterfall Spout Continuous Waterfall Electrical Installation Chromatherapy LED Lighting 6 7-8 8 9 9-10 10 11 11-14 14 Operation Bathside Control Systems Jet Operations User Information FCC Information Serial Number
Aquatic Product Registration Information Your product warranty is registered and confirmed with Aquatic through the Serial Number on your unit. You do not need to contact Aquatic to confirm registration. Please fill out the information below and reference when contacting the distributor to expedite warranty claims. Owner Information: Model Name Serial Number (See Table of Contents for Location) Purchase Date Distributor 8101 E. Kaiser Blvd. • Anaheim, CA 92808 (800) 877-2005 • Fax (714) 998-5340 www.
congratulations! You have chosen one of the finest bath products in the world! Aquatic supports your purchase with strong commitments to quality and customer satisfaction. Please read and follow all of the instructions contained in this Owner’s Manual before installing, operating or maintaining your whirlpool. In addition, you should continually refer to these instructions during the life of your whirlpool. Failure to comply with these instructions may invalidate your warranty.
IMPORTANT SAFETY INSTRUCTIONS warning: when using this unit, these basic precautions should be followed. This manual contains information and instructions for proper operation and maintenance of your whirlpool. Failure to follow these instructions could result in personal injury, electrical shock or fire. READ AND FOLLOW ALL INSTRUCTIONS danger! To reduce the risk of injury: A. Do not permit children to use this unit unless they are closely supervised by an adult at all times.
INSTALLATION INSTRUCTION GUIDELINES READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLATION PRE-INSTALLATION PROCEDURES: please note: the manufacturer accepts a 1/4” variance. there are variations on each tub and specifications are subject to change as we improve upon our product as required. the dimensions needed for site preparation and structure buildings should be measured from the tub; Aquatic assumes no responsibility for preparatory work.
INSTALLATION INSTRUCTIONS STRUCTURAL PREPARATION: Note: The bath should remain in its shipping carton until time of installation. 1. Literature dimensions are for reference only. Installation dimensions should be taken directly from the tub. An access panel of 20” x 18” minimum must be provided at the pump end of the whirlpool allowing sufficient clearance to make final connections and for servicing the pump and power panel.
INSTALLATION INSTRUCTIONS STRUCTURAL PREPARATION (continued): 5. When placing the tub on a platform or cut out (see Diagrams), the opening should be 1” smaller than the specified rim dimensions. Extreme care must be taken in this type of installation to ensure the tub will come to rest entirely on the leveling feet. 6. IF YOU HAVE PURCHASED A WHIRLPOOL WITH AN INSTALLED TILE FLANGE, PROCEED TO INSTRUCTION “2A”. leveling of the infinity 1: 1.
INSTALLATION INSTRUCTIONS Factory installed tile flange: SEE ILLUSTRATION 2A A. Install the whirlpool bath unit per the instructions provided in this manual. CAUTION: THE TILE FLANGE DOES NOT SUPPORT THE TUB! A ledger board must be provided under the bath rim as indicated in the installation instructions. Take care to ensure tub is not hanging from the ledger boards, as this will void your warranty. B. Use nails or screws to secure the flange into the studs around the bath. C.
INSTALLATION INSTRUCTIONS Rough-In Measurements: See Diagram 3A, below MODEL A B (From center of overflow pipe to outside rim) (From center of drain to tub rim) Infinity 1 Infinity 2 Infinity 3 Infinity 4 Infinity 5 Infinity 6 Infinity 7 Infinity 8 Infinity 9 3” 2 3/8” 1 3/8” 3” 3 1/2” 5” 5” 7” 2 1/2” 24 1/2” 9 1/2” 10 1/2” 11 3/4” 11” 11 3/4” 11” 14 1/2” 8 3/4” B PLEASE NOTE: The manufacturer accepts a 1/4” variance.
INSTALLATION INSTRUCTIONS Continuous waterfall (infinity 1): The Infinity 1 is equipped with a continuous waterfall that is powered by a recirculation pump. The recirculation pump is plugged into your maintenance heater (see Diagram 4A, pg. 13). The maintenance heater must be plugged in for the continuous waterfall to be operational (see Diagram 4A, page 13). See page 15 for operation instructions.
INSTALLATION INSTRUCTIONS electrical installation (continued): breaker panel HEATER MAIN 15 AMP 2 POLE GFCI BREAKER 15 AMP 1 POLE GFCI BREAKER RED WHITE BLACK GROUND WHITE BLACK GROUND BLOWER Please see Diagrams 4A and 4B. (page 13) Bonding wire: Connect a #8 bare copper bonding wire from the pump motor to the heater and then to the cold water plumbing or other suitable ground. Grounding is required. For built-in and custom units, install to permit access for servicing.
4A HEATER AC INPUT Infinity Electronic T-Heater MAIN AC INPUT MODEL NUMBER: HS AUX CP SEQUENCER CONTROL BOX RECIRCULATING PUMP (Infinity I Only) Blower Motor OUTLET SUPPLIED WITH WHIRLPOOL (SEE WIRING DIRECTIONS) Blower Control Box 15 AMP, 120 VAC 4B Aquatic 13
INSTALLATION INSTRUCTIONS electrical installation (continued): CAUTION: Before use of the pump and heater, test the GFCI for proper operation. The pump and heater should turn off when the GFCI “Test” button is pushed. Warning - Prolonged Immersions in Hotter Water May Induce Hyperthermia. Hyperthermia occurs when the internal temperature of the body reaches a level several degrees above the normal body temperature of 98.6o F.
operation of INfinity series whirlpools NOTE: DO NOT START PUMP UNTIL ALL JETS ARE SUBMERGED. WATER LEVEL SHOULD BE 2” ABOVE HIGHEST JET. BATHside CONTROL SYSTEMS: Infinity On/Off with Heater control (See Diagram 6A): 1. To Turn Pump On: Pressing the On/Off button will turn the pump on. Pressing a second time will turn the pump off. A built-in timer will turn the pump and heater off after 20 minutes. 2. To Change Temperature: The heater and buttons are used to set water temperature.
operation of INfinity series whirlpools BATHside CONTROL SYSTEMS (continued): infinity jet sequencer control (see diagram 6b): 1. To Turn Jet Sequencer On: Pressing the “On/Off” button will turn the jet sequencer on. The system will then perform an indicator light test and open all valves. Pressing the “On/Off” button a second time will turn the jet sequencer off. A built-in timer automatically turns the jet sequencer off after 2 hours, unless manually deactivated first.
operation of INfinity series whirlpools BATHside CONTROL SYSTEMS (continued): infinity air bath control (see diagram 6c, page 16) (continued): 3. To Change Speeds: In constant mode, pressing and holding the “+” button will increase the variable speed of the blower to the maximum. Pressing and holding the “—” button will reduce the blower’s variable speed to the minimum. In both cases, the user can release the button at the desired power level.
operation of Infinity series whirlpoolS jet operations: All Infinity Series jets are removable and can simply be put into the dishwasher for cleaning. (Note: Use dishwasher top rack and remove before the drying cycle starts.) The Infinity Series features Aquatic’s exclusive shiatsu Back Jetting System, Aquatic Rotary Massage Jets, Full Size Pressure-Flo Hydrotherapy Jets, Rotary Massage Elite Jets and Pressure Plus Jets.
operation of Infinity series whirlpoolS jet operations (continued): • To adjust pressure (see Diagram 8B): 1. Grasp the outer ring of the jet. 2. Turn the jet clockwise to increase flow, counter-clockwise to shut off. • To remove jet (see Diagram 8C): 1. Grasp the outer ring of the jet. 2. Turn the jet counter-clockwise, until the jet clicks, then pull. • To replace or change jet (see Diagram 8C): 1. Insert the jet into jet housing. 2.
operation of Infinity series whirlpoolS jet operations (continued): Aquatic Rotary Massage Jet 10A Deeply recessed for greater bathing comfort, the Rotary Massage Jet generates a powerful rotating massage action that is directionally and pressure adjustable for custom flexibility. The Rotary Massage Jet massages the lower back and foot areas. • To adjust pressure (see Diagram 10A): 1. Grasp the outer ring of the jet. 2. Turn the outer ring clockwise to increase flow, counter-clockwise to shut off.
whirlpool user information Please note: The whirlpool action may cause even small amounts of bubble bath or shampoo to foam excessively. Exercise moderation in experimenting with different soap products. No servicing of this product should be done by the user. There are no user serviceable parts. All controls are located in the control recesses on the lip of the tub. These are the only controls that should be used by the consumer. Do not change or alter any of these controls under any circumstances.
MAINTENANCE and care INITIAL CLEANING: Before tub is used, the whirlpool system should be cleaned and disinfected. Remove all debris and clean tub before putting whirlpool into service. DO NOT USE ABRASIVE CLEANERS ON THE ACRYLIC FINISH. Use a non-abrasive detergent and rinse well after cleaning. • Fill the tub with HOT water to a level 2” above the highest jet. • Add 2 teaspoons of low-sudsing automatic dishwashing detergent and no more than 4 ounces of household bleach to the water.
MAINTENANCE and care SURFACE CLEANING: Use common household, non-abrasive cleaners for most cleaning jobs. Rinse well and dry with a clean cloth. Never use abrasive cleaners. Do not allow your Lucite® acrylic surface to come into contact with products such as acetone (nail polish remover), nail polish, dry cleaning solution, lacquer thinners, gasoline, pine oil, etc. Remove dust with a soft, dry cloth. Clean grease, oil, paint, and ink stains with isopropyl (rubbing) alcohol.
MAINTENANCE and care water quality issues (continued): Pigmented Bacteria- Water utilities from all over the United States have experienced calls from consumers inquiring and complaining about pinkish substance on bathroom fixtures that is very persistent, appearing in the shower, sink and along the water line of toilet bowls. With whirlpool bathtubs, the formation of this colored substance may be particularly pronounced in white tubs.
MAINTENANCE and care water quality issues (continued): 3. Treatment If you have contacted your water supplier and followed its instructions and you are still having problems, you need to increase the frequency of applications of low-foaming detergent/bleach starting from bi-monthly purging down to using it every other day as required to eliminate your particular problem.
troubleshooting guide warning: Always turn off power at the main electrical service panel when servicing your whirlpool. symptoms possible problems suggested solutions Motor does not start 1) GFCI or circuit breaker in OFF position. 1) 2) Fuses blown or thermal overload open. 2) 3) Locked motor shaft. 3) 4) Motor windings burned out. 4) 5) Defective starting switch inside 5) single-phase motor. 6) Disconnected or defective wiring. 6) 7) Low voltage. 7) Reset GFCI. Contact your electrician.
Replacement parts Order form for INFINITY series How To Use: 1. Find your part on the map and make note of its number & letter. 2. Using map number and letter, choose part number and select color (or finish) on parts list provided on pages 32-33. 3. Fill out the form below with the selected information. Fax or send to Aquatic. 4. Call Aquatic for parts pricing and shipping charges.
Aquatic 10f. 10e. 10. 1a. 10c. 10d. 1b. 10c. 10b. (Option) 1. (option) 9. 1c. 2a. 2. 10a. 3a. 3. 8a. 8. 6b. 6a. 8b. 4a. 4. 7. 7a. 6a. 6. infinity Series Replacement Parts Order Map 6b. 5b. 5a. 5. 6c.
Infinity Series Replacement Parts Order Map/Overview Assorted Fittings 1”, 1 1/2” or 2” Aquatic 3/4” or 1” 3/4”, 1”, 1 1/2” or 2” 1/2”, 3/4”, 1”, 1 1/2” or 2” 3/4”, 1”, 1 1/2” or 2” 1” or 1 1/2” 3/4”, 1”, 1 1/2” or 2” 29
Infinity Series Replacement Parts Order Map 12c. 22b. 22a. 13b. 23a. 14b. 24a. 25a. 26a.
Infinity Series Replacement Parts Order Map Aquatic 31
Infinity Bath Parts List Illustration No. Description part No. 32 Specify Color/ Finish/Model# 1a. Hand Held Jet--Jet 87HHJETCL --- 1b. Hand Held Jet--Hose 8115HOSECH --- 1b. Hand Held Jet--Hose 8115HOSEBR --- 1c. Hand Held Jet--Nozzles 8AII5HHJET --- 2a. Electronic Bath Side / Push Button Heater Control Panel 1111PADCL --- 3a. Air Blower Control Panel 1113PADCL --- 4a. Jet Sequencer Control Panel 1112PADCL --- 5a. 1 HP Air Blower 8000BLW --- 5b.
Infinity Bath Parts List Illustration No. Description part No. Specify Color/ Finish/Model# 16b. Grommet 4011GROMET White 16b. Grommet 4013GROMET Biscuit 16b. Grommet 4005GROMET Clear 17a. Rotary Massage Jet 87SWIRLXX* Specify Color 17b. Rotary Massage Jet Body 87ASSYWH White 17b. Rotary Massage Jet Body 87ASSYCL Clear 19a. (option) Geberit Cable Drive Waste & Overflow --- Specify Color/Model # 20a. (option) Lift and Turn Waste & Overflow 93CPDWO Chrome 20a.
Aquatic Limited Lifetime Warranty For Millennium, Infinity, Century, LuxeAir, and Luxury Series Whirlpools, Serenity Air Baths, Serenity Studio, HotSoak Series Baths and Restoration Series Limited Warranty For Original Consumer For Household Usage WHAT PRODUCTS ARE COVERED Structures and surface finishes, pumps and blowers on the Millennium, Infinity, Century, LuxeAir, Luxury, Serenity Air Baths, Serenity Studio, HotSoak, and Restoration Series.
AQUATIC Fax-On-Demand System: Toll Free (877) 618-7024 8101 E. Kaiser Blvd. • Anaheim, CA 92808 (800) 877-2005 • Fax (714) 998-5340 • www.aquaticbath.
