Instructions / Assembly

— 8 —
Customer Service: 800-945-2726
Installation Data
160304PSL/R, 160304PSML/R, 160304PSTL/R, 160304PSTML/R,
260304PSL/R, 260304PSML/R, 260304PSTL/R, 260304PSTML/R
Clean-up
CAUTION: DO NOT USE heat or solvent based cleaning
fluids. NOTE: Do not remove warranty/maintenance adhered
label. Warranty/User maintenance label must be left for
occupant (Required by ANSIZ124).
1. Prevent staining. Remove all debris before plumbing leak
test. Drain and wipe clean immediately after the inspection process.
Use sponge with warm water and liquid detergent. Rinse, drain
and wipe clean. Do not use abrasive cleansers such as scouring
powders, steel wool, metal scrapers, sandpaper or anything else
that might mar, dull or scratch
the finish. Roofing tar or paints may be removed with rubbing
alcohol or paint thinner (not lacquer thinner).
2. Plaster and latex paint may be removed with warm water, liquid
detergent and brittle brush or plastic scraper. Do not
use metal scraper or utensil to remove plaster or paint
from finish.
3. Dull areas and light scratches can be restored to high
gloss with white or cream-colored automotive rubbing compound,
followed by application of coat or good quality white automotive
polish (or similar) and buff with a soft cloth. DO NOT WAX
standing surfaces of the unit bottom (this includes textured, slip
resistant standing surfaces), which
could result in greater risk of slipping and personal injury.
4. Major gouges require professional repair.
5. See user maintenance label for more details.
User Maintenance Instructions
IMPORTANT! Use only recommended cleaners and
procedures described herein. Use of other materials and
methods may damage your bath fixture and void the
warranty.
1. For normal cleaning, never use abrasive cleaners such as scouring
powders or pads, steel wool, scrapers, sandpaper
or anything else that could scratch or dull the surface of your Aquatic
unit. Instead, use warm water and liquid detergents
or non-abrasive cleansers, especially those bathroom
cleansers recommended for fiberglass.
2. To keep your Aquatic bath fixture sparkling clean, apply a
coat of good quality automotive paste wax or polish and buff
to a high shine with a soft cloth or towel. Repeat every six
months for easier cleaning and long lasting protection. DO
NOT WAX standing surfaces of the unit bottom (this includes
textured, slip resistant standing surfaces), which could result
in greater risk of slipping and personal injury.
3. To restore a scratched or dull unit, use an automotive
polishing compound applied with a clean cotton rag. Rub
scratches and dull areas vigorously. Wipe off residues.
Follow with automotive wax treatment described above. DO
NOT WAX standing surfaces of the unit bottom (this includes
textured, slip resistant standing surfaces), which could result
in greater risk of slipping and personal injury.
4. To remove adhesive, try 3-M® natural cleaner, De-Solv-It® or
similar materials. If residues remain, saturate small white
cotton rag with nail polish remover and rub vigorously until
the adhesive dissolves and disappears. These solvents are
highly flammable and must be used sparingly and with
caution. Do not allow solvent to go down the drain. Make
sure not to contact plastic drain grates or other synthetic
materials.
5. Rubber mats: If you use rubber “anti-skid” mat, make sure to
remove it from the unit after each use to avoid harm to the
surface finish.
6. Hard Water: Water in certain regions, if not wiped up after
bathing/showering, may cause fading of some bath fixture
colors. This is a natural occurrence beyond Aquatic’s control.
(See Warranty)
CAUTION: When using any cleaning or polishing materials,
make sure to read and follow all package instructions
carefully. Wear rubber gloves at all times and avoid contact
with eyes, skin, clothing, rugs and furnishings. Make sure all
residues are rinsed off thoroughly.
LITID9034 Rev 02.15.17