Specification

ManualsBrandsAQUOR ManualsPlumbing1/2 in. NPT inlet and 3/4 in. Hose Connector 2 in. House Hydrant V1+ Modern Outdoor Wall Faucet

www.aquorwatersystems.com

(800) 458-1749

Aquor

House Hydrant V1+

ASSE 1019C / ASME A112.18.1 / CSA B125.1 / AS/NZS3718 CERTIFIED

Aquor House Hydrant V1+

The Aquor House Hydrant is a ﬂush-mounted

hydrant with twist-lock connection system designed

for outdoor use.

The hydrant is intended to be installed in the exterior

walls of homes and buildings. Upon disconnection, a

small amount of water self-drains from the outlet. The

Aquor

hose connector has a built-in vacuum breaker

for code approved anti-siphon protection.

INCLUDED IN THIS KIT

x1 Stainless Steel Hydrant

x1 Hose Connector (CN-VB2)

x1 Debris Cover

x3 #10 1.5" Mounting Screws

OVERVIEW

Overview

Read this entire instruction sheet before installing to ensure proper

installation. The information in this manual is subject to change

without notice.

Hydrant can only provide freeze protection when disconnected and

allowed to drain.

Intended for irrigation use and outdoor watering. Shall not be

subjected to more than (12) hours of continuous water pressure as

directed by ASSE code requirements.

Installation shall be in accordance with AS/NZS 3500 series of

standards.

Installation must comply with local codes and ordinances.

Please leave this manual with the property owner after completing the

hydrant installation.

FEATURES & BENEFITS

• Instant water access in less than a second,

even under full water pressure.

• Hydrant automatically self-drains upon

disconnection to provide freeze protection.

• Stainless steel operating rod and pressure

closed valve provide zero-maintenance

reliability for years.

• Robust O-ring connection system ensures a

reliable leak-proof seal, even at high water

pressures.

• Low-proﬁle design sits ﬂush against wall.

• Hydrant comes standard with ” NPT (f) inlet.

Optional rotatable 90° elbow inlets available.

• Attach any ” accessory (e.g. water timers,

splitters, regulators) to end of hose connector.

• Hose connector contains vacuum breaker for

code approved anti-siphon protection.

Summary of content (14 pages)

PAGE 1
Aquor House Hydrant V1+ OVERVIEW ® 3 ASSE 1019C / ASME A112.18.1 / CSA B125.1 / AS/NZS3718 CERTIFIED Overview Aquor House Hydrant V1+ The Aquor House Hydrant is a flush-mounted hydrant with twist-lock connection system designed for outdoor use. The hydrant is intended to be installed in the exterior walls of homes and buildings. Upon disconnection, a small amount of water self-drains from the outlet. The Aquor hose connector has a built-in vacuum breaker for code approved anti-siphon protection.
PAGE 2
Aquor House Hydrant V1+ ® INSTALLATION 5 ASSE 1019C / ASME A112.18.1 / CSA B125.1 / AS/NZS3718 CERTIFIED Installation Determine the location for the hydrant. The hydrant’s inlet must be installed into a heated area of the structure that will not drop below freezing. Before installation, make sure there is adequate work room for securing the hydrant to the supply line. 1. P R E PA R E WALL Prepare the mounting surface and entry hole.
PAGE 3
Aquor House Hydrant V1+ ® INSTALLATION 7 ASSE 1019C / ASME A112.18.1 / CSA B125.1 / AS/NZS3718 CERTIFIED With the cover wedge behind the faceplate flange secure the hydrant to the wall. x3 #10 1.5" stainless steel screws are provided. With the appropriate fitting installed, re-attach the inlet to the hydrant body. Cover wedge behind faceplate Tip: Drilling into brick or stone? Consider using specialized fasteners and/or anchors.
PAGE 4
Aquor House Hydrant V1+ INSTALLATION & OPERATION ® 9 ASSE 1019C / ASME A112.18.1 / CSA B125.1 / AS/NZS3718 CERTIFIED Depending on the type of plumbing, it will vary how the hydrant connects. Common ways of connecting to copper plumbing include soldering and push-fit adapters. Tip: With copper plumbing, consider securing the hydrant's inlet against a stud. This way the hydrant can be removed from the building's exterior if ever needed.
PAGE 5
Aquor House Hydrant V1+ ® OPERATION 11 ASSE 1019C / ASME A112.18.1 / CSA B125.1 / AS/NZS3718 CERTIFIED Connect: Line up the three helical grooves on the hose connector with the three nibs on the hydrant faceplate. Simultaneously push and twist the connector clockwise in a smooth motion. Make sure to align the grooves fully and push in before twisting. Water flow will start instantly when the connector is engaged (see image below).
PAGE 6
Aquor House Hydrant V1+ ® MAINTENANCE 13 ASSE 1019C / ASME A112.18.1 / CSA B125.1 / AS/NZS3718 CERTIFIED Maintenance Aquor ® hydrants leave the factory fully tested and operational. They are treated with an FDA approved lubricant where needed. The hydrant requires no scheduled maintenance to provide a long operational life. If a problem does arise, all the serviceable components are offered in repair kits.
PAGE 7
Aquor House Hydrant V1+ PARTS DESCRIPTION 15 ® ASSE 1019C / ASME A112.18.1 / CSA B125.1 / AS/NZS3718 CERTIFIED 9 8 7 A 1 2 3 4 10 5 6 B 11 12 Parts Description Hydrant A 1. Rear Valve Housing (inlet) 2. Valve Return Spring 3. Hydrant Body O-Ring 4. Main Valve O-Ring 5. Operating Rod 6. Hydrant Body Debris Cover 7. Debris Cover Gasket 8. Debris Cover Wedge 9. Debris Cover Nut & Bolt 10. Debris Cover B Hose Connector 11. Connector O-Rings 12.
PAGE 8
Aquor House Hydrant V1+ TECHNICAL SPECS 17 ® ASSE 1019C / ASME A112.18.1 / CSA B125.1 / AS/NZS3718 CERTIFIED Technical Specs In the Box Hydrant, Debris Cover, Hose Connector, x3 #10 Mounting Screws, Install Instructions Backflow Protection Yes, built-in vacuum breaker Inlet x Outlet 1/2 “ NPT (f) x 3/4” GHT (m) Operating Temperature 33 -140 °F Operating Water Pressure 25-125 PSI Flow Rate 6.
PAGE 9
Aquor House Hydrant V1+ TECHNICAL SPECS 19 ® ASSE 1019C / ASME A112.18.1 / CSA B125.1 / AS/NZS3718 CERTIFIED HHP002 HHP004 Close-Couple House Hydrant V1+ 4" House Hydrant V1+ STEM LENGTH: 2" OVERALL LENGTH: 3 - 5/8" STEM LENGTH: 4" OVERALL LENGTH: 5 - 3/4" www.aquorwatersystems.
PAGE 10
Aquor House Hydrant V1+ TECHNICAL SPECS 21 ® ASSE 1019C / ASME A112.18.1 / CSA B125.1 / AS/NZS3718 CERTIFIED HHP006 HHP008 6" House Hydrant V1+ 8" House Hydrant V1+ STEM LENGTH: 6" OVERALL LENGTH: 7 - 3/4" STEM LENGTH: 8" OVERALL LENGTH: 9 - 3/4" www.aquorwatersystems.
PAGE 11
Aquor House Hydrant V1+ TECHNICAL SPECS 23 ® ASSE 1019C / ASME A112.18.1 / CSA B125.1 / AS/NZS3718 CERTIFIED HHP010 HHP012 10" House Hydrant V1+ 12" House Hydrant V1+ STEM LENGTH: 10" OVERALL LENGTH: 11 - 3/4" STEM LENGTH: 12" OVERALL LENGTH: 13 - 3/4" www.aquorwatersystems.
PAGE 12
Aquor House Hydrant V1+ TROUBLESHOOTING 25 ® ASSE 1019C / ASME A112.18.1 / CSA B125.1 / AS/NZS3718 CERTIFIED Troubleshooting PROBLEM SOLUTION No water flow when connected. First you’ll want to identify whether the issue is in the hydrant of the hose connector. Make sure water supply is live to the hydrant. Try depressing the hydrant valve with your thumb to test for pressure. If the water pressure is live, the issue is likely the hose connector.
PAGE 13
Aquor House Hydrant V1+ TROUBLESHOOTING 27 ® ASSE 1019C / ASME A112.18.1 / CSA B125.1 / AS/NZS3718 CERTIFIED PROBLEM SOLUTION Water leaking from the hydrant main outlet (front) when connected. Inspect hose connector O-rings for damage, replace or lubricate if needed. Water leaking from the hydrant main outlet when disconnected. A slow leak may indicate a stuck or bent internal rod, or damaged O-ring. First, try to reset the valve from the front.
PAGE 14
Aquor House Hydrant V1+ ® TROUBLESHOOTING, WARRANTY, & CONTACT 29 ASSE 1019C / ASME A112.18.1 / CSA B125.1 / AS/NZS3718 CERTIFIED PROBLEM SOLUTION Hose connector is difficult to connect or disconnect. Try squeezing your hose nozzle while simultaneously disconnecting. If left outdoors in variable weather, water expansion may have caused the connector’s internal check-valve to seize. Try disassembling or removing the connector’s check valve. Test with a different hose connector.