WAVE 2 AC WIRELESS ACCESS POINT Quick Start Guide AN-530-AP-I-AC
Araknis Networks Wireless Access Point Quick Start Guide Regulatory Compliance & Safety Information for Model AN-530-AP-I-AC Electrical Safety Advisory Sécurité électrique consultatif Important Safety Instructions Consignes de sécurité importantes Read the safety instructions before using this product. Lisez les consignes de sécurité avant d'utiliser ce produit. 2 1. Read these instructions. Lisez ces instructions. 2. Keep these instructions. Conservez ces instructions. 3. Heed all warnings.
Araknis Networks Wireless Access Point Quick Start Guide 5. Do not use this apparatus near water. Ne pas utiliser cet appareil près de l'eau. 6. Clean only with dry cloth. Nettoyez-le uniquement avec un chiffon sec. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Ne pas bloquer les ouvertures de ventilation. Installer conformément aux instructions du fabricant. 8.
Araknis Networks Wireless Access Point Quick Start Guide 11. Only use attachments/accessories specified by the manufacturer. Utilisez uniquement des fixations / accessoires spécifiés par le fabricant. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
Araknis Networks Wireless Access Point Quick Start Guide généralement transitoires qui sont très destructives envers les équipements terminaux connectés à des sources d'alimentation CA. La garantie de cet appareil ne couvre pas les dommages causés par les surtensions électriques ou transitoires de foudre. Pour réduire le risque de cet équipement devient endommagé, il est suggéré que le client envisager l'installation d'un limiteur de surtension. 16.
Araknis Networks Wireless Access Point Quick Start Guide N'introduisez jamais d'objets d'aucune sorte dans ce produit à travers les fentes du boîtier car ils pourraient toucher des points de tension dangereux ou court-circuiter des pièces qui pourraient entraîner un incendie ou un choc électrique. 20. This product can interfere with electrical equipment such as tape recorders, TV sets, radios, computers and microwave ovens if placed in close proximity.
Araknis Networks Wireless Access Point Quick Start Guide The lightning flash and arrow head within the triangle is a warning sign alerting you of dangerous voltage inside the product L’éclair et la flèche dans le triangle est un signe d’alerte pour vous avertir d’une tension dangereuse à l’intérieur du produit. Caution: To reduce the risk of electric shock, do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualified service personnel.
Araknis Networks Wireless Access Point Quick Start Guide Warning!: To reduce the risk of electrical shock, do not expose this apparatus to rain or moisture. AVERTISSEMENT! Pour réduire le risque de choc électrique, n'exposez pas cet appareil à la pluie ou à l'humidité. Save these instructions. Conservez ces instructions. 8 The AN-530-AP-I-AC uses the following power inputs: DC IN: 12V⎓, 2A PoE+ IN: 48V⎓, 0.53A Support: 866.838.
Araknis Networks Wireless Access Point Quick Start Guide © 2020 Araknis Networks® 9
Araknis Networks Wireless Access Point Quick Start Guide USA & Canada Compliance FCC Part 15, Subpart B & IC Unintentional Emissions Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation.
Araknis Networks Wireless Access Point Quick Start Guide IMPORTANT! Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. IMPORTANT! Tous les changements ou modifications pas expressément approuvés par la partie responsable de la conformité ont pu vider l’autorité de l’utilisateur pour actionner cet équipement.
Araknis Networks Wireless Access Point Quick Start Guide This equipment must be installed by qualified professionals or contractors in accordance with FCC Part 15.203 & IC RSS-247, Antenna Requirements. Do not use any antenna other than the one provided with the unit. Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
Araknis Networks Wireless Access Point Quick Start Guide (iii) De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.
Araknis Networks Wireless Access Point Quick Start Guide and your body or nearby persons. Déclaration d'exposition aux radiations RF Cet équipement est conforme aux limites d'exposition aux rayonnements RF et IC de la FCC définies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec une distance minimale de 20 centimètres entre le radiateur et votre corps ou des personnes proches.
Araknis Networks Wireless Access Point Quick Start Guide EU candidate countries without any restriction. AT BE BG HR CY CZ DK EE FI FR DE EL HU IE IT LV LT LU MT NL PL PT RO SK SI ES SE UK The frequency and maximum transmitted power in EU are listed as below: AN-530-AP-I-AC 2412 - 2472 MHz: 17dBm 5180 - 5240 MHz: 18.5dBm Operations in the 5.15-5.35GHz band are restricted to indoor usage only.
Araknis Networks Wireless Access Point Quick Start Guide Welcome to Araknis Networks™ Thank you for choosing an Araknis™ Tri-Band Mesh Enabled Wireless Access Point (WAP). With improved thermal performance by way of a die-cast aluminum bottom and a tried and true mounting system, this tri-band mesh enabled access point has the versatility to maintain performance in both wireless and wired installs for home and commercial applications.
Araknis Networks Wireless Access Point Quick Start Guide Step 1: Unbox Wireless Access Point Mounting Bracket Tile Ceiling Backing Plate Quick Start Guide Tile Ceiling Mounting Hardware Drywall Mounting Hardware Wood Surface Mounting Hardware (WAP)* Male-to-Female Category Jumper Cable © 2020 Araknis Networks® 17
Araknis Networks Wireless Access Point Quick Start Guide Step 2: Install A Ceiling Mount B Shelf Mount C In-Ceiling Mount D Wall Mount Accessory not included NOTE: Use the ceiling back plate on top of acoustic ceiling tiles to prevent the mounting nuts from pulling through. 18 Support: 866.838.
Araknis Networks Wireless Access Point Quick Start Guide Position the Ceiling Mount Tile Ceiling Backing Plate Ceiling Tiles Ceiling Mount WAP Center Line* Center Line* Position 2 Position 1 First Position Second Position * Center line of the bracket is not necessarily the center line of the WAP when installed. Please use the guide above to understand the center line of the WAP when installing the bracket.
Araknis Networks Wireless Access Point Quick Start Guide Step 3: Connect LAN WAN AN-310-SW-F-8-POE Internet Router PoE Switch WAP POWER + DATA (OUT) LAN AN-ACC-INJ-30W WAN DC 48V Input Power DATA (IN) AN-310-SW-F-8-POE Internet Router LAN Switch PoE Injector (not included) WAP WAP DC Power Supply (not included) WAN AN-310-SW-F-8-POE Internet 20 Router Switch Support: 866.838.
Araknis Networks Wireless Access Point Quick Start Guide Step 4: Verify LED* LED* *NOTE: The LED is located on the side of the device. LED Status: • Blinking White: Powering on. • Solid White: Ready for setup. • Solid Blue: Controller/Node connected to Internet. • Blinking/Solid Red: Wireless backhaul lost or unit locked up. For a full list of LED behaviors, please see link.
Araknis Networks Wireless Access Point Quick Start Guide Step 5: Log Into Web Interface A Log in using the default credentials: Username araknis Password araknis NOTE: If you can’t connect to the WAP using this method, or need to configure the device before connecting it to the network, try these options for accessing your device: 22 • DHCP IP address – Page 15 • Default IP Address – Page 16 • OvrC – Page 19 Support: 866.838.
Araknis Networks Wireless Access Point Quick Start Guide Pro Tip: Save and Apply Changes After making changes to settings on a menu page, click the “Save” button on the menu to hold the new settings in the Apply Changes field. After all desired changes have been made, click “Apply Changes” to review the new settings if any. Click "Apply" to make the changes or "Revert" to cancel the changes. NOTE: Settings will take affect after the progress bar completes 100%.
Araknis Networks Wireless Access Point Quick Start Guide Other Access Methods: DHCP IP Address The WAP is configured to DHCP by default so that the DHCP server can assign an IP address when the WAP is connected to the network (the DHCP server is usually the router). This address can be used for accessing the web interface. Check the client table on your router to find the IP address of the WAP. 24 Support: 866.838.
Araknis Networks Wireless Access Point Quick Start Guide Other Access Methods: Default IP Address If the WAP is not issued an IP address on the network, or needs to be accessed while not connected to a network, you can configure your computer's network connection to allow access using the default IP address, “192.168.20.253”. Windows 7 screenshots shown for reference. A Connect your PC to the WAP using a network patch cable.
Araknis Networks Wireless Access Point Quick Start Guide Other Access Methods: Default IP Address Windows 7 screenshots shown for reference. D In the left bar, left-click “Change adapter settings”. 26 E Right-click the icon for the wired network connection and left-click "Properties". F Left-click to highlight “Internet Protocol Version 4 (TCP/IPv4), then left-click “Properties”. Support: 866.838.
Araknis Networks Wireless Access Point Quick Start Guide Other Access Methods: Default IP Address Windows 7 screenshots shown for reference. G In the “General” tab, left-click "Use the following IP address:" and enter the IP address and subnet mask. IP Address 192.168.20.2 Subnet Mask 255.255.255.0 © 2020 Araknis Networks® H Left-click “OK” to close Internet Protocol Version 4 (TCP/IPv4) Properties, then left-click "OK" to close wireless network connection properties.
Araknis Networks Wireless Access Point Quick Start Guide Other Access Methods: OvrC OvrC gives you remote device management, real-time notifications, and intuitive customer management, right from your computer or mobile device. Setup is plug-and-play, with no port forwarding or DDNS address required. To add this device to your OvrC account: A Connect the WAP to the Internet B Log Into OvrC (www.ovrc.
Contacting Technical Support P (866) 838-5052 E techsupport@snapav.com 2-Year Limited Warranty Find details of this product's 2-Year Limited Warranty at snapav.com/warranty, or request a paper copy from Customer Service at (866) 424-4489. Find other legal resources, such as regulatory notices and patent information, at snapav. com/legal. US local representative information: Company: Wirepath Home Systems LLC Address: 1800 Continental Blvd. Suite 200, Charlotte, NC 28273 USA Tel: 704.927.