V487 WIRELESS MODEM UNIT User’s Guide An Arcadian Networks Inc.
V487i WMU User’s Guide Copyright and Trademark Information: © 2008 Arcadian Networks Inc. All rights reserved. Arcadian Networks Inc. reserves the right to alter the equipment specifications and descriptions in this publication without prior notice. No part of this publication shall be deemed part of any contract or warranty unless specifically incorporated by reference into such contract or warranty.
V487i WMU User’s Guide FCC COMPLIANCE STATEMENT NOTE: This equipment is authorized under FCC ID:V72AE11 to operate in the A Block (re-banding) of the Upper 700 MHz Band pursuant to Part 27 of the FCC’s rules. In addition, this equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
V487i WMU User’s Guide Installation and Safety Information The following information is provided to ensure safe operation of this equipment. Arcadian Networks assumes no liability in the event that the customer fails to comply with the following safety precautions and warnings. DC System Power-on 1- When connecting the DC power lines, make sure to connect the Ground line first. 2- When disconnecting the DC power lines, make sure to disconnect Ground last.
V487i WMU User’s Guide Safety Summary Warnings: Carefully connect units to the supply circuit so that wiring is not overloaded. Connect the Ground first (and remove Ground last when disconnecting). Read the installation instructions before connecting the system to its power source. Secure all power cabling when installing this unit. Do not touch the power supply when the power cord is connected.
V487i WMU User’s Guide CONTENTS 1 1.1 1.2 1.3 1.4 Overview and Purpose .................................................. 7 Purpose of This User’s Guide .......................................... 7 Target Audience............................................................... 7 Document Conventions.................................................... 8 Arcadian Networks ........................................................... 8 2 Modem Features and Components .............................. 9 2.
V487i WMU User’s Guide 1 OVERVIEW AND PURPOSE Welcome to the User’s Guide for the Arcadian Networks Inc. V487 Modem. Figure 1-1: The Arcadian Networks V487 Wireless Modem Unit 1.1 Purpose of This User’s Guide This guide is designed to be used as a tool in the initial installation and periodic maintenance of the V487. It contains information on how to perform the following tasks: 1.
V487i WMU User’s Guide 1.3 Document Conventions This guide is intended for service personnel required to install, configure or maintain the V487 modem. The following icons appear throughout this guide: Note: This is a note. It provides additional information on the current topic. Warning: This is a warning. It contains cautionary information on the current topic. Tip: This is a tip. It provides time saving information to the reader. 1.4 Arcadian Networks Arcadian Networks Inc.
V487i WMU User’s Guide 2 MODEM FEATURES AND COMPONENTS The V487 modem offers the following features: • Point-to-multipoint broadband wireless Internet access • Superior operations over a wide range of modulation formats and IF bandwidths, including noisy channels • Easy installation • Robust RF performance • Internal radio for UHF bands 2.1 Right Panel Connectors There are two connectors located on the right panel of the V487 modem.
V487i WMU User’s Guide 2.2 Left Panel Connectors There are two connectors located on the left panel of the V487 modem. RF Link Power Figure 2-2: V487 WMU Left side Panel Connectors Connector Function POWER Connect 9.5V to 29 V external power source here. Antenna Connect this N-type connector to the UHF antenna.
V487i WMU User’s Guide 3 USING THE MODEM Follow the steps below to use the modem properly. To use the modem: 1 Check that the computer with which you are using the V487 modem contains a working Ethernet network card, and has the following software installed and operational: • Microsoft Windows 95 operating system or later • A standard Internet browser application • The Telnet communications utility 2 Attach your computer to the modem’s LAN port with the included RJ-45 Ethernet cable.
V487i WMU User’s Guide 4 TECHNICAL SPECIFICATIONS General Dimensions Operating Temperature Power 12.6 x 7.9 x 4.4 in. (32 x 20 x 11 cm) -33 to 60° C 9.5V-29V (Max 3A) Interface Data Interface RF Interface RS232 (SCADA service)RJ45 – 10/100 baseT Ethernet full/half duplex 50 ohm N Type Female Connector RF Characteristics Downstream RX Frequency Channel Bandwidth Modulation Format Data Rates Rx Sensitivity (dBm) 757 – 758 MHz Downstream Receive 245, 330 KHz QPSK, 16QAM, & 64QAM 0.55 – 1.
V487i WMU User’s Guide Service Network Management Security IP Protocols # IP Data Services Protocol: MIB: Provisioning: Link Layer Encryption: Key Distribution: Network Protocols: Transport Protocols: Application Protocols: 64 CPE MAC Addresses - 13 - SNMP RFC1213, RFC1493, RFC2233, RFC2669, RFC2670, DOCSIS Privacy MIB As per DOCSIS DES CBC, 40 and 56 Bits per user (Sara) Two-layer key distribution protocol, which includes DES-ECB and RSA public key encryption and HMAC-SHA1 authorization IP, ICMP, AR
V487i WMU User’s Guide 5 PROBLEM TROUBLESHOOTING If you encounter problems with your modem, try the following steps. 1 Check for damage to the external modem casing during shipping or installation. If you see visible damage, the modem may need replacement. 2 Verify that the 9.5Volt to 29V modem power supply jack is connected to the modem POWER connector on the Left side of the modem, and that the modem power supply is connected to a known-good AC power outlet.
V487i WMU User’s Guide # Problem Description Possible Cause Potential Resolutions 2 The LAN LED does not light up. • The connection between the modem and the PC may be faulty. 1. Check the 10/100BaseT cable connection. 2. Check the network configuration: IP address, Gateway, DHCP, and DNS. 3. Reset the modem by disconnecting and reconnecting the power. 4. Replace the NIC Ethernet card. 5. Test the connection using another modem or network device.
V487i WMU User’s Guide 6 WARRANTY INFORMATION The Arcadian Networks Inc. Limited Warranty and related information can be found in the terms and conditions and/or other contracts under which this product was purchased.
V487i WMU User’s Guide CONTACTING ARCADIAN NETWORKS For further information about the V487 WMU or other Arcadian Networks products, visit the Arcadian Networks Website at: www.arcadiannetworks.com .
