- A & R Cambridge Car Stereo System User Manual

CD192
E-6
English
CD192
E-7
English
Using the CR-314 remote control
NOTE: Remember to install the two AAA batteries
supplied before trying to use your remote control.
Do not place anything in front of the display area
on the CD player (where the IR receiver is located),
or the remote control may not work.
Note that greyed-out buttons on the remote control
are DVD-specic and are not used with the CD
player.
CR-314
RPT CLEAR
0
PROG
A-B
7
8
9
DISP
4
5 6
CD
DVD
1
2
3
OK
OPEN
MUTE
P
MODE
CD/DVD REMOTE
CD DVD
SUBT
ZOOM AUDIO MEM RTN
ANGLE SETUP STATUS SRCH
MENU
TITLE
CD/DVD
Ensure that CD mode is selected using the CD/DVD
toggle button. The ‘CD’ LED above the CD/DVD
button is lit briey when CD mode is selected.
DISP (display)
Turns the display on or off. Turning the display off
generally produces a slight improvement in sound
quality.
A–B
This button enables you to repeat any section of music
within a track. Whilst the disc is playing, press the A–B
button at the start of the section you wish to repeat.
‘REPEAT’ is shown on the display and the letter ‘A–’
ashes. Press the button a second time when you reach
the end of the section you wish to repeat. The ‘A–B’
letters stop ashing and remain lit. This section will
repeat until you press or or . The forward search
button ( ) moves forward within the selected loop.
RPT (repeat)
To repeat the entire CD or a pre-programmed selection
of tracks press RPT once: ‘REPEAT’ lights on the display.
To repeat a particular track, select that track and then
press RPT twice so that ‘REPEAT 1’ is shown on the
display. If you now select a different track, that track is
repeated instead.
To cancel the repeat function press RPT a third time.
CLEAR
If you make a mistake whilst programming you can
delete the last entered track by pressing CLEAR.
To delete all the programmed tracks, press CLEAR
repeatedly until ‘0’ is displayed.
To exit the program facility, press PROG.
TITLE
Press TITLE once to display the remaining time of the
currently playing track. Press again to display the time
remaining of the disc. Press a third time to turn the text
display on.
Press TITLE again and the display reverts to its original
setting, showing the time elapsed for the current track.
For CDs with text, pressing TITLE once while the disc is
loaded but not playing displays the artist’s name.
Pressing TITLE a second time displays the total number
of tracks and the total playing time.
0–9 keypad
This allows direct access to individual tracks on the disc.
To select a track, press the corresponding keypad button.
For tracks greater than 9, enter the digits in sequence.
For example, to play track 15, press and hold 1 until the
number on the display moves to the left, then press 5.
PROG (Program)
You can program a selection of up to 24 tracks from
a disc to play in any order. Select a track by using the
and buttons, then press PROG to program the
track into memory (‘PROGRAM’ appears on the display
to indicate that you have started programming a
sequence). Repeat these steps to program the remaining
tracks in your selection. Alternatively, press PROG once
and enter your track selection using the 0–9 keypad.
The display shows the track numbers programmed,
the total length of the programmed sequence and the
number of tracks programmed (shown by a number
below the word ‘STEP’).
Each time you enter a track the number below ‘STEP’
increments by one and ashes until you press PROG
to conrm. If you fail to press PROG within about ve
seconds the display stops ashing and you will have to
reselect the track.
Press to play the program. Press again to replay the
entire sequence from the start. Press and hold CLEAR to
erase the programmed sequence. Press PROG again to
exit the program facility.
MUTE
Stops sound to the speaker outputs of certain Arcam
ampliers.
Volume +/–
Adjusts the volume on Arcam remote-controllable
ampliers.
Note that the volume (+/–) controls and MUTE button
have no effect on the audio output level of the CD
players.
OPEN
Opens and closes the CD tray
Search and Skip Track
Search backwards and forwards;
Skip track backwards and forwards (see page 5)
Playback control
Pause, Play and Stop (see page 5)
P MODE
Press once to shufe play CD tracks (i.e. play them in
a random order). Press again to cancel shufe play.