Owner's Manual
Table Of Contents
- Handbook
- Factory default reset
- Safety Guidelines
- Welcome
- Contents
- Before You Begin
- Trademark Acknowledgments
- Rear Panel Connections and Controls
- Audio/Video Connections
- Connection Guide
- Radio & Wireless Audio Connectors
- Other Connectors
- Speakers
- Connecting Speakers
- Operation
- Extended front panel menu
- Front Panel Operation
- Remote Control
- Device Mode/Source keys
- Customising the Remote
- Essential Setup
- Auto Speaker Setup
- Setup Menus
- Connecting to a Network
- Decoding Modes
- Tuner Operation
- Troubleshooting
- Specifications
- Device Code Tables
- Custom Installation Notes
- Contents
- Introduction
- Set-up
- Conventions
- Serial Cable Specification
- Example command and response sequence
- System Command Specifications
- Input Command Specifications
- Output Command Specifications
- Menu Command Specifications
- Setup Adjustment Command Specifications
- Treble Equalisation (0x35)
- Bass Equalisation (0x36)
- Room Equalisation (0x37)
- Dolby Volume (0x38)
- Dolby Leveller (0x39)
- Dolby Volume Calibration Offset (0x3A)
- Balance (0x3B)
- Subwoofer Trim (0x3F)
- Lipsync Delay (0x40)
- Compression (0x41)
- Request incoming video parameters (0x42)
- Request incoming audio format (0x43)
- Request incoming audio sample rate (0x44)
- Set/Request Sub Stereo Trim (0x45)
- Set/Request Zone 1 OSD on/off (0x4E)
- Set/Request Video Output Switching (0x4F)
- Set/request input name (0x20)
- FM Scan up/down (0x23)
- DAB Scan (0x24)
- Heartbeat (0x25)
- Reboot (0x26)
- Bluetooth status (0x50)
- Setup (0x27)
- Room EQ name(s) (0x34)
- Now Playing Information (0x64)
- Input config (0x28)
- General Setup (0x29)
- Speaker Types (0x2A)
- Speaker Distances (0x2B)
- Speaker Levels (0x2C)
- Video Inputs (0x2D)
- HDMI settings (0x2E)
- Zone settings (0x2F)
- Network (0x30)
- Bluetooth (0x32)
- Engineering menu (0x33)
- AV RC5 command codes
- Product Info
- Mandatory Software Update
- Software Release Notes
- Warranty & Product Registration
EN
EN-15
Speakers
The AVR10/AVR20/AVR30/AV40 allows you to connect
up to sixteen speakers. The AV40 needs additional power
amplifiers for all channels. The AVR10/AVR20/AVR30 has
7 channels of amplification. 5 channels of amplification
correspond to speakers installed in the front left, centre, front
right, surround left, surround right. The remaining 2 channels
of amplification can be assigned as:
bi-amp the front left and right
surround back left and surround back right
height 1 left and right
Zone 2 left and right
Height front left, height front right, height back left, height
back right and five more additional speakers can be attached
using an additional power amplifier, see page EN-16 for more
information.
With the addition of correctly installed and configured
height channels, Dolby Atmos for the home, DTS:X or Auro
3D brings the ultimate cinema sound experience to your
home theatre to create powerful, moving audio that flows
around you.
The conguration and placement of your speakers
is very important. All speakers, with the exception of
the subwoofer(s), should be arranged around your normal
viewing/listening position. The subwoofer should be placed
in a position which gives an even frequency response in all
listening positions. Incorrect placement leads to bass boom
in some areas. Often the only way to find a good position
for your subwoofer(s) is by experimentation. A good place
to start experimenting is close to a wall but at least 1m
away from any corners. You can also consult your subwoofer
handbook for placement suggestions.