Owner's Manual
Table Of Contents
- Handbook
- Factory default reset
- Safety Guidelines
- Welcome
- Contents
- Before You Begin
- Trademark Acknowledgments
- Rear Panel Connections and Controls
- Audio/Video Connections
- Connection Guide
- Radio & Wireless Audio Connectors
- Other Connectors
- Speakers
- Connecting Speakers
- Operation
- Extended front panel menu
- Front Panel Operation
- Remote Control
- Device Mode/Source keys
- Customising the Remote
- Essential Setup
- Auto Speaker Setup
- Setup Menus
- Connecting to a Network
- Decoding Modes
- Tuner Operation
- Troubleshooting
- Specifications
- Device Code Tables
- Custom Installation Notes
- Contents
- Introduction
- Set-up
- Conventions
- Serial Cable Specification
- Example command and response sequence
- System Command Specifications
- Input Command Specifications
- Output Command Specifications
- Menu Command Specifications
- Setup Adjustment Command Specifications
- Treble Equalisation (0x35)
- Bass Equalisation (0x36)
- Room Equalisation (0x37)
- Dolby Volume (0x38)
- Dolby Leveller (0x39)
- Dolby Volume Calibration Offset (0x3A)
- Balance (0x3B)
- Subwoofer Trim (0x3F)
- Lipsync Delay (0x40)
- Compression (0x41)
- Request incoming video parameters (0x42)
- Request incoming audio format (0x43)
- Request incoming audio sample rate (0x44)
- Set/Request Sub Stereo Trim (0x45)
- Set/Request Zone 1 OSD on/off (0x4E)
- Set/Request Video Output Switching (0x4F)
- Set/request input name (0x20)
- FM Scan up/down (0x23)
- DAB Scan (0x24)
- Heartbeat (0x25)
- Reboot (0x26)
- Bluetooth status (0x50)
- Setup (0x27)
- Room EQ name(s) (0x34)
- Now Playing Information (0x64)
- Input config (0x28)
- General Setup (0x29)
- Speaker Types (0x2A)
- Speaker Distances (0x2B)
- Speaker Levels (0x2C)
- Video Inputs (0x2D)
- HDMI settings (0x2E)
- Zone settings (0x2F)
- Network (0x30)
- Bluetooth (0x32)
- Engineering menu (0x33)
- AV RC5 command codes
- Product Info
- Mandatory Software Update
- Software Release Notes
- Warranty & Product Registration
EN
EN-27
2
Toggles power between standby and on.
1
Open/close disc tray.
0...9
Searches for and plays the track corresponding
to the key pressed.
DISP
Cycles through the front panel
display’s brightness options.
MODE
Cycles through the repeat options (track, disc,
etc.).
7
Fast rewind.
8
Fast forward.
9
Press and release to skip back to the beginning
of the current/previous track
:
Press and release to skip forwards to the
beginning of the next track.
Stop playback of a CD
4;
Pause and playback of the current track.
POP UP
In ‘normal play’ (i.e. the display does not show
the letter P), press the
'
and
,
keys to
select the track and then stores the track.
In ‘program play’ mode, the key deletes
the stored track.
Navigate setup and CD programme selection
menus.
OK selects the highlighted file or enters the
highlighted menu on the screen – equivalent
to ‘Enter’ or ‘Select’ on some remote controls.
'
Up
<
Left
>
Right
,
Down
CD +
'
Power on from Standby
CD +
,
Standby from Power on.
AMP
Resets remote to AMP mode.
RADIO
Plays the programmed tracks.
CD Device Mode
The Device Mode button selects as the source.
The button is configured to control the CD functions of
Arcam CD players, although this can be changed (see
“Locking/Unlocking a specific Device Mode” on page EN-23).