Owner's Manual
Table Of Contents
- Handbook
- Factory default reset
- Safety Guidelines
- Welcome
- Contents
- Before You Begin
- Trademark Acknowledgments
- Rear Panel Connections and Controls
- Audio/Video Connections
- Connection Guide
- Radio & Wireless Audio Connectors
- Other Connectors
- Speakers
- Connecting Speakers
- Operation
- Extended front panel menu
- Front Panel Operation
- Remote Control
- Device Mode/Source keys
- Customising the Remote
- Essential Setup
- Auto Speaker Setup
- Setup Menus
- Connecting to a Network
- Decoding Modes
- Tuner Operation
- Troubleshooting
- Specifications
- Device Code Tables
- Custom Installation Notes
- Contents
- Introduction
- Set-up
- Conventions
- Serial Cable Specification
- Example command and response sequence
- System Command Specifications
- Input Command Specifications
- Output Command Specifications
- Menu Command Specifications
- Setup Adjustment Command Specifications
- Treble Equalisation (0x35)
- Bass Equalisation (0x36)
- Room Equalisation (0x37)
- Dolby Volume (0x38)
- Dolby Leveller (0x39)
- Dolby Volume Calibration Offset (0x3A)
- Balance (0x3B)
- Subwoofer Trim (0x3F)
- Lipsync Delay (0x40)
- Compression (0x41)
- Request incoming video parameters (0x42)
- Request incoming audio format (0x43)
- Request incoming audio sample rate (0x44)
- Set/Request Sub Stereo Trim (0x45)
- Set/Request Zone 1 OSD on/off (0x4E)
- Set/Request Video Output Switching (0x4F)
- Set/request input name (0x20)
- FM Scan up/down (0x23)
- DAB Scan (0x24)
- Heartbeat (0x25)
- Reboot (0x26)
- Bluetooth status (0x50)
- Setup (0x27)
- Room EQ name(s) (0x34)
- Now Playing Information (0x64)
- Input config (0x28)
- General Setup (0x29)
- Speaker Types (0x2A)
- Speaker Distances (0x2B)
- Speaker Levels (0x2C)
- Video Inputs (0x2D)
- HDMI settings (0x2E)
- Zone settings (0x2F)
- Network (0x30)
- Bluetooth (0x32)
- Engineering menu (0x33)
- AV RC5 command codes
- Product Info
- Mandatory Software Update
- Software Release Notes
- Warranty & Product Registration
13
Request Video Output Resolution (0x13)
Request the Video Output Resolution of zone 1.
Example
Command/response sequence to request the video output in zone 1 where the
resolution is 1080p:
Command: 0x21 0x01 0x13 0x01 0xF0 0x0D
Response: 0x21 0x01 0x13 0x00 0x01 0x05 0x0D
COMMAND:
Byte: Description:
St 0x21
Zn 0x01
Cc 0x13
Dl 0x01
Data 0xF0 – Request the video output.
Et 0x0D
RESPONSE:
Byte: Description:
St 0x21
Zn 0x01
Cc 0x13
Ac Answer code
Dl 0x01
Data 0x02 – SD Progressive.
0x03 – 720p.
0x04 – 1080i.
0x05 – 1080p
0x06 – ‘Preferred’
0x07 – Bypass
0x08 - 4k
0x09 - 8k
Et 0x0D
Request RDS information (0x12)
Request RDS information from the current radio station in a given zone. If FM
is not selected on the given zone an error 0x85 is returned.
Example
Command/response sequence to request the RDS information on FM in zone
1, where the response is “Playing your favourite music”.
Command: 0x21 0x01 0x12 0x01 0xF0 0x0D
Response: 0x21 0x01 0x12 0x00 0x1C 0x00 0x50 0x6C 0x61 0x79
0x69 0x6E 0x67 0x20 0x79 0x6F 0x75 0x72 0x20 0x66
0x61 0x76 0x6F 0x75 0x72 0x69 0x74 0x65 0x20 0x6D
0x75 0x73 0x69 0x63 0x0D
COMMAND:
Byte: Description:
St 0x21
Zn Zone number
Cc 0x12
Dl 0x01
Data1 Request information source:
0xF0 – FM
Et 0x0D
RESPONSE:
Byte: Description:
St 0x21
Zn Zone number
Cc 0x12
Ac Answer code
Dl Data length <n>
Data1 –
Data<n>
The radio programme type in ASCII characters
Et 0x0D