Owner's Manual
Table Of Contents
- Handbook
- Factory default reset
- Safety Guidelines
- Welcome
- Contents
- Before You Begin
- Trademark Acknowledgments
- Rear Panel Connections and Controls
- Audio/Video Connections
- Connection Guide
- Radio & Wireless Audio Connectors
- Other Connectors
- Speakers
- Connecting Speakers
- Operation
- Extended front panel menu
- Front Panel Operation
- Remote Control
- Device Mode/Source keys
- Customising the Remote
- Essential Setup
- Auto Speaker Setup
- Setup Menus
- Connecting to a Network
- Decoding Modes
- Tuner Operation
- Troubleshooting
- Specifications
- Device Code Tables
- Custom Installation Notes
- Contents
- Introduction
- Set-up
- Conventions
- Serial Cable Specification
- Example command and response sequence
- System Command Specifications
- Input Command Specifications
- Output Command Specifications
- Menu Command Specifications
- Setup Adjustment Command Specifications
- Treble Equalisation (0x35)
- Bass Equalisation (0x36)
- Room Equalisation (0x37)
- Dolby Volume (0x38)
- Dolby Leveller (0x39)
- Dolby Volume Calibration Offset (0x3A)
- Balance (0x3B)
- Subwoofer Trim (0x3F)
- Lipsync Delay (0x40)
- Compression (0x41)
- Request incoming video parameters (0x42)
- Request incoming audio format (0x43)
- Request incoming audio sample rate (0x44)
- Set/Request Sub Stereo Trim (0x45)
- Set/Request Zone 1 OSD on/off (0x4E)
- Set/Request Video Output Switching (0x4F)
- Set/request input name (0x20)
- FM Scan up/down (0x23)
- DAB Scan (0x24)
- Heartbeat (0x25)
- Reboot (0x26)
- Bluetooth status (0x50)
- Setup (0x27)
- Room EQ name(s) (0x34)
- Now Playing Information (0x64)
- Input config (0x28)
- General Setup (0x29)
- Speaker Types (0x2A)
- Speaker Distances (0x2B)
- Speaker Levels (0x2C)
- Video Inputs (0x2D)
- HDMI settings (0x2E)
- Zone settings (0x2F)
- Network (0x30)
- Bluetooth (0x32)
- Engineering menu (0x33)
- AV RC5 command codes
- Product Info
- Mandatory Software Update
- Software Release Notes
- Warranty & Product Registration
17
Setup Adjustment Command Specifications
Treble Equalisation (0x35)
Adjust the amount of treble equalisation.
Example
Command/response sequence to set the treble to -2dB:
Command: 0x21 0x01 0x35 0x01 0x82 0x0D
Response: 0x21 0x01 0x35 0x00 0x01 0x82 0x0D
Bass Equalisation (0x36)
Adjust the amount of bass equalisation.
Example
Command/response sequence to increase the bass EQ by 1dB when it was 0dB:
Command: 0x21 0x01 0x36 0x01 0xF1 0x0D
Response: 0x21 0x01 0x36 0x00 0x01 0x01 0x0D
Room Equalisation (0x37)
Turn the room equalisation system on/o.
Example
Command/response sequence to turn the room equalisation system on (EQ1):
Command: 0x21 0x01 0x37 0x01 0x01 0x0D
Response: 0x21 0x01 0x37 0x00 0x01 0x01 0x0D
COMMAND:
Byte: Description:
St 0x21
Zn Zone number
Cc 0x35
Dl 0x01
Data 0x00 — 0x0C – Set treble to 0dB — +12dB
0x81 — 0x8C – Set treble to -1dB — -12dB
0xF0 – Request current treble value
0xF1 – Increment treble by 1dB
0xF2 – Decrement treble by 1dB
Et 0x0D
RESPONSE:
Byte: Description:
St 0x21
Zn Zone number
Cc 0x35
Ac Answer code
Dl 0x01
Data1 0x00 — 0x0C – Treble is 0dB — +12dB
0x81 — 0x8C – Treble is -1dB — -12dB
Et 0x0D
COMMAND:
Byte: Description:
St 0x21
Zn Zone number
Cc 0x36
Dl 0x01
Data 0x00 — 0x0C – Set bass to 0dB — +12dB
0x81 — 0x8C – Set bass to -1dB — -12dB
0xF0 – Request current bass value
0xF1 – Increment bass by 1dB
0xF2 – Decrement bass by 1dB
Et 0x0D
RESPONSE:
Byte: Description:
St 0x21
Zn Zone number
Cc 0x36
Ac Answer code
Dl 0x01
Data1 0x00 — 0x0C – Bass is 0dB — +12dB
0x81 — 0x8C – Bass is -1dB — -12dB
Et 0x0D
COMMAND:
Byte: Description:
St 0x21
Zn Zone number
Cc 0x37
Dl 0x01
Data 0xF0 – Request current Room EQ state
0x01 – Room EQ 1 on
0x02 – Room EQ 2 on
0x03 - Room EQ 3 on
ox04 - Room EQ off
Et 0x0D
RESPONSE:
Byte: Description:
St 0x21
Zn Zone number
Cc 0x37
Ac Answer code
Dl 0x01
Data1 0x00 – Room EQ is off
0x01 – Room EQ 1 is on
0x02 - Room EQ 2 is on
0x03 - Room EQ 3 is on
0x04 – Room EQ has not been calculated and is therefore off
Et 0x0D