Owner's Manual
Table Of Contents
- Handbook
- Factory default reset
- Safety Guidelines
- Welcome
- Contents
- Before You Begin
- Trademark Acknowledgments
- Rear Panel Connections and Controls
- Audio/Video Connections
- Connection Guide
- Radio & Wireless Audio Connectors
- Other Connectors
- Speakers
- Connecting Speakers
- Operation
- Extended front panel menu
- Front Panel Operation
- Remote Control
- Device Mode/Source keys
- Customising the Remote
- Essential Setup
- Auto Speaker Setup
- Setup Menus
- Connecting to a Network
- Decoding Modes
- Tuner Operation
- Troubleshooting
- Specifications
- Device Code Tables
- Custom Installation Notes
- Contents
- Introduction
- Set-up
- Conventions
- Serial Cable Specification
- Example command and response sequence
- System Command Specifications
- Input Command Specifications
- Output Command Specifications
- Menu Command Specifications
- Setup Adjustment Command Specifications
- Treble Equalisation (0x35)
- Bass Equalisation (0x36)
- Room Equalisation (0x37)
- Dolby Volume (0x38)
- Dolby Leveller (0x39)
- Dolby Volume Calibration Offset (0x3A)
- Balance (0x3B)
- Subwoofer Trim (0x3F)
- Lipsync Delay (0x40)
- Compression (0x41)
- Request incoming video parameters (0x42)
- Request incoming audio format (0x43)
- Request incoming audio sample rate (0x44)
- Set/Request Sub Stereo Trim (0x45)
- Set/Request Zone 1 OSD on/off (0x4E)
- Set/Request Video Output Switching (0x4F)
- Set/request input name (0x20)
- FM Scan up/down (0x23)
- DAB Scan (0x24)
- Heartbeat (0x25)
- Reboot (0x26)
- Bluetooth status (0x50)
- Setup (0x27)
- Room EQ name(s) (0x34)
- Now Playing Information (0x64)
- Input config (0x28)
- General Setup (0x29)
- Speaker Types (0x2A)
- Speaker Distances (0x2B)
- Speaker Levels (0x2C)
- Video Inputs (0x2D)
- HDMI settings (0x2E)
- Zone settings (0x2F)
- Network (0x30)
- Bluetooth (0x32)
- Engineering menu (0x33)
- AV RC5 command codes
- Product Info
- Mandatory Software Update
- Software Release Notes
- Warranty & Product Registration
18
Dolby Volume (0x38)
Control the status of the Dolby volume system.
Example
Command/response sequence to turn the Dolby Volume system on:
Command: 0x21 0x01 0x38 0x01 0x01 0x0D
Response: 0x21 0x01 0x38 0x00 0x01 0x02 0x0D
Dolby Leveller (0x39)
Control the status of the leveller component of the Dolby volume system.
Example
Command/response sequence to set the Dolby Leveller to 5:
Command: 0x21 0x01 0x39 0x01 0x05 0x0D
Response: 0x21 0x01 0x39 0x00 0x01 0x05 0x0D
Dolby Volume Calibration Oset (0x3A)
Adjust the calibration oset of the Dolby volume system.
Example
Command/response sequence to set the calibration oset to -5dB:
Command: 0x21 0x01 0x3A 0x01 0x85 0x0D
Response: 0x21 0x01 0x3A 0x00 0x01 0x85 0x0D
COMMAND:
Byte: Description:
St 0x21
Zn Zone number
Cc 0x38
Dl 0x01
Data 0x00 – Dolby Volume off
0x01 – Dolby Volume on
0xF0 – Request current Dolby Volume mode
Et 0x0D
RESPONSE:
Byte: Description:
St 0x21
Zn Zone number
Cc 0x38
Ac Answer code
Dl 0x01
Data1 0x00 – Dolby Volume is off
0x01 – Dolby Volume is on
Et 0x0D
COMMAND:
Byte: Description:
St 0x21
Zn Zone number
Cc 0x39
Dl 0x01
Data 0x00 — 0x0A – Set Dolby Leveller to 0 — 10
0xF0 – Request current Dolby Leveller setting
0xF1 – Increment Dolby Leveller setting
0xF2 – Decrement Dolby Leveller setting
0xFF – Turn off Dolby Leveller
Et 0x0D
RESPONSE:
Byte: Description:
St 0x21
Zn Zone number
Cc 0x39
Ac Answer code
Dl 0x01
Data1 0x00 — 0x0A – Dolby Leveller setting is 0 — 10
0xFF – Dolby Leveller is off
Et 0x0D
COMMAND:
Byte: Description:
St 0x21
Zn Zone number
Cc 0x3A
Dl 0x01
Data 0x00 — 0x0F – Set the calibration offset to 0 — 15dB
0x81 — 0x8F – Set the calibration offset to -1 — -15dB
0xF0 – Request current calibration offset
0xF1 – Increment the calibration offset by 1dB
0xF2 – Decrement the calibration offset by 1dB
Et 0x0D
RESPONSE:
Byte: Description:
St 0x21
Zn Zone number
Cc 0x3A
Ac Answer code
Dl 0x01
Data1 0x00 — 0x0F – Calibration offset is 0 — 15dB
0x81 — 0x8F – Calibration offset is -1 — -15dB
Et 0x0D