Owner's Manual
Table Of Contents
- Handbook
- Factory default reset
- Safety Guidelines
- Welcome
- Contents
- Before You Begin
- Trademark Acknowledgments
- Rear Panel Connections and Controls
- Audio/Video Connections
- Connection Guide
- Radio & Wireless Audio Connectors
- Other Connectors
- Speakers
- Connecting Speakers
- Operation
- Extended front panel menu
- Front Panel Operation
- Remote Control
- Device Mode/Source keys
- Customising the Remote
- Essential Setup
- Auto Speaker Setup
- Setup Menus
- Connecting to a Network
- Decoding Modes
- Tuner Operation
- Troubleshooting
- Specifications
- Device Code Tables
- Custom Installation Notes
- Contents
- Introduction
- Set-up
- Conventions
- Serial Cable Specification
- Example command and response sequence
- System Command Specifications
- Input Command Specifications
- Output Command Specifications
- Menu Command Specifications
- Setup Adjustment Command Specifications
- Treble Equalisation (0x35)
- Bass Equalisation (0x36)
- Room Equalisation (0x37)
- Dolby Volume (0x38)
- Dolby Leveller (0x39)
- Dolby Volume Calibration Offset (0x3A)
- Balance (0x3B)
- Subwoofer Trim (0x3F)
- Lipsync Delay (0x40)
- Compression (0x41)
- Request incoming video parameters (0x42)
- Request incoming audio format (0x43)
- Request incoming audio sample rate (0x44)
- Set/Request Sub Stereo Trim (0x45)
- Set/Request Zone 1 OSD on/off (0x4E)
- Set/Request Video Output Switching (0x4F)
- Set/request input name (0x20)
- FM Scan up/down (0x23)
- DAB Scan (0x24)
- Heartbeat (0x25)
- Reboot (0x26)
- Bluetooth status (0x50)
- Setup (0x27)
- Room EQ name(s) (0x34)
- Now Playing Information (0x64)
- Input config (0x28)
- General Setup (0x29)
- Speaker Types (0x2A)
- Speaker Distances (0x2B)
- Speaker Levels (0x2C)
- Video Inputs (0x2D)
- HDMI settings (0x2E)
- Zone settings (0x2F)
- Network (0x30)
- Bluetooth (0x32)
- Engineering menu (0x33)
- AV RC5 command codes
- Product Info
- Mandatory Software Update
- Software Release Notes
- Warranty & Product Registration
23
Set/Request Zone 1 OSD on/o (0x4E)
Set/Request whether the Zone 1 OSD is shown.
Example
Command/response sequence to set the Zone 1 OSD to ‘O’:
Command: 0x21 0x01 0x4A 0x01 0xF2 0x0D
Response: 0x21 0x01 0x4A 0x00 0x00 0x01 0x0D
COMMAND:
Byte: Description:
St 0x21
Zn 0x01
Cc 0x4E
Dl 0x01
Data 0xF0 – Request current Zone 1 OSD on/off state.
0xF1 – Set Zone 1 OSD to On.
0xF2 – Set Zone 1 OSD to Off.
Et 0x0D
RESPONSE:
Byte: Description:
St 0x21
Zn 0x01
Cc 0x4E
Ac Answer code
Dl 0x01
Data1 0x00 – Zone 1 OSD is On.
0x01 – Zone 1 OSD is Off.
Et 0x0D
Set/Request Video Output Switching (0x4F)
Set/Request the HDMI video output selection.
Example
Command/response sequence to set the video output to HDMI output 1:
Command: 0x21 0x01 0x4F 0x01 0x02 0x0D
Response: 0x21 0x01 0x4F 0x00 0x01 0x02 0x0D
COMMAND:
Byte: Description:
St 0x21
Zn 0x01
Cc 0x4F
Dl 0x01
Data 0x02 – Set HDMI Output 1.
0x03 – Set HDMI Output 2.
0x04 – Set HDMI Output 1 & 2.
0xF0 – Request current video output switching setting.
Et 0x0D
RESPONSE:
Byte: Description:
St 0x21
Zn 0x01
Cc 0x4F
Ac Answer code
Dl 0x01
Data1 0x02 – HDMI Output 1.
0x03 – HDMI Output 2.
0x04 – HDMI Output 1 & 2.
Et 0x0D
Set/request input name (0x20)
is command returns the name of an input if renamed by the user. It can also
be used to set the input name.
Example
Command/response sequence for setting the current input to “BDP300”:
Command: 0x21 0x01 0x20 0x06 0x42 0x44 0x50 0x33 0x30 0x30
0x0D
Response: 0x20 0x01 0x20 0x00 0x06 0x42 0x44 0x50 0x33 0x30
0x30 0x0D
COMMAND:
Byte: Description:
St 0x21
Zn 0x01
Cc 0x20
Dl 0x01 (query) or <n> (limited to 10 characters) for setting name
Data F0 - query
1-<n>
Et 0x0D
RESPONSE:
Byte: Description:
St 0x21
Zn Zone Number
Cc 0x20
Ac Answer code
Dl Data length - <n> if setting, 0x0A if requesting the name
Data1 -
Data <n>
Input name in ASCII characters
Et 0x0D