Owner's Manual
Table Of Contents
- Handbook
- Factory default reset
- Safety Guidelines
- Welcome
- Contents
- Before You Begin
- Trademark Acknowledgments
- Rear Panel Connections and Controls
- Audio/Video Connections
- Connection Guide
- Radio & Wireless Audio Connectors
- Other Connectors
- Speakers
- Connecting Speakers
- Operation
- Extended front panel menu
- Front Panel Operation
- Remote Control
- Device Mode/Source keys
- Customising the Remote
- Essential Setup
- Auto Speaker Setup
- Setup Menus
- Connecting to a Network
- Decoding Modes
- Tuner Operation
- Troubleshooting
- Specifications
- Device Code Tables
- Custom Installation Notes
- Contents
- Introduction
- Set-up
- Conventions
- Serial Cable Specification
- Example command and response sequence
- System Command Specifications
- Input Command Specifications
- Output Command Specifications
- Menu Command Specifications
- Setup Adjustment Command Specifications
- Treble Equalisation (0x35)
- Bass Equalisation (0x36)
- Room Equalisation (0x37)
- Dolby Volume (0x38)
- Dolby Leveller (0x39)
- Dolby Volume Calibration Offset (0x3A)
- Balance (0x3B)
- Subwoofer Trim (0x3F)
- Lipsync Delay (0x40)
- Compression (0x41)
- Request incoming video parameters (0x42)
- Request incoming audio format (0x43)
- Request incoming audio sample rate (0x44)
- Set/Request Sub Stereo Trim (0x45)
- Set/Request Zone 1 OSD on/off (0x4E)
- Set/Request Video Output Switching (0x4F)
- Set/request input name (0x20)
- FM Scan up/down (0x23)
- DAB Scan (0x24)
- Heartbeat (0x25)
- Reboot (0x26)
- Bluetooth status (0x50)
- Setup (0x27)
- Room EQ name(s) (0x34)
- Now Playing Information (0x64)
- Input config (0x28)
- General Setup (0x29)
- Speaker Types (0x2A)
- Speaker Distances (0x2B)
- Speaker Levels (0x2C)
- Video Inputs (0x2D)
- HDMI settings (0x2E)
- Zone settings (0x2F)
- Network (0x30)
- Bluetooth (0x32)
- Engineering menu (0x33)
- AV RC5 command codes
- Product Info
- Mandatory Software Update
- Software Release Notes
- Warranty & Product Registration
28
Input cong (0x28)
Sends input cong menu info.
COMMAND:
Byte: Description:
St 0x21
Zn 0x01
Cc 0x28
Dl 0x01 / 0x1B
Data1
Data 1-21
0xF0 - request Input config
set input config as below
Et 0x0D
RESPONSE:
Byte: Description:
St 0x21
Zn Zone Number
Cc 0x28
Ac Answer code
Dl 0x1B
Data1-10
Data11
Data12
Data13
Data14
Data15
Data16
Data17
Data18
Data19
Data20
Data21
Data22
Data23
Data24
Data25
Data26
Data27
Input name
0xnn - Input name in ASCII characters
Lip Sync
0x00 - 0x32 Lip sync in 5mS steps
Mode
0x00 - Last mode
0x01 - Stereo
0x02 - Stereo Direct
0x03 - Dolby Surround
0x04 - DTS Neural:X
0x05 - Virtual Height
0x06 - 7 Ch Stereo Mode
0x07 - Auro-Matic
0x08 - Reserved
MCH mode
0x00 - Last mode
0x01 - Native
0x02 - Stereo Downmix
0x03 - Virtual Height
0x04 - Native Upmixer (Dolby Surround, DTS Virtual:X)
0x05 - Reserved
Bass
0x00 - 0x0C – Bass is 0dB — +12dB
0x81 - 0x8C – Bass is -1dB — -12dB
Treble
0x00 - 0x0C – Treble is 0dB — +12dB
0x81 - 0x8C – Treble is -1dB — -12dB
Room EQ
0x00 - Room EQ off
0x01 - Room EQ1, 0x02 - Room EQ2, 0x03 - Room EQ3
0x04 - Not calculated
Input Trim
0x00 - 1V
0x01 - 2V
0x02 - 4V
Dolby Volume
0x00 - Dolby Volume off
0x01 - Dolby Volume on
Dolby Leveller
0x00 — 0x0A – Dolby Leveller setting is 0 — 10
0xFF – Dolby Leveller is off
Dolby Calibration Offset
0x00 — 0x0F – Calibration offset is 0 — 15dB
0x81 — 0x8F – Calibration offset is -1 — -15dB
Stereo mode
0x00 - Left/Right
0x01 - Left/Right+Sub
0x02 - Sub+Sat
0x03 - As speaker types
Sub Stereo
0x00 - 0dB
0x81 — 0x94 – Sub Stereo is -0.5 — -10dB
IMAX Enhanced mode
0x00 - Auto
0x01 - On
0x02 - Off
Auro-Matic 3D
0x00 - Small, 0x01 - Medium, 0x02 - Large, 0x03 - Movie, 0x04 - Speech
Auro-Matic Strength
0x00 - 0x10 - 0-16
Audio Source
0x00 – Analogue audio is in use for the current source.
0x01 – Digital audio is in use for the current source.
0x02 – HDMI audio is in use for the current source.
CD Direct
0x00 - CD Direct off, 0x01 - CD Direct on
Et 0x0D