Owner's Manual
Table Of Contents
- Handbook
- Factory default reset
- Safety Guidelines
- Welcome
- Contents
- Before You Begin
- Trademark Acknowledgments
- Rear Panel Connections and Controls
- Audio/Video Connections
- Connection Guide
- Radio & Wireless Audio Connectors
- Other Connectors
- Speakers
- Connecting Speakers
- Operation
- Extended front panel menu
- Front Panel Operation
- Remote Control
- Device Mode/Source keys
- Customising the Remote
- Essential Setup
- Auto Speaker Setup
- Setup Menus
- Connecting to a Network
- Decoding Modes
- Tuner Operation
- Troubleshooting
- Specifications
- Device Code Tables
- Custom Installation Notes
- Contents
- Introduction
- Set-up
- Conventions
- Serial Cable Specification
- Example command and response sequence
- System Command Specifications
- Input Command Specifications
- Output Command Specifications
- Menu Command Specifications
- Setup Adjustment Command Specifications
- Treble Equalisation (0x35)
- Bass Equalisation (0x36)
- Room Equalisation (0x37)
- Dolby Volume (0x38)
- Dolby Leveller (0x39)
- Dolby Volume Calibration Offset (0x3A)
- Balance (0x3B)
- Subwoofer Trim (0x3F)
- Lipsync Delay (0x40)
- Compression (0x41)
- Request incoming video parameters (0x42)
- Request incoming audio format (0x43)
- Request incoming audio sample rate (0x44)
- Set/Request Sub Stereo Trim (0x45)
- Set/Request Zone 1 OSD on/off (0x4E)
- Set/Request Video Output Switching (0x4F)
- Set/request input name (0x20)
- FM Scan up/down (0x23)
- DAB Scan (0x24)
- Heartbeat (0x25)
- Reboot (0x26)
- Bluetooth status (0x50)
- Setup (0x27)
- Room EQ name(s) (0x34)
- Now Playing Information (0x64)
- Input config (0x28)
- General Setup (0x29)
- Speaker Types (0x2A)
- Speaker Distances (0x2B)
- Speaker Levels (0x2C)
- Video Inputs (0x2D)
- HDMI settings (0x2E)
- Zone settings (0x2F)
- Network (0x30)
- Bluetooth (0x32)
- Engineering menu (0x33)
- AV RC5 command codes
- Product Info
- Mandatory Software Update
- Software Release Notes
- Warranty & Product Registration
33
Speaker Levels (0x2C)
Set / request speaker level menu info.
COMMAND:
Byte: Description:
St 0x21
Zn 0x01
Cc 0x2C
Dl 0x01 / 0x12
Data1
Data 1-16
0xF0 - request Speaker Levels
set Speaker Levels as below
Et 0x0D
RESPONSE:
Byte: Description:
St 0x21
Zn Zone Number
Cc 0x2C
Ac Answer code
Dl 0x12
Data1
Data2-17
Data18
Test tone
0x00 - Internal
0x01 - External
Speaker level
0x00 — 0x14 –0dB — +10dB
0x81 — 0x94 –0.5dB — -10dB
Front Left, Centre
Front Right
Surr. Right
Surr. Back Right
Surr. Back Left
Surr. Left
Left Top Front
Right Top Front
Left Top Back
Right Top Back
Subwoofer
Channel13
Channel14
Channel15
Channel 16
Noise output
0x00 - None (switch off audio noise output)
0x01 - Front Left
0x02 - Centre
0x03 - Front Right
0x04 - Surr. Right
0x05 - Surr. Back Right
0x06 - Surr. Back Left
0x07 - Surr. Left
0x08 - Left Top Front
0x09 - Right Top Front
0x0A - Left Top Back
0x0B - Right Top Back
0x0C - Subwoofer
0x0D - Channel 13
0x0E - Channel 14
0x0F - Channel 15
0x10 - Channel 16
Et 0x0D